Nyle L200M Dry Kiln System still under power. Purchased new in 2021.

2015 Nyle L500 Dry Kiln 5 hp Compressor 5 24" fans Chimney All Controls Included Very Good Condition

2003 Nyle L500 Dry Kiln 8 Fans and Insulated Container Included Good Condition Available Immediately

2004 Nyle L1200S Dry Kiln Good Condition Available Immediately

Nyle L1209 Dry Kiln 230 volt 3 Phase No enclosure …controls only

Nyle Dry Kilns - 2024 Kiln: 29' x 42', 40 MBF with HT54 - (2) 1998 Kilns: 28' x 40'. Both units in good running condition. New controls in 2016. - 1994 Kiln: Missing some sheet metal and attached to a storage building. 28'x40' There is one new kiln and three older kilns that the seller has available. All are ready to be removed from the current location. The older kilns had new controls installed in 2016.

Oliver Sawmill New Carriage Wheels New battery

7.5 HP single phase cyclone/dust collection assorted dust pipe and fittings as pictured

Optimatic TS-06 Tooth Straightener Manufacturer specs: Every Tooth - Every Run - Every Time Introducing the TS06 automatic bandsaw tooth straightener. This latest Filing Room innovation from OPTIMATIC is designed to work in place of the backfeed on a bandsaw sharpener. The TS06 is timed from the feed of the bandsaw sharpener. Each tooth is examined as it passes through the sensor. When a tooth is not aligned properly it will bend it back to correct it. Teeth are examined on each round of the grinder, giving the tooth straightener the opportunity to examine each tooth several times as the saw is processed and make progressive improvement putting the tooth back in line. A standard 5' resaw can generally be processed in 30 minutes. The TS06 is designed to measure the body of the tooth, just below the grinding burr and just behind the swage or tip. The actual contact point is easily adjustable. It's important to measure the body of the tooth so that we do not cover up problems with swages, shapers, or tippers. - but instead provide them a square, strong tooth to work from. 1. The TS06 has two stations. The first station feeds then measures. 2. The second station bends. Specifications:Connection values:Electrical connetion:220 V 50 Hz or special voltageAir Pressure:1/4? Gas threadAir:Minimum 5 bar air consumption, 1 liter per strokeSaw blade diameter:Saw Wide:From 80 mm to 300 mm wide or special up to 420 mmSaw Long:From 6 m in the grinding machine carousel can be integratedSaw Thickness:0,7 mm to 2,7 mmDimensions:Length:1350 mmHeight:1550 mmWidth:600 mmWorking position:1000 mm can be adapted to grinding heightWeight:210 kg

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

This machine was reported to be in running condition when removed from service. Looks like a Pendu. Cannot find a plate on the machine to confirm. this is a single arbor gang and it does not have a sizer. 75 HP Main Motor 5 HP Drive motor

Pendu E-4000 Gang Saw 75 HP on bottom and 75 HP on top arbors 20 HP on blower Press rolls are all original and in very good condition Comes with starters and 3000 amp disconnect box Some hydraulic upgrades Very good condition Seller will disconnect and load

Pendu M-4000 Gangsaw 75 HP on bottom and 75 HP on top arbors 20 HP on blower Press rolls are all original and in very good condition Came from sheltered workshop and was never used much Comes with starter boxes Will disconnect and load.

Pendu 1400 Drill Station Includes: Some misc drill bits and infeed pieces

Selling as a complete package: Pendu Sharp Chain Scragg (2) 100 HP Motors with soft starts Infeed System Log turner Operator Cab All controls and electrical (2) Log Decks: 3-Strand and 4-Strand Pendu bark conveyor: 30'4" Long with 180 degree tail section, 17" flights 2" high, flights spaced 18-3/4" apart Barn Sweep: Elevated conveyor: 25'4 Long, (2) Hold downs with idlers, chain has 17" flights that are 2" high, leg brackets, Approx 90' of Barn Sweep conveyor with chain and drive motor

The seller has confirmed that this Pneumafil 135 is available. Pneumafil Dust Collector Model 135 (13.5-460-8) 150 hp. The round duct enters the collector at 40" diameter & exits at 64" square

The seller of this Pneumafil dust collection system has confirmed that it is in great working/running condition and ready to be loaded! - 150HP - Round duct enters the colletor at 48" diameter

Precision 55 screener, was working when pulled out of production.

Precision 10'x20 Screen 3-Decks: 3/4” top deck, 1/4” middle deck screen

Precision Disc Scalping Screen Model PDS648 48” wide x approx 8’ long 6 shafts and the discs are stitch welded on