Mereen-Johnson Model 441-DC Gang Rip Saw Capacity: Arbor space 41” Arbor Drive: 75 HP 3600 RPM TEFC motor Feed Drive: HP TEFC variable speed direct; 45’ to 225’ feet per minute Hold Downs & Bed Plate: Four 5” dia. Air loaded high yield idle press rolls Saw Sleeve: One 41” capacity sleeve Dust Collection: Four upper dust pick-ups: two (2) 8” dia., two(2) 4” dia., one lower 4”dia. Pick-up:(requires total 4820 CFM @ 5,000 feet per minute) Swing Arm & Tip-Up Cart: One floor mounted dual shaft swing arm and one tip-up saw sleeve set-up cart Electrical: Arranged for 3 phase, 60 cycle, 460V Cameron Automated Opti-Rip Model #34F-M1 System: Manufacture Year: (2004) Complete with length measurement Tally System 5 infeed belt and chains for feeding a Gang Rip saw up to 41” wide 16 width sensors 3 sets of pinch rolls for short stock 1 fixed & 4 movable laser lights This system feed for 4’ to 16’ max lumber length It feeds from operator right to left Wired 220V; If 440V required, a transformer will be needed

The seller has confirmed that this Mereen Johnson 441 Rip saw is in great working/running cnodition and it is ready to load! - 2004 Cameron Auto Opti-Rip Infeed - Model: 34F-M1 - Serial: OR164 - 100% Servo (only Servo is this Cameron) - Full amp load 81 - 44" W bed - Up to 20 saws can be run on the arbor - No moving blades BUT there are moving lasers Although this one has been pulled from service, they have an identical one still running and available for inspection....

These two rip saws were removed from service in working condition some time ago. The seller purchased them and never installed them. They have been in storage the whole time.

Mereen Johnson 424 DC Gang Rip Outfeed Rollers

Mereen Johnson 424 DC/SR4 Gang Rip Saw with Automated Infeed with multiple lasers manufacturer’s specs to be confirmed 24” width capacity 3-1/2” thickness capacity 75 HP main motor 3 hp feed motor feed rete 30-245 fpm

Mereen Johnson Model 312 Rip Saw Includes: New pads for the chain Includes: Twistlock Collar Mounted Saw Blades Available approx May 1, 2024

Mereen Johnson 424DC 24" Wide Arbor 75 HP Motor (460v/3Ph) 3 HP Feed Speed Variable Feed Speed Air loaded pressure rollers

Mereen Johnson Model 312 DC SR1R Rip Saw 600 V/3 PH/60 Cy

225 KVA 480 volt to 208Y/120

Miner 4” Edger

Montgomery 100 HP Hammer Mill Includes: Outfeed conveyor and Infeed Hopper

Main fan motor 20 HP RAL opening 14” Electrical panel Auto shaker filter cleaning Inlet pipe size 14” Number of filters 63

New Venture Manufacturing Gang Rip Saw Hydraulic Tank (5) Moving Blades Laser Tower Touchscreen Controls This machine has been removed from service. The photos showing the system setup were taken before it was removed

Seller bought this saw with the intention of rebuilding it. He has most of the parts and started the work, but needs the space in the shop immediately. The first few photos are of the machine as it sits now (stripped). The next few show the machine BEFORE they started working on it. Newman KM16 Trim Saw Unscrambler Misc parts - shown in photos - everything going with the saw

Newman End Trimmer K 20 MAXIMUM CUT LENGTH: 20' (6.1 m) 20' (6.1m) MINIMUM CUT LENGTH: 6' (1829 mm) 4' (1219 mm) 6' (1829 mm) MAXIMUM CUT THICKNESS: 7? (178 mm) 7-1/2? (190 mm) ACCURACY: +/- 1/32? (0.8 mm) +/- 1/32? (0.8 mm) FEED SPEEDS: 20 to 60 FPM (6.1 to 18.3 m/min.) FEED CHAINS: #60 roller chain #60 H type mill chain FEED DRAGS: 6 at 22? (559 mm) intervals 6 at 22? (559 mm) intervals SAW BLADES: 22? (559 mm) carbide, 60 teeth 1-1/2? (38.1 mm) bore, 10 gauge (3.4mm) 2 FLOOR SPACE: 20'-8? (6.3 m) x 6' (1.8 m) 20'-8? (6.3 m) x 6' (1.8 m) WEIGHT: Approximately 3500 lbs. (1590 kg) Approximately 3500 lbs. (1590 kg) 1`fixed saw and 4 movable saws 7.5HP each new electrical starters 1.5HP variable speed drive

Newman K20 Trim Saw (2) Blades - Aprox 20" diameter Infeed & Outfeed decks

16 HP 12 filter bags up 4 collection bags lower Lots of pipe

Northtech Chop Saw

Northteck MRS-14-DXL 460v Manufacturer notes: This is a very popular machine and cost effective. New open ended design allows for you to cut wide material up to 27-1/8? wide. Plus spare arbors, lasers, and the optional quick locking, easy to adjust infeed will not break the bank. The Northtech heavy-duty 50 HP multi-rip (“gang-rip”) saw with 15? maximum blade diameter quickly and accurately cuts material up to 4-15/16? thick and 27-1/8” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Laser guides (one included) and an optional 103” fence make proper alignment of even the longest material simple and precise. Variable feed speeds of 25 – 120 FPM and powered height adjustment further improve operator efficiency.

Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door