SCM SANDYA - 40 M3 135, ...3-Head Wide Belt Sander 52" Width cap. Drum, Drum, Combination HeadHead Configuration:1st Head: Steel Contact 22 kW Pneumatic blowdown and alignment.2nd Head : Rubber Contact 18.5 kW Pneumatic blowdown and alignment.3rd Head: Combination Platen 15 kW Pneumatic blowdown and alignment.Note:The SCM sander does not have a brush. After the 3rd head, it has this pneumatic blow-off bar with multiple blow-offs running the length of the sanders width. Sander can be seen under power if needed.Specifications: -- 53" x 103" Abrasive belts with electronic tracking. -- All heads with abrasive belt grit compensation. -- Conveyor belt feed with dual feed speed, 5 HP motor. -- Automatic part thickness adjustment. -- Motorized thickness opening via (4) precision conveyor bed jacks with LED readout. --0" - 7-7/8" opening. -- Equipped with & Features -- Outfeed rubber covered holddown rolls or shoes on all heads. -- Motor load meters. --Infeed and outfeed conveyor extensions. -- WYE-DELTA soft start.Note: The SANDYA model "40" is more or less the same as the SANDYA "30" but more Heavy Duty.

SCMI SANDYA 20 ( 20 M2 135 ) Wide Belt Sander 2 Heads(2) Head 53" Width capacity , Drum, Combination HeadHead Configuration:1st Head: Grooved steel calibrating roller with 250mm (10") diameter with 42 HP main motor2nd Head: Combination head with 175 mm (7") grooved rubber finishing roller and finishing platen; with 30 HP main motor.Specifications: -- Working width 53 " rubber vacuum feed mat w/ vacuum blower (Small parts option) -- Grooved rubber coated pressure roller in first position for increased panel grip with multiple pieces. -- Maximum Work Piece Thickness 6.25". -- Min. Work Piece Length 17". -- Abrasive Belt Size 53" x 103". -- Compressed Air Requirements 5 CFM @ 80 PSI. -- Dust Outlets: 2 outlets @ 7.7 inches. -- Exhaust Requirements 3,600 CFM.Feed System: -- 3 HP variable speed feed -- Feed speed is from 15 FPM to 70 FPM. -- Automatic conveyor belt tracking. -- Infeed and outfeed table extensions with (2) support rollers each.Equipped with & Features: -- Automatic Table Positioning Device. -- Electronic digital thickness readout of work table position. -- Front and rear emergency stop buttons. NOTE: Some spec's need to be verified

SCMI SANDYA 3 Wide Belt Sander, (2) Heads37" Width cap. Drum, and Combination HeadHead Configuration:1st Head: 4" Dia. Steel Contact Drum 2nd Head: Combination head, rubber-covered contact roll, 4" dia. and 2" wide finishing platenSpecifications: -- Air jump platen with timers to control raise & lower of platen on leading and trailing panel edge. -- 30 HP motor driving both heads. -- 37" x 75" Abrasive belts with electronic tracking and pneumatic belt tensioning.Feed System; -- Infeed & outfeed spring loaded holddown rolls. -- Dual feed speed 15 & 30 FPM, 0.5 HP feed drive. -- 0 - 6" Motorized thickness opening via (4) precision conveyor bed jacks with LED readout.Equipped with & Features: -- Automatic part thickness adjustment. -- Motor load meters -- 21" infeed & outfeed conveyors each with (2) rubber-covered rolls -- (2) 5" Dust ports.Note from the seller: Lightly used machine in a two-man shop, primarily sanded our face frames for kitchen jobs, which amounted to a couple sets a month. works well, had an opportunity to purchase a bigger sander so this one is redundant.

SCM SANDYA 15S (3) Head Wide Belt Sander42" Width cap, Drum, Drum, Combination HeadHead Configuration:1st Head: Steel contact roll, 7" dia., 35 HP motor;2nd Head: Rubber-covered contact roll, 24 HP motor3rd head: Combination head, rubber-covered contact roll (45 Shore) and 3" wide finishing platen, 17.4 HP motor.Specifications: -- 43" x 103" Abrasive belts -- Electronic tracking & pneumatic belt tensioning, abrasive belt grit compensation. -- Conveyor belt feed with dual feed speed, 4 HP motor -- Automatic part thickness adjustment -- Motorized thickness opening via (4) precision conveyor bed jacksEquipped With & Features: -- LED readout, 0" - 6-1/4" opening. -- Infeed & outfeed spring loaded rubber covered hold-down rollers -- Motor load meters -- Infeed and outfeed roller conveyor extensions.

SCM SANDYA 3-RCS-95 Wide Belt Sander 9 ( 2 ) Heads36" width cap. Drum, PlatenHead Configuration1st Head : Contact Drum2nd Head : Combination HeadSpecifications: -- 1st Head: Contact roll, 4-3/4" dia.; -- 2nd Head: Combination head, with rubber covered contact roll, 4-3/4" and 2" wide finishing platen -- Both contact rolls & platen with cam height adjustments. -- 30 HP Motor driving both heads;Equipped with & Features -- 37" x 75" abrasive belts -- Electronic tracking and pneumatic belt tensioning. -- Infeed & outfeed rolls, -- Dual feed speed of 15 & 30 FPM, -- 0.5 HP feed drive -- Automatic part thickness adjustment -- Motorized thickness opening via (4) precision conveyor bed jacks with LED readout, -- 0" - 6-1/4" opening. -- Motor load meters, -- Infeed & outfeed conveyor roller extensions, (2) 5" dust ports.

SCM DMC TC 1350 RKP Wide Belt Sander ( 3 ) HeadsWidth cap. 53" , Drum, Combination Head, PlatenHead Configuration1st Head: 35 hp 9″ Spiral Drum2nd Head: 24 hp/30 hp dual RPM 7″ Spiral Drum/Combination Head W/Segmented Platen,3rd Head: 15 hp VFD driven multi speed Segmented Platen4th Station: Panel CleanerSpecifications -- 53″ working width, 656 hours of operation, --. Yes, it has (2) segmented platens. It’s from a custom shop and was utilized for very specific custom work and nothing else. -- 6.5″ thickness capacityEquipped with & Features -- Auto thickness calibration, -- Vacuum bed, -- 5 hp vfd controlled feed speed, and multiple modes. -- There is also a manual and (4) spare platens.Note: Only issue found , are lines on the LCD Screen (see pictures).

SCM Sandya 7 S Wide Belt Sander (2) Heads43" Width cap, Drum, Combination HeadHead Configuration1st Head: Contact roll, 6-1/4" dia., 25 HP motor; 2nd Head: Combination head, rubber-covered contact roll, 6-1/4" dia., and 2" wide finishing platen, 18 HP motor.Specifications: -- Great solid wood finish Sander. ÷ 43" x 75" or 85" Abrasive belts with electronic tracking & pneumatic belt tensioning. -- Conveyor belt feed with variable feed speed, 10 - 60 FPM, 3 HP motor, -- Automatic part thickness adjustment, motorized thickness opening with LED readout, -- 0" - 6-1/4" via (4) precision conveyor bed jacks.Equipped with & Feature: -- Infeed & outfeed spring loaded rubber covered holddown rolls on all heads, -- Motor load meters -- Infeed and outfeed conveyor extensions.

SHENG-SHING - SDM-15 ...Wide Belt Sander (Open Ended)15" Single Head Wide Belt Sander with open end for up to 30 " capacity. -- Sanding Head: 15" Wide (30" cap. with 2-pass); 8" Helically Grooved Rubber Covered Contact Roll with 7.5 HP Drive. -- Features: 0" - 6" Part thickness cap., 2-speed conveyor feed 12 or 16 FPM; 16" x 48" Abrasive belts with air tensioning, pneumatic abrasive belt tracking.

SHENG-SHING SDM-25 25" WIDE BELT SANDER1-Head, 24" width cap., rubber covered contact roll, approx. 10 HP motor. -- Abrasive belt size 25" x 48", with air tensioning and electronic abrasive belt tracking. -- 5-1/2" Max. height opening with manual raise & lower; variable feed speed drive. -- Complete with: Magnetic controls & dust outlet.

STATE B-4 OSCILLATING SPINDLE SANDER 1.5 HP Motor with manual switch, (9) spindles from 1/4" DIA to 4" DIA., 1,725 RPM spindle rotation, 20" x 24" table tilts 15° up and 45° down, table height 40". Also includes work light

STATE MODEL B-4 OSCILLATING SPINDLE SANDERSpecifications -- Tilting table design with pedestal floor mount --Table size.20" X 24" -- Table height 40" -- Table tilt 15° up, 45° down -- Spindle speed 1725 RPM -- Vertical oscillation 1-5/8" -- Oscillations/min.90 -- Lubrication...........Oil bath splash -- ÷ ÷Heavy duty 1/2 HP motor Maintenance free 1725 rpm TENV totally enclosed non-vented motor, rated for continuous operation, assuring long term dependable service. -- Safe operator controls Magnetic motor starter with overload protection for save installation. All controls are mounted for operator convenience. -- Operator friendly hand-wheel-tilting Engineered worm gear design allows table to be tilted 15 degrees up and 45 degrees down relative to spindle. Easy-to-read scale allows for accurate tilt determination before engaging locking device. A tapered pin locks the table during horizontal sanding operations. -- Safety features Magnetic motor starter with overload protection, safety labels, well-placed ergonomic controls, 3 throat rings to minimize table-to-spindle clearance, POSITIV-LOK spindles provide safe and quick means of changing spindles. -- Recently Cleaned, checked, electrical contacts cleaned, machine partially disassembled cleaned, re-assembled and tightened, and oil sight glass replacedWeight: 280 lbs.