175 KW -175 KVA 264 amps at 460v John Deere diesel powered 460v - 208v - 115v outlets housed in a container with ample access doors

This unit needs a new seal that costs about $75.

2022 Kiln-Direct Piggy Back Kiln New, Never Used 1999 53' Trailer

14@ x 16” inlet 16” Round inlet no motor

LM Bump Rollcase Package Saw Includes waste conveyor under saw and elevated conveyor 550v/3 phase Approx 55" Bar Already dismantled and ready to load, as shown in the last two photos.

LAMB 23x27 inch opening grinder with 150 HP motor, 1 3/8” screen and starter control. 460 volt 3-phase

Model # 01-1172-05-01 60” x 142” table size (1) available no hydraulic units or hand control

Rip Saw Model SDL 1200 Edging Conveyor Model UHY 1900

This system was purchased used and never put into service.

MAC 114LST100 Dust Collector 12x10 Rotary Airlock Hopper and leveling screws Air flow: 18,000 ACFM Media: 2,000 sq ft 12 Gauge Carbon steel exterior Clean air plenum Guard rail Nema 4 enclosureHopper discharge to match airlock Magnehelic pressure differential gauge kit (100) 6" x 144" 16 oz Polyester bags 60 HP Motor, 460 V System has already been dismantled and is ready to load.

- Min. panel length 9.06 inch - Max. panel length 10 ft 5.98 inch - Min. panel width 8.27 inch - Max. panel width 4 ft 3.18 inch - Panel stack station - no. stations 1 loading - Max. panel stack height 5 ft 2.99 inch - Work capacity 13 Cycles/min - Lifting capacity 100 Kg - Panel stack infeed - Movement system with frame System suction cups - Vacuum pump - no. pumps 1 - Control system - PLC MAGELIS

The Rip Saw is still in good running condition and still in use.

Vance PT600R8 Drum Chipper See this machine at IWF Atlanta 2024! This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

This Grinder was recently taken out of service and was running good. No electrical controls. Ready to load.

This Grinder was recently just taken out of service. It ran very good before taken out. Does not include electrical controls.

Vecoplan RG 42/60 XL 60 HP Motor 15" Rotor 42" x 52" Hopper Opening 1" Screen This machine went through a rebuild. It was not big enough for the buyers application. Available immediately.

Vecoplan RG52-60 U Stretch Slow Speed Grinder 60 HP Motor No Control Panel

Vecoplan Model 45/12/2VU HZF Grinder 75 HP Motor 18" Wide opening No Vibrating Infeed conveyor

Vermeer HG365 Grinder New infeed roll and remote control Ready to go to work!

Viking Sentinel Nailing System Per seller: Machine was idled several years ago. Was functioning at that time. Missing one overload relay in main control cabinet which we can provide info. Other than that, should just need cleaning and a little TLC. Estimated footprint 13’ X 26’ not including area for raw material. Volume totally dependent on number of boards and condition, new or used, bowed are straight, etc. Right Hand Setup 208 V (3PH) 4th Stringer Tooling Wing Pallet to 4" Automatic Pallet Stacker