BRANDT - KDF 660, ...Edgebander w/Premilling & Corner RoundingSpecifications -- 0.4 - 15 mm (5/8") Edge cap.; panel thickness 5/16" - 2-3/8"; min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; -- Line Control (NO limit switches) for workstation function. -- Pressure beam height adjustment for all workstations via digital height indicator. -- PC-20 Program Control with: 12" Industrial PC screen; 256 MB RAM; 1 gB Flash card with USB Port & remote diagnostic link. -- Signal infeed light to insure proper spacing between panels.Equipped with: -- 2-Motor Premill unit; (2) 3 HP motors (12,000 RPM) with straight and chamfer capability; program controlled indexing from straight to bevel. -- Quick heat up glue system (approx. 10 minutes); hopper feeder & glue tank for maintenance & quick glue color change.Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for (15) minutes or more. -- The glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table; 800 mm dia. to accommodate large coils of 3 mm PVC stock); 3 mm PVC guillotine; (1) drive plus (3) secondary rollers "pneumatically controlled" pressure sections. Workstations: -- Double-end trim with: (2) 0.5 HP - 12,000 RPM motors; chamfers 0°- 15° via programmable Controller. -- Top & Bbottom flush/radius trim; bevels 0° - 15° (0.75 HP - 12,000 RPM motor); insert knives for 3 mm PVC radius. -- Corner Rounding Unit. -- Top & Bottom scraping for 3 mm PVC radius; pneumatically controlled indexing system. -- Top & Bottom oscillating buffing (0.25 HP - 2,800 motors). -- Variable feed speed 36 - 65 FPM (3 HP feed motor).

BRANDT - KDN 630, ...Edgebander.0.4 - 8 mm (5/16") Edge cap., panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8"), and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function.Equipped with: -- Quick heat up glue system, w/glue tank for maintenance, and glue color change. -- Automatic magazine for strip & coil (large coil table, 800 mm dia. to accommodate large coils of 3 mm PVC stock), 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections. Signal infeed light to insure proper spacing between panels. -- Automatic height adjustment with top pressure beam for all workstations, equipped with digital height indicator.Workstations: -- Double end trim (0.33 HP - 12,000 RPM motors), chamfers 0° - 15°. -- (2) Top & bottom flush/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor) with insert knives for 3 mm PVC radius. -- Top & Bottom scraping for 2 - 6 mm radius, pneumatically controlled blow off nozzles; Top & Bottom buffing (0.25 HP - 1,400 RPM motors). -- End trim & flush trim stations with: HF Motors, electronic brakes; feed chain track speed of 46 FPM, 2 HP feed drive. Complete with: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, PC-16 Program Control; with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, internal Modem for remote diagnostic link, and used tooling.

BRANDT KDN 210B Edgebander:0.4 - 3 mm (1/8") Edge thickness cap., 8 - 50 mm (0.3" - 2") panel thickness, 60 mm (2.3") min. panel width and 140 mm (5-1/2") min. length.Equipped with: -- Hot Melt granulate glue system with "Quick Melt" start-up (10 - 12 Min heat-up) with reversible rotation glue applicator roller and automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to re-activate). -- Automatic feed magazine, coil stock feeds automatically with guillotine cutoff, all strip stock are fed automatically through strip feed magazine. -- 3-Roller pressure section (1st driven, next (2) idle) w/electronically controlled and feed speed synchronized drive roll.Workstations: -- Vertical travel double-motor front & rear end trim with tilting of 0°- 15° cap. (0.24 HP - 12,000 RPM motors). -- Top & bottom flush/bevel trimmers (0.36 HP - 12,000 RPM motors), bevel 0° to 15°. -- Top & bottom buffing unit (0.15 HP - 2,750 RPM motors). -- Feed speed of 30 FPM. Features: -- Operator control panel at eye-level. -- Automatic height adjustment with top pressure beam for all work stations. -- Digital height indicator on holddown beam. -- Electronic motor brakes on trimmers.Complete with: 200 Hz Electronic frequency inverter, used tooling, sound enclosure w/window, and operators manual.

BRANDT AMBITION 1440 (KDF-440 C) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Adjustable Infeed Fence: Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Glue Scraping Unit: Flush on panel surface with floating insert knives. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 (KDF 440 C).

BRANDT AMBITION 1120 FC (aka KDF 120 C) (EDGEBANDER WPRE-MILL & CORNER ROUNDING): -- Specifications: Edge & Workpiece Capacity, 0.4 - 3 mm Edge cap., min. panel thickness 8 mm (0.3"), max. panel thickness 40 mm (1.57"), min. panel width 70 mm (2.75"). Min panel length: 140 mm (5.5")Line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all workstations. Auto in-feed stop to insure proper spacing between panels. Equipped with: -- Pre-Milling Station:(2) motors @ 0.75 kW (1.0 HP) ea., 12.000 RPM, LH & RH rotation w/pneumatic jump control for chip-free and clean panel edges. Equipped with diamond cutter heads. -- Gluing Section:Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, Pressure Section with (1) large drive plus (2) idle rollers "pneumatically controlled." Hot Melt granulate quick heat-up glue system. Workstations: -- End Trimming: 2 x 0.18 kW (1/4 HP), 12,000 RPM motors, THK guided, chamfers 0° - 15°. -- Flush/Bevel/Radius Trimming:2 x 0.55 kW (0.75 HP),12,000 RPM motors with insert knives for 3 mm PVC radius. cutter-heads, bevels 0° - 15°. -- Corner Rounding Station:1-Motor (4-corners) contour trim for profile corner rounding, 1 x 0.35 kW (0.5 HP), 12,000 RPM motor, with insert knivesFor 3 mm PVC radius w/digital read-out set-up and pneumatic change-over from thin to thick PVC edge tape. -- "Quick-Change" Profile Scraping Unit:Top & bottom for 2 - 3 mm radius, pneumatically controlled blow-off nozzles. -- Flat Scraping Unit:Top & bottom flat scraping units with copy wheels to remove residual glue squeeze-out. -- Operator & Machine Control: "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad.Production readiness displayed by traffic light indicator with ability to adjust units quickly thanks to direct access via ctrl keys. Intuitive, user-oriented navigation with a clear overview of the help and assistant functions, including the glue pot temperature or troubleshooting in plain text. -- Complete With: &#9679 Trim stations have HF motors w/electronic brakes &#9679 Fixed feed chain track speed of 8 MPM (26 FPM) &#9679 2 HP feed drive &#9679 208/230/440/480v, 3ph Transformer &#9679Sound/Safety Enclosure &#9679 Adjustable Out-Rigger Support &#9679 Used tooling. -- Actual Model is BRANDT AMBITION 1120 FC (aka KDF 120 C)

BRANDT AMBITION 1650 FC HIGH FLEX EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): Specifications: -- Edge thickness 0.4 - 12 mm (0.02" - 0.5"), incl. 3 mm (0.12") PVC banding. -- Workpiece thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width 70 mm (2.76"), Min. workpiece length 160 mm (6.37"). -- Working height 950 mm (37.8"). -- Variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units.Equipped with: -- 3 HP (2.2 kW) Feed motor for variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units. -- Infeed panel support with roller guide extends out to 800 mm (31.4"). Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") W Heavy Duty feed chain, with rubber pads, automatic chain track lubrication. -- Top pressure section with double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High-Frequency Motors); line control (no limit switches) for workstation functions. -- Top & bottom spraying device located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") Height.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads, Electro-pneumatic jump control on 1st motor, electronic frequency inverter for control of motor speed & braking, SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 KW, 3 KG (6.61 Lbs.) cap.; glue viscosities 25,000 - 80,000 mPa, temperature range 120° - 245° C (248° - 473° F); max. melting capacity 6 KG/Hr.EVA Hot Melt Glue Application System: -- QA 45 Quick-change glue tank with electronic switchable/emptying mode for easy maintenance & glue color change.Melting capacity approx. 6 - 10 KG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improved edge quality.Adjustable glue amount with servomotorPressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electropneumatic reset for straight or chamfer trimming. -- Top & Bottom Multi-stage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (4) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") ma

BRANDT AMBITION 1650 FC High Flex EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications: Edge thickness 0.4 - 12 mm (0.02" - 0.5"), incl. 3 mm (0.12") PVC banding. -- Workpiece thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width 70 mm (2.76"), Min. workpiece length 160 mm (6.37"). -- Working height 950 mm (37.8"). -- Equipped with:3 HP (2.2 kW) Feed motor for variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units. -- Infeed panel support with roller guide extends out to 800 mm (31.4"). Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") W Heavy Duty feed chain, with rubber pads, automatic chain track lubrication. -- Top pressure section with double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High Frequency Motors); line control (no limit switches) for workstation functions. -- Top & bottom spraying device located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") Height.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads, Electro-pneumatic jump control on 1st motor, electronic frequency inverter for control of motor speed & braking, SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 kW, 3 kG (6.61 Lbs) cap.; glue viscosities 25,000 - 80,000 mPa, temperature range 120° - 245° C (248° - 473° F); max. melting capacity 6 KG/Hr.EVA Hot Melt Glue Application System: -- Quick-change glue tank for easy maintenance & glue color change, melting capacity approx. 6 - 10 KG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improve edge quality.Pressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electro-pneumatic reset for straight or chamfer trimming. -- Top & Bottom Multistage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with a slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (2) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") max. edge thickness, 12 - 60 mm (0.50 - 2.375") workpiece thickness, quick-change motor system for different radius profiles, pneumatic (2) position indexing for different edge thicknesses

SAFETY SPEED 72GP EDGEBANDER -- Digital P.I.D. Temperature control Glue Pot that reduces overheating and burning of the glue. -- Standby temperature mode for small runs. -- Short 10 - 15 Min heat up time -- Digital Electronic temperature control. -- Adjustable Heat nozzle that saves energy. -- Electromagnetic guillotine end-trim means no compressed air needed. -- Accutrim edge trim system uses industrial duty trim routers to ensure a quality finish. -- Dust collection outlet to keep the part machine and floors clean. -- Automatic conveyor for consistent feed rate -- American Made.

SCM K400 E EDGEBANDER Edge Capacity,0.4 to 6 mm (0.016to 1/4")for strip feeding. -- Panel Capacity, min. width65 mm and 140 mm min. length, (2-3/8" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-1/2").Equipped with: -- Automatic strip & coil feed magazine, Teflon coated glue pot (heat-up time 10 Min), -- 3 mm cap. guillotine, 3-roll pressure unit. -- Startouch control system with large 12" screen, graphic display with one touch, memory capacity up to 60 working programs. --Workstations: -- Double motor front & rear end trim "K-2" mounted on THK guides (0.4 HP - 12,000 RPM) , tilts 0° - 15°, rapid set up between straight and angled cutting with the automatic tilting device. -- Top & bottom flush & bevel trims "RI/800" (0.7 HP - 12.000 RPM), bevels 0° - 15° with precision digital indicators for quick setup. -- Top & bottom "RAS/V" scraping unit with container with filter for long chips; -- Top & bottom buffing unit (0.25 HP - 2,800 RPM ). -- 36 FPM Fixed feed speed, 0.75 HP feed drive.Complete with: -- Full cover sound enclosure, mechanical digital readouts for setup adjustments, frequency inverter and outboard panel support. -- Actual Model: "OLIMPIC K 400 E".

SCMI MINI-MAX ME 25 EDGEBANDER, SINGLE SIDED SINGLE PHASE0.4 mm to 3 mm (1/8") Max. edge thickness cap. and 1.96" max. panel thickness; semi-automatic strip & coil feed magazine (feeds coil material automatically and strips one at the time); Teflon coated glue pot w/fast (8-10) Minute heat-up time, 1.2 mm cap. guillotine.Workstations: -- "ME 25" 2-Head -- Single motor end trim (0.8 HP - 12,000 RPM motor) -- Top & bottom flush trims (0.8 HP - 12,000 RPM ea. motor), straight or bevel cutters. -- Top & bottom scraping station. -- Top & bottom buffing, 3,000 RPM motors.22 FPM Fixed feed speed with 0.8 HP drive.Complete with: Sound enclosure, out rigger panel support, frequency converter, and used tooling on the stations.Features: Control Panel on machine infeed side Machine frame made of high rigidity ribbed steel to guarantee excellent support Top thick steel pressure beam with rubber coated wheels Manual adjustment of top beam with Auto positioning of operating units Numeric indicator of selected panel thickness Glue smoke-specific exhaust outlet; centralized extraction of the dust Panel support roller which can be extended the entire length of the machine

SCMI OLIMPIC K 600 T-ERL EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.4 to 3 mm For roll feeding and up to 8 mm for strip feeding. -- Panel Capacity: Min. panel width: 60 mm (2.375"); Min. panel length: 140 mm (5-1/2").Min./max. panel thickness: 8 - 54 mm (0.375" - 2.125"); min. distance between panels: 508 mm (20").Feed speed: 36 & 52 FPM (2.5 HP feed motor).Equipped with: -- Adjustable Infeed Fence:Manually preset with: Digital indicator, pneumatic in/out positioning; 1-coil feeder for banding up to 3mm thick with a 3 mm guillotine. -- Gluing Station:For EVA (Hot Melt) with quick change/disconnect Teflon glue pot for fast glue tanks change if needed. Heat-up time approx. (8 - 10) Min. -- Pressure Section:Manual digital positioning: Teflon-coated pneumatic driven roller & (2) spring-loaded idle rollers. - Includes "Strip Feed Magazine".Workstations: -- End Trimming Station: "K-SEL 2": Front & rear 0.5 HP - 12,000 RPM motor mounted on THK guides;, swivels 0° - 15°, rapid setup between straight and angled cutting with the automatic swivel cylinder. -- Top & Bottom Trimming Unit: 2 x 1.0 HP - 12,000 RPM Motors capable of tilting 0° to 25° degrees with copy wheels; pneumatic positioning for (3) settings: Flush/bevel/radius trimming via precision digital indicators; goes from 3 mm PVC to thin tape through the Controller for quick setup. -- 2-Motor Corner Rounding:(2) 0.80 HP Independent motors that slide on THK guides; features of the "Round-K" (SCM patent) allow for the double function of both the simultaneous trimming and rounding operations. -- Top & Bottom Profile Scraping Unit: "RAS/K" Profile scrape station for: 3 mm PVC, pneumatic positioning with digital indicators; large dia. copy wheels for max. accuracy, and pneumatic in/out positioning. -- Buffing Unit: Top/bottom; 2 x 1/4 HP - 2,800 RPM motors, tilting up to 12°.Operator & Machine Control: -- "STARTOUCH" Controller with: 12" Touchscreen displays; capable of storing (100) programs.Machine automation by PLC function and encoder positioned in the panel feed track pinion.Diagnostics for a quick solution to errors; process statistics data, i.e., No. of pieces/edges and track feeding.Features & Complete with: -- (1) 2.0 HP Feed drive motor. -- 200 Hz Frequency inverter for all trimming unit.; -- Manual adjustable hold-down pressure beam -- Full sound enclosure cover and outboard panel support. -- Adjustable side support. -- Replaceable track pads. -- Digital inverter for electronic motor braking. -- Acoustical safety enclosure. -- Dust Collection: Working units are individually ported on the top of the safety enclosure for max. efficiency. -- Actual model is: SCM OLIMPIC K 600 T-ERL

SCM OLIMPIC K360 COMPACT EDGEBANDER (W/PRE-MILLING) + EVA/PUR glue processing: -- Specifications: Edge Capacity, 0.4 to 6 mm (0.016 to 0.24") for strip feeding. Panel Capacity, min. width 65 mm & 140 mm min. length, (2.375" & 5.5"). Panel thickness min./max. 8 - 60 mm (0.315" - 2.36"). Equipped With: -- Adjustable In-feed Fence: Manually pre-set with digital indicator, pneumatic in/out positioning. -- Pre-Milling Station, RT-VP: Spindles 2 x 2.0 HP, 19,000 RPM, (1) with PLC controlled jump action and diamond cutter heads. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: SEGP Glue Pot for EVA /PUR processing, with Teflon coated glue tank and quick disconnect to change glue tanks fast if needed. Heat-up time approx. 10 Min. -- Pressure Section: Manual digital positioning, (3) pressure rollers, first roller is powered. Workstations: -- End Trimming Station: Front & rear 2 x 0.25 HP, 12,000 RPM motors mounted on THK guides, swivels 0ø - 15ø, rapid set up between straight and angled cutting with the automatic swivel cylinder. -- Top & Bottom Trimming Unit: Remote (via control panel) pneumatic positioning for (3) settings, flush/bevel/radius trimming, 2 x 0.7 HP - 12.000 RPM motors with precision digital indicators for quick setup. -- Top & Bottom Profile Scraping Unit "RAS/V": Manual pre-set up with digital indicators. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue Scraping Unit, "RC-V": Top/bottom flat glue scraper with pneumatic positioning through controller and air-blow off nozzle to keep the knifes clean. -- Buffing Unit: Top/bottom, 2 x 0.25 HP - 2,800 RPM motors, tilting up to 12°.Operator Interface: -- "STARTOUCH" Controller with: 12" Touchscreen display; capable of storing (100) programs. Machine automation by PLC function and encoder positioning. Diagnostics for a quick solution to errors.Process statistics data (i.e., number of pieces/edges) and track feeding.Complete With: -- Feed-speed, 36 FPM fixed, 1 x 2.0 HP feed drive motor, 200 Hz frequency inverter for all trimming units, manual adjustable hold-down pressure beam, full sound enclosure cover and outboard panel support. -- Actual Model: OLIMPIC K 360 TE.

SCMI K 208E SINGLE SIDED EDGEBANDER5/16" (8 mm) Max. edge cap., 1-3/4" max. banding height, 2-3/8" min. panel width and 6-/14" min. length. Equipped with: Automatic strip & coil feed magazine, Teflon coated glue pot (heat up time 10 Min), upgraded to Heavy Duty 3 mm PVC cap. guillotine, 3-roll pressure unit w/pneumatic controls. 42 FPM Fixed feed speed via 1 HP drive.Workstations: -- Double motor front & rear end trim (0.3 HP - 12,000 RPM motor ea.), tilts 0° - 15°, End trimmer mounted on 45° THK guides. -- Top & bottom trim station (0.8 HP - 12.000 RPM motor ea.), bevels 0° - 15°. -- Top & bottom PVC scraper for up to 5 mm radius; -- Top & bottom buffing unit (0.33 HP - 2,800 RPM motors). Complete with: Swivel control panel, pneumatic positioning of super finish, full cover sound enclosure, 200 Cy - 5 kW frequency converter & tooling.

SCMI OLIMPIC K 560TE EDGEBANDER (W/PRE-MILLING): -- Specifications: Edge Capacity: 0.4 to 6 mm (0.016 to 1/4") for strip feeding. -- Panel Capacity: Min. panel width: 60 mm (2.375"); min. panel length: 140 mm (5-1/2").Min./max. Panel thickness: 8 - 54 mm (0.375" - 2.125"); min. distance between panels: 600 mm (24").Equipped with: -- Pre-milling Station: (2) 2.0 HP (1.5 kW) motors; rectifies/cleans panels already sized. -- Adjustable Infeed Fence: Manually preset with digital indicator; pneumatic in/out positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with: Quick change/disconnect Teflon glue pot for fast glue tanks change if needed; Heat up time approx. (10) Min. -- Pressure Section: Manual digital positioning; Teflon coated pneumatic driven roller & (2) spring loaded idle rollers.Workstations: -- End Trimming Station: (2) Front & rear 1/2 HP - 12,000 RPM motors mounted on THK guides; swivels 0° - 15° for straight & angle cutting. -- Top & Bottom Trimming Unit: (2) 0.7 HP - 12.000 RPM Motors; capable of tilting & pneumatic positioning for (3) settings, flush/bevel/radius trimming for quick setup. -- Top & Bottom Profile Scraping Unit with: Digital indicators; large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue scraping Unit: Eliminates any excess glue. -- Buffing Unit: (2)Top/bottom 1/4 HP - 2,800 RPM motors; tilting up to 12°.Operator & Machine Control: -- "STARTOUCH" Controller with: 12" Touchscreen display; capable of storing (100) programs. -- Machine automation by PLC function and encoder positioned in the panel feed track pinion. -- Diagnostics for a quick solution to errors: Process statistics data (i.e., number of pieces/edges) and track feeding.Features & Complete with: -- 2-Speed feed speed of 40 & 60 FPM (12 & 18 MPM); (1) 2-1/2 HP feed drive motor. -- 200 Hz frequency inverter for all trimming units. -- Manual adjustable top hold-down pressure beam. -- Full sound enclosure cover and outboard panel support. -- Actual Model is: SCM OLIMPIC K 560TE

SCMI OLIMPIC K 600 T-ERL EDGEBANDER (W/PRE-MILL/CORNER ROUNDING): -- Specifications:0.4 to 3 mm For roll feeding and up to 8 mm for strip feeding.Panel Capacity: Min. Panel width 60 mm (2.375"); Min Panel length 140 mm (5.5").Min./max. Panel thickness 8 - 54 mm (0.375" - 2.125"); Minimum distance between panels 508 mm (20").Feed speed 36 and 52 FPM (2.5 HP feed motor) -- Equipped With:Adjustable In-feed Fence:Manually pre-set with digital indicator, pneumatic in/out positioning. 1-Coil feeder: For banding up to 3mm thick with a 3 mm guillotine.Gluing Station:For EVA (Hot Melt) with Quick change/disconnect Teflon glue pot for fast glue tanks change if needed. Heat-up time approx. 8-10 Min.Pressure Section:Manual digital positioning: Teflon-coated pneumatic driven roller & (2) spring-loaded idle rollers. Includes "Strip Feed Magazine" -- Workstations:End Trimming Station: "K-SEL 2" Front & rear 0.5 HP, 12,000 RPM motor mounted on THK guides, swivels 0° - 15°, rapid set up between straight and angled cutting with the automatic swivel cylinder. Top & Bottom Trimming Unit: 2 x 1.0 HP - 12.000 RPM Motors capable of tilting 0 to 25 degrees with copy wheels. Pneumatic positioning for (3) settings, flush/bevel/radius trimming via precision digital indicators to go from 3 mm PVC to thin tape through the controller for quick setup.Two Motor Corner Rounding:(2) 0.80 HP independent motors that slide on THK guides. The features of the "Round-K" (SCM patent) allow for the double function of both the simultaneous trimming and rounding operations Top & Bottom Profile Scraping Unit: "RAS/K" profile scrape station for 3 mm PVC with pneumatic positioning, with digital indicators. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. Buffing Unit: Top/bottom, 2 x 0.25 HP - 2,800 RPM motors, tilting up to 12°.Operator & Machine Control: "STARTOUCH" Controller with 12" touchscreen display, capable of storing 100 programs.Machine automation by PLC function and encoder positioned in the panel feed track pinion.Diagnostics for a quick solution to errors. Process statistics data, ie. No. of pieces/edges, and track feeding. -- Features & Complete With:1 x 2.0 HP feed drive motor; 200 Hz frequency inverter for all trimming units;Manual adjustable hold-down pressure beam;Full sound enclosure cover and outboard panel support.Adjustable side support. Replaceable track pads. Digital inverter for electronic motor braking Acoustical safety enclosure.Dust Collection: Working units are individually ported on the top of the safety enclosure for maximum efficiency.Suitable Transformer for 230V to 600V, 3 Ph. Actual model is SCM OLIMPIC K 600 T-ERL.

SCMI OLIMPIC K 800 T-FR2 EDGEBANDER EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Specifications: -- Edge Capacity, 0.4 to 8 mm (0.016 to 5/16") for strip feeding. -- Panel Capacity, min. width 65 mm and 140 mm min. length, (2-3/8" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-3/8"). Equipped With: -- Adjustable In-feed Fence: Manually pre-set with digital indicator and pneumatic panel spacing device. -- Pre-Milling Station, RT-E: Spindles 2 x 3.0 HP, 12,000 RPM, (1) with PLC controlled jump action and manual digital indicators positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with Teflon coated glue tank and quick disconnect to change glue tanks fast if needed. Heat-up time approx. 10 Min. -- Pressure Section: Servo motor positioning, (4) pressure rollers, first larger, Teflon coated and powered. Workstations: -- End Trimming Station K-SEL: Front & rear 2 x 0.5 HP, 12,000 RPM motors mounted on THK guides, swivels 0ø - 15ø, rapid set up between straight and angled cutting with the automatic swivel cylinder. -- Flush Trimming Unit: Top/Bottom, 2 x 1.0 HP, 12,000 RPM with 2 pre-set pneumatic positions, flush and overhang, remote pneumatic in/out positioning. -- Bevel/Radius Trimming Unit: Programmable, servo motor positioning, 2 x 1.0 HP - 12.000 RPM motors for change-over on the fly. -- Corner Rounding / Trimming Unit: For additional top & bottom trimming of linear an/or vertical leading & trailing corner when edgebanding all (4) sides, 2 x 0.8 HP - 12,000 RPM motor. -- Profile Scraping Unit "RAS/1000": Top/Bottom with (2) indexed manual pre-sets. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue Scraping Unit, "RC-V": Top/bottom flat glue scraper with pneumatic positioning through controller and air-blow off nozzle to keep the knifes clean. -- Buffing Unit "SPN": Top/bottom, oscillating 2 x 0.25 HP - 3,000 RPM motors, tilting up to 12°. -- Hot Air Unit: Single blower with adjustable heat range and directional heat shield for top/bottom coverage. Restores color luster on thick pvc edging materials that my be lost during the edge scraping process.Controls: -- Startouch Controller, 12" color touch screen, swivels 270° at in-feed of machine. Capable to store (100) programs, (6) at the touch of a single key. Graphical display of all working units. Tracks production data, diagnostic information and monitors maintenance schedules. Complete With & Features: -- Feed-speed, 36/52 FPM, 1 x 2.5 HP feed drive motor, 200 Hz frequency inverter for all trimming units. -- Electronic, programmable hold-down pressure beam positioning, lighted safety/sound enclosure cover and outboard panel support. -- Options Include: Dust Manifold as pictured. -- Actual Model: OLIMPIC K 800 T-FR2

SCMI OLIMPIC K 600 T-ERL EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:0.4 to 3 mm For roll feeding and up to 8 mm for strip feeding. -- Panel Capacity: Min. panel width: 60 mm (2.375"); Min. panel length: 140 mm (5-1/2").Min./max. panel thickness: 8 - 54 mm (0.375" - 2.125"); min. distance between panels: 508 mm (20").Feed speed: 36 & 52 FPM (2.5 HP feed motor).Equipped with: -- Adjustable Infeed Fence:Manually preset with: Digital indicator, pneumatic in/out positioning; 1-coil feeder for banding up to 3mm thick with a 3 mm guillotine. -- Gluing Station:For EVA (Hot Melt) with quick change/disconnect Teflon glue pot for fast glue tanks change if needed. Heat-up time approx. (8 - 10) Min. -- Pressure Section:Manual digital positioning: Teflon-coated pneumatic driven roller & (2) spring-loaded idle rollers. - Includes "Strip Feed Magazine".Workstations: -- End Trimming Station: "K-SEL 2": Front & rear 0.5 HP - 12,000 RPM motor mounted on THK guides;, swivels 0° - 15°, rapid setup between straight and angled cutting with the automatic swivel cylinder. -- Top & Bottom Trimming Unit: 2 x 1.0 HP - 12,000 RPM Motors capable of tilting 0° to 25° degrees with copy wheels; pneumatic positioning for (3) settings: Flush/bevel/radius trimming via precision digital indicators; goes from 3 mm PVC to thin tape through the Controller for quick setup. -- 2-Motor Corner Rounding:(2) 0.80 HP Independent motors that slide on THK guides; features of the "Round-K" (SCM patent) allow for the double function of both the simultaneous trimming and rounding operations. -- Top & Bottom Profile Scraping Unit: "RAS/K" Profile scrape station for: 3 mm PVC, pneumatic positioning with digital indicators; large dia. copy wheels for max. accuracy, and pneumatic in/out positioning. -- Buffing Unit: Top/bottom; 2 x 1/4 HP - 2,800 RPM motors, tilting up to 12°.Operator & Machine Control: -- "STARTOUCH" Controller with: 12" Touchscreen displays; capable of storing (100) programs.Machine automation by PLC function and encoder positioned in the panel feed track pinion.Diagnostics for a quick solution to errors; process statistics data, i.e., No. of pieces/edges and track feeding.Features & Complete with: -- (1) 2.0 HP Feed drive motor. -- 200 Hz Frequency inverter for all trimming unit.; -- Manual adjustable hold-down pressure beam -- Full sound enclosure cover and outboard panel support. -- Adjustable side support. -- Replaceable track pads. -- Digital inverter for electronic motor braking. -- Acoustical safety enclosure. -- Dust Collection: Working units are individually ported on the top of the safety enclosure for max. efficiency. -- Actual model is: SCM OLIMPIC K 600 T-ERL

SCM OLIMPIC K208ER EDGEBANDER WITH CORNER ROUNDING15/32" (12 mm) Max. edge cap., 2" max. (w/corner rounding only 1-3/4") banding height, 2-3/8" min. panel width and 6-5/16" min. length.Equipped with: -- Automatic strip & coil feed magazine w/Heavy Duty 3 mm PVC cap. guillotine. -- Teflon coated glue pot with glue roller application system complete w/automatic recycling device for unused glue. -- Digital thermostat adjustment for temperature control. -- 3-roll pressure unit w/pneumatic controls for all pressure rollers.Workstations: -- Double motor front & rear end trim (0.4 HP - 12,000 RPM motor ea.), tilts 0° - 15°, end trimmers mounted on 45° THK guide. -- Top & bottom fine/radius trimmer w/pneumatic positioning from control panel. -- Corner rounding units for leading & trailing edges. (2) 0.5 HP - 200 Cy Motors ea. -- Top & bottom PVC scraper for up to 5 mm radius. -- Top & bottom buffing unit (0.33 HP - 2,800 RPM motors). -- Hot air heating unit for PVC/ABS. -- Single 42 FPM fixed feed speed, 1 HP drive; heavy 3/4" drive chain with chain pads traveling on round & flat tracks.Complete with: -- Microprocessor for line control & glue temperature (can store up to 50 preset programs), swiveling control panel, pneumatic positioning of super finish, full cover sound enclosure, 200 Cy - 5 kW frequency inverter w/automatic motor brakes for all HF motors; includes used tooling. NOTE: Video of equipment was made in February 2021, prior to being decommissioned and placed in storage fully wrapped and ready for transport.

SCM OLIMPIC K 201 HFA Automatic Compact Edgebander, with 3 mm Max. Coiled Edgebanding Thickness & High Frequency MotorsSpecifications: -- Edgebanding thickness cap. (for both coil & strip) 0.4 - 3 mm (0.02" - 0.19"). -- Min. panel length for coiled edges (Min. width 200 mm) 140 mm (5.51"). -- Min. panel width for coiled edges 65 mm (2.56"). -- Panel thickness 8 - 40 mm (0.31" - 1.57"). -- Feed speed 9 MPM (29 FPM).Equipped with: -- Automatic adjustment of all units when panel thickness is changed. -- 20" Dia. Coil table. -- Automatic coil feed magazine, Manual strip feed. -- Teflon-coated glue pot. -- 1.2 mm (0.05") Cap. guillotine. -- Eye-level control, with GEFRAN "1000" LED Temperature controller. -- Adjustable feet.Workstations: -- Single-motor end trimming unit, with (1) 0.19 kW (1/4 HP) 12,000 RPM High-frequency motor & Copying device. -- Top & bottom flush trimming unit, with (2) 0.35 kW (1/2 HP) 12,000 RPM High-frequency motors and Front & Vertical copying devices.

SNX Edgebanding heater and storage system. For straight-line and contour edgebanders which: - Keeps banding at the perfect temperature - Softens banding, making it more pliableSNX TECHNOLOGIES COIL HUB - Edgebanding heater and storage system. For straight-line and contour edgebanders which: - Keeps banding at the perfect temperature - Softens banding, making it more pliable - Increases adhesion - Decreases delamination issues - Allows a cleaner guillotine cut - It lessens the chance of chipping when trimming. This CoilHub also keeps the coils contamination-free, keeps the edgebanding easily accessible right at the machine, and can store up to 20 coils.