Woodtech Cabinet Door Sander

Woodtech Modular Full Shop Dust Collection Sizes - 20,000- 77,000 CFM Negative airflow System - Keep the blowers clean, the sawdust or wood chips never damage the fans Multiple Blowers keep your system always running at optimal CFMs European Technology Grecon Spark Detection, All Pipe, Trunkline, and flex pipe included as a package NFPA rated Schneider Electronics

Woodtech will custom build your UV Finish Line! 24” 40” and 52” Width machines available 4 Head Wirebrush Single, Double, and triple Roll coaters 4 Head buffing Brush machine Denibbers Single, Double and Triple UV drying Ovens - with rotating Bulbs for safety 1M- 4M Conveyors 480V 3phase Schneider Electronics Touchscreen Operation Interlocking We can customize these machines to fit your needs

Panel Rip Saw available in 60" and 72" width capacity - Main Motor: 40 HP (460 V) - Infeed Motor: 3 HP - Main Spindle: 74 mm - Main Spindle Speed: 2500 RPM - Blade Diameter: 205 mm - Moveable blades with locking collars - Maximum Width: 60" or 70" - (12) Rubber Hold Down Rollers - Quick Change Blade Holders - Thickness Capacity: 0-30 mm - Variable Feed Speed: 0-15 meters/minute - Anti-Kickback Safeguard Options: - Semi Automatic Hydraulic Infeed & Outfeed Tables (3000 kg) - Automatic Infeed System (including lift table)

Woodtech HD Horizontal Band SawMax. workpiece size: 300mmThickness of production board: 5–160mmWidth of conveyor belt: 375mmDiameter of saw wheel: 711mmFeeding speed: 0-15m/minHydraulic pressure: 50-60kg/cmSize of saw blade: 185” Length, 2” wide, 1.6mm thick Electrical Requirements: Voltage: 460V/60 HZ/3 phaseFull electrical load: 18.5 KWOverall dimension: 2800L x 2200W x 2000H

Wysong Model 284 Horizontal Mortiser

Yaskawa Motoman UP50N Robot YR-UP50N-A00 Payload 50kg Control Box Teach Pendant Yaskawa Motoman UP50N Robot Type: YR-UP50N-A00 Payload 50kg

Yates A20-12 Planer Infeed Deck Tilt Hoist 575 V Includes: Misc parts, heads and attachments for S4S and T&G. This system was removed from service this Spring. It is ready to load.

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Planer Head Set Up Stand

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

There are two of these systems available. They were recently removed from the current operation and available immediately.

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

The seller has confirmed that this Yates American resaw was in working/running condition when it was pulled from production. It is ready to load! - Vertical resaw - All parts and blades included - Approximately 35 years old - 50-60HP - 440 amp

Yuasa saw analyzer, great working condition comes with saw centers, magnifying camera and monitor.

Air Compressor Water Separator Single Phase 115V 16hz Good Condition

Recently removed from service Available immediately

Brewco 4-Head Resaw Seller has a hydraulic unit to go with the machine. No controls. Optional: System can be cleaned up and controls added PER SELLER: this machine is able to pass 7.75" cants it was purchased in Nelson BC 20 years ago it has not run since it is ready to go but has only on off switches and no motor starters per se I have not pulled the machine out to clean and paint and get ready to move it needs cleaned/ painted/ starters for 4-20hp motors/ small hyd unit for feed belt and feed rolls nice machine, I have not operated it but was running when I bought it and has been under cover since will need 5 starters, and a small hyd unit 5 hp, which i can provide this machine is easy to get ready if we have a commitment

This system is no longer needed at the current facility. Ready for immediate removal! - Brewco Wolf Resaw - 4" Blade; 20'4" Long - 40" Bandwheels - 40 HP Main Motor - 10 HP Hydraulic Feed - McDonough Style Guides - Some spare blades - Head moves up/down, not the bed - Approximate dimensions: 9'L x 10'W x 6'H - Also available separately: - 8' Infeed Belt - 16' Outfeed Rollcase

Brewco B1600 Grade Resaw System 5-Way Board Separator Ready to load!