Chop Saw with Infeed Unscrambler Swing cut off with a 12" blade 5 HP Motor

2021 heavy duty 7.5 HP Used Dust Collector 220 V / 3 Ph / 60 Hz Dust Collector has an efficiency of 85%

8x24 Drum Dryer Webb stye burner Includes: Drum, burner, cyclone ductwork and blower

Table Top Measures 50x50 Hand Operated Air Valve To Raise & Lower Lower Height is 12 1/2 Total Raised Height is 27 1/2 All Air Operated 4,000 lb Capacity

????34' kiln with 5,500 BF of 4/4 lumber capacity Hot water system wood/oil boiler combo Wet bulb/dry bulb with 7 fans that change directions for air flow on adjustable timers 2 16'x5' karts Unit comes with 2 axles, tires, skirting for bottom enclosure, panel box with switches and timers

2000 lb Scissor Lift Table Good Condition

75 HP 550 Volt 3 phase

15 HP 460 volt 3-phase 63 CFM Capacity

USNR 60,000 Board Foot Kilns (10) Available

Vac-U-Clamp FT900 Thermafoil mPress Brand new - Seller never used it!

Vac-U-Clamp FT800+ Thermofoil Press 52" x 105" Work area Dispenser Rack (3) Vac bags new in boxes still

The Vantec 2800mm Spindleless Veneer Lathe is designed to process veneer for plywood production from both hard and soft logs. Its metal tempered grooved rollers and lathe knife inclination system work perfectly to make sure there will always be a precise contact area between the lathe knife and the log during the peeling process by eliminating vibration that could cause damage to the Veneer sheets. Vantec Spindleless lathe proves its efficiency by delivering consistent thickness variation and a impressive top linear speed of 180 m/ min throughout the peeling process for face or core veneers with smooth surfaces. - Log diameter up to 600 mm; - Max log length: 2750 mm; - Min log Length: 2300mm; (with stacker) - Min log length:1800mm (no stacker); - Veneer thickness: 1.0 to 4.0 mm; (Pine and eucalyptus); - Log core after peeling: 40 to 45mm; - Maximum linear speed 180 m/min; - Drive panel included; - Each motor is individually connected by a Variable Speed Drive for torque control in two points of traction on the rollers to pre- vent excessive load on tip ends; - Log Central aligner with maximum of 2200 mm of movement; - Pneumatic scriber Knives (02 fitted on the sides to cut in width and 01 in the Center to cut the length); - Width: 7640 mm; - Length: 3400 mm; - Height: 2550 mm; - Approximate weight: 14000 kg.

The Vantec Automatic Rotary clipper is designed to clip 2800 mm veneer sheets into specific sheet sizes as per the auto stacker preselection. It comes with electronic drive panel, automatic gauge system, positioning of clipper knife by Servomotor and encoder. It is de- signed to work with one tensioned clipper knife with gear motor. It also comes with a 2 HP motor on the output. The clipper knife is not included. - Veneer Thickness : 1 to 4 mm; - Max. Log: 2.750mm; - Minimum veneer width cut: 800 mm; - Max. Veneer length cut: 2700 mm; - Min. Veneer length cut: 700 mm; - Min. Venner rounding length: 150 mm; - Rotor gear motor: helical gears; - Clpper rollers power drive: 4 hp 6P; - Outlet conveyor Motor: 2hp 4P (input) 1 hp 8P (output); - Clipper Servomotor: 40 Nm (2x); - Width: 4800 mm; - Length: 6000 mm; - Height: 1700 mm; - Approximate weight: 7.000 kg

The Vantec Veneer Auto Stacker, ELV 1.82B is a Vacuum stacker for 2800 mm Veneer lathe. It is fitted with double stacking system (04 bins), with four veneer transport lines and four 5hp exhausters. with of two stoppers and eight ejecting arms. With drive Panel, VSD for exhaust fans and hydraulics lifting tables. Min veneer sheet length sheet: 2300 mm; • Max veneer sheet length sheet: 2700 mm (or Two sheets of 1350mm); • Min veneer sheet width: 800 mm; • Max veneer sheet width: 1500 mm; • Max height of stacks: 1000 mm; • Exhaust motor: 10 hp 4P (8x); • Inlet conveyor motor: 2hp 8P; • Transport conveyor motor: 6hp 4P; • Hydraulic pump motor: 5hp 4P (3x);

The Vantec Wood Wast Drum Chipper is used to produce chips from logs and veneer waste. It has a roller infeed system, rubber conveyor belt and hydro-pneumatic unit to lift the rotor for maintenance. Manufacturer specs: - Width of inlet: 600 mm; - Height: 200 mm; - Rotor diameter: 600 mm; - Toothed roller: 01 upper and 02 - lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical - gears); - Upper Rollers motor size: 5 hp; - Upper Rollers motor size: 5 hp; - Feed speed: 40m/min; - Number of rotor knives: 02; - Wood chip size: 30 - 40 mm; - Chipper screen: size: 65 x 65mm - Main motor 100 hp 4P: Included; Drive panel: Included; - Estimated production: 38 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 650 mm; - Height: 1 .000 mm; - Overall length: 5800 mm; Approximate weight: 2,900 kg.

This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

Vent Block Drill VBD New never used Motor: Heavy Duty 5 HP - 3 phase - 220v or 440 v (Please specify when ordering) Block Sizes: 2 x 4 through 2 x 12 on center 2 x 14 and larger off center Air Supply: 100 psi Drills: 3-wing Carbide Tipped Spindles: Alloy Steel - Double ended Frame: 2" Steel With Powder Coat Finish Covers: 10 Gauge (1/8" Thick) Aluminum Dimensions: Height - 60 inches, Width - 60 inches, Depth - 33 inches Shipping weight: 750 lbs. - (Including crate) New Never Used!!

Hawk CNC flooring end matcher Model HKH337 12/10/5/R/25 S/N HKH337A-20150420-01 Year 01/2016 380 Volt three phase, 160 amps Max working width 2540 mm (100") Min working width 400 mm (15.7") Max working thickness 25 mm (0.98") Min working thickness 3 mm (0.118") Min workpiece length 400 mm (15.7") Feed speed 5 to 100 m/min Table passline height 44" Top gravity infeed hopper feeder fences 2-1/4" wide rubber padded table feed chains Bolt on chain dogs mounted every 15-3/4" 36" infeed load space Table passline height 37-3/4" 1st station: (Left and right hand) Adjustable height tilting tip trim saws 4.0/6.2 Kw drive motors 2nd station: (Left and right hand) adjustable height tilting bottom trim saws 4.0/6.2 Kw drive motors 3rd station: (Left and right hand) adjustable height tilting shaper spindle 4.0/6.2 Kw drive motors 4th station: (Left and right hand) adjustable height tilting shaper spindle 4.0/6.2 Kw drive motors Servo controlled 4th station axis 5th station: (Left and right hand) adjustable height tilting shaper spindle 4.0/6.2 Kw drive motors 6th station: (Left and right hand) adjustable height tilting shaper spindle 4.0/6.2 Kw drive motors Mechanical digital readouts for station set up Pneumatic pressure shoes around shaping spindles Sound and safety enclosure around all stations Lift up access hoods with inspection windows 5.5 Kw feedworks drive motors Freestanding computer operator control station Weinview color touch screen display Push button master controls (1) Outfeed mounted conveyor deck with flooring board flipper (2) available and are priced as separate units.

HEESEMANN LSM-8 C/L Wide Belt Sander, (2) Heads 53" (1,300 mm) Width cap., (1) Segmented cross-belt & (1) longitudinal combination head with segmented platen. Head Configuration: · 1st Head: Segmented cross-belt, 5/8" wide segments (86 total) with "CSD" control, abrasive belt size 5.9" x 244", (5,400 mm X 150 mm ) inside chevron belt 5.9" x 191", sanding belt speed 5-12 m/s with 17 HP motor. (Inverter controlled) · 2nd Head: Combination head, with segmented polishing platen, 5/8" wide segments with CSD control, 17 HP motor, 106" x 53" ( 2,620 mm X 1,350 mm ) abrasive belt size. (Inverter controlled) Equipped with & Features: · HESSEMANN's patented "CSD" magnetic pressure adjustment system, sensors spaced every 5/8" (16 mm) sense part configuration; (2) mm part thickness variation can be sanded without sand through’s, pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if required. · The "CSD" computer control will hold approx. (20) programs or part configurations. · Additional features: Outfeed rotary panel cleaning brush with single end adjustment, 2 HP motor, air blast abrasive belt cleaners on all heads. · Variable feed speed from 13 to 82 FPM via Stober drive, 6.5 HP feed drive, motorized thickness opening 1/4" to 3-5/32" maximum. · Belt condition at 80% good.

Heeseman LSM8 Wide Belt Sander