Leadermac LMC 418-S 4 head moulder 20-80 FPM feed spiral head on bottom 460 volt 3 phase

Lico Rip System with 5-Moving Blades Includes: Infeed, tilt hoist, unscrambler, Lico infeed, 125 HP gang, outfeed tunnel, 75' sort chain Lateral Scanners High speed roller gang with (5) shifting blades: Up to 500 FPM Two Scanmeg scanners Singulating infeed Saw infeed fence Hogging blade to remove inside edging Outside edging falls off and into shredder New system upgrades in 2018

Lobo 6-Head Moulder 9" Wide capacity

Year: 2006 Working Width: 25mm to 230mm (1" to 9") Working Thickness: 8mm to 120mm (0.31" to 4.72") Bottom Spindles (x2): 40mm diameter, 0-20mm transverse movement, 6000 RPM, 5.5kW (7.5 HP) Top Spindles (x2): 40mm diameter, 0-20mm transverse movement, 6000 RPM, 7.5kW (10 HP) Side Spindles (x2): 40mm diameter, 0-20mm transverse movement, 6000 RPM, 5.5kW (7.5 HP) Configuration: Bottom, Side, Side, Top, Top, Bottom Feed Motor: 4kW (5.5 HP) Elevation Motor: 0.75kW (1 HP)

GB-CIS Single-end 575V / 3 Ph / 60 Hz 5” wide rubber pad conveyor Equipped with industrial motor for full power cutting and sanding capacity

Loewer Discmaster 6TD Brush Sander Vacuum Bed

Lower Denibbing Sander

This system was purchased used and never put into service.

MAC 114LST100 Dust Collector 12x10 Rotary Airlock Hopper and leveling screws Air flow: 18,000 ACFM Media: 2,000 sq ft 12 Gauge Carbon steel exterior Clean air plenum Guard rail Nema 4 enclosureHopper discharge to match airlock Magnehelic pressure differential gauge kit (100) 6" x 144" 16 oz Polyester bags 60 HP Motor, 460 V System has already been dismantled and is ready to load.

- Min. panel length 9.06 inch - Max. panel length 10 ft 5.98 inch - Min. panel width 8.27 inch - Max. panel width 4 ft 3.18 inch - Panel stack station - no. stations 1 loading - Max. panel stack height 5 ft 2.99 inch - Work capacity 13 Cycles/min - Lifting capacity 100 Kg - Panel stack infeed - Movement system with frame System suction cups - Vacuum pump - no. pumps 1 - Control system - PLC MAGELIS

Makor Start One M (S-ONE-M) Finishing Line Infeed & Outfeed System Storage Trolleys This line has been removed from operation and is in dry storage, as shown in the last (3) photos.

6-Roller Tray Oven (2) Available

System includes: Vacuum Coater UV Oven with (9) lamps Lateral Transfer Table Max width 9" Able to run clear or pigmented coating

Two Bay 52" capacity Pneumatic clamping

Marbel LS-1 Laminate Slitter

Marbel PR6-61 Closed End Pinch/Nip Roller 61" capacity 1500# of pressure with 5-1/2" diameter rollers 3" material thickness capacity feed rate 27 FPM 1/4 HP motor 115 volt

Marbel PR6-61 Closed End Pinch/Nip Roller 61" capacity 1500# of pressure with 5-1/2" diameter rollers 3" material thickness capacity feed rate 27 FPM 1/4 HP motor 115 volt

2005 Marathon Spray Booth 14' wide x 25.5' long x 8'9" tall Booth only no racks, spray guns, paint pots etc included

The Rip Saw is still in good running condition and still in use.

Mattison 404 Rip Saw Seller was using until they upgraded to a gang rip. Ready to ship.