ELGI EN07-125 10 HP Rotary Screw Compressor; 38 CFM @ 125 PSIG.Equipped with: -- Efficient air filtration system where air enters through a pre-filtered enclosure. -- After cooler is standard on all models to enable high efficiency TEFC, Super E, 10 HP motor operation up to 115°F ambient temperature.Complete with: -- "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Includes service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely.Includes: -- 3-Stage efficient air-oil separation (less than 2 PPM). -- Single door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety.Recommended option: F10104 / MICRO 50 Clean Resources F10104 / Micro 50 Clean Resources F10104 Oil/Water Condensate Separator - add;...$ 500

ELGI EG30-125 Rotary Screw Air Compressor; 40 HP - 170 CFM @ 125 PSIG40 HP Rotary Screw Compressor (Direct Drive); Air-End equipped with "eta-V" profile rotors. Equipped with: -- 4/5 Lobe combination designed to run at optimum speeds; low operating speeds for extended life, low maintenance and a reduced sound level; Intake Valve System with integrated blow down unit, solenoid controls & actuators designed for low losses. -- Optimal Capacity Control results in a direct saving on power consumption; air-oil separation with OSBIC process means oil-free air (1 PPM), per ISO standards and increasing the life of the separator element. -- Features: -- Efficient air cooling system; "Smart" cooling system maintains a lower temperature which increases the motor life, enables easy maintenance and the ducting is completely insulated internally from the other zones. -- Robust, reliable and able to perform at extreme temperatures - from cold to hot and from dry to extreme humid conditions. -- Complete with: -- Performance Control System's user-friendly intuitive backlit display for easy reading; remote monitoring through an RS485 connection; optimal pressure sensors monitor compressor internal pressure differences to optimize compressor maintenance. -- Includes: -- Phase Monitor, Auto Restart; custom designed, centrifugal type moisture separator with an automatic timer control drain which removes over 99% of bulk water from the compressed air.LIFETIME Air-End Warranty

ELGI EN07-125 10 HP ENCAP Rotary Screw Compressor w/Tank & Dryer; 38 CFM @ 125 PSIG.ELGI's 10 HP Rotary Screw Air Compressor w/20 CFM Refrigerated Dryer mounted on a 120 gal. receiver tank. -- Equipped with: 10 HP motor operation up to 115°F ambient temperature; "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely. -- Includes: 120 Gal. receiver tank, 40 CFM Refrigerated Air Dryer; single-door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety.Recommended option: -- [F10104 / MICRO 50] Clean Resources F10104 / Micro 50, Clean Resources F10104 Oil/Water Condensate Separator - Add $ 305Designed for smaller compressed air systems. This system was designed as an economical solution for small compressed air systems, up to 125 psi. Theproduct offerings also include a factory-installed and plumbed wall bracket, reducing installation time. Replacement cartridges provide easy, no messmaintenance and offer the lowest life cycle cost in the industry.

ELGI EG75-125 Rotary Screw Air Compressor; 100 HP - 453 CFM @ 125 PSIG100 HP Rotary Screw Compressor, 450 CFM @ 125 PSIG(Direct Drive); Air-End equipped with "eta-V" profile rotors. -- Equipped with: -- 4/5 Lobe combination designed to run at optimum speeds; low operating speeds for extended life, low maintenance and a reduced sound level; Intake Valve System with integrated blow down unit, solenoid controls & actuators designed for low losses. -- Optimal Capacity Control results in a direct saving on power consumption; air-oil separation with OSBIC process means oil-free air (1 PPM), per ISO standards and increasing the life of the separator element. -- Features: -- Efficient air cooling system; "Smart" cooling system maintains a lower temperature which increases the motor life, enables easy maintenance and the ducting is completely insulated internally from the other zones. -- Robust, reliable and able to perform at extreme temperatures - from cold to hot and from dry to extreme humid conditions. -- Complete with: -- Performance Control System's user-friendly intuitive backlit display for easy reading; remote monitoring through an RS485 connection; optimal pressure sensors monitor compressor internal pressure differences to optimize compressor maintenance. -- Includes: -- Phase Monitor, Auto Restart; custom designed, centrifugal type moisture separator with an automatic timer control drain which removes over 99% of bulk water from the compressed air.LIFETIME Air-End Warranty: Lifetime warranty subject to adherence to conditions outlined below. The scope of lifetime warranty will cover replacement of parts and free of cost labor for 120 months from date of start-up or 126 months from date of shipment from an ELGi warehouse, whichever occurs first. Parts only thereafter.Optional: [F10501 / CRP-500] Clean Resources F10501 / CRP-500 CRP-500 CFM Oil/Water Separator System (Includes DC Plus Manifold Installed) Order Number: 553-12-0047 The Next Generation Molecular Filtration System Compression-fit manifold for precise filtration control Timer drain for improved flow of condensate through the media bed Antimicrobial sanitation of discharge hose to prevent algae growth Twelve available inlets (increased from six) No maintenance or messy bag change-outs Cradle-to-grave warranty System monitoring services - Add ...$ 2,650

ELGI EN11-125 Tank Mounted Rotary Screw Compressor w/Refrigerated Dryer, 15 HP - 55 CFM @ 125 PSIGENCAP Series Screw Compressors:120 Gallon Tank Mounted with refrigerated dryer and filters - are designed to encapsulate all functional components and compressor within a common housing. With its small footprint, high reliability and low maintenance requirements, the compressors are ideal for all industrial applications where size, efficiency and cost matter.Equipped with & Features: -- 6 Year Airend Warranty -- Low Sound Enclosure -- Premium Efficiency NEMA motor w/F insulation -- TEFC Drive and Fan Motor -- High Ambient Oil Cooler for low operating temperature -- UL/cUL Certified Control Panel -- Controls & Indications: Microprocessor Controller includes -- Maintenance Schedules -- Pressure Transmitter -- Temperature Transmitter -- Auto Restart -- Remote Start / Stop -- Modulation and Load / Unload Controls -- Phase Monitor -- DCS Connection through Rtu/RS 485 PortRecommended option: F10105 / MICRO 100 Clean Resources F10105 / Micro 100 Clean Resources F10105 Oil/Water Condensate Separator - add $ 775

ELGI EGRD 500 Refrigerated Air Dryer (480 CFM)The ELGi EGRD 500 refrigerated dryer is designed to provide a constant 41ºF dew point and utilizes the latest advancements in refrigeration technology to provide low operating cost and years of trouble-free performance.The advanced “ALU Dry"; aluminum heat exchanger module enables the packaging of the pre-cooler, evaporator, separator, and reheater all in one compact unit. This reduces the size, weight and pressure drop associated with conventional exchangers and optimizes the overall performance and reliability of the dryer which ensures effective removal of condensed liquids regardless of flow.Features: -- Microprocessor Controls with Dew Point Display Indication -- All-In-One Aluminum Design Exchanger -- Low-Pressure Drop -- Ozone Friendly Refrigerant -- De-Mister Type Moisture Separator -- Environmentally Friendly Refrigerant -- Hot Gas Bypass for Constant Dew Point -- Extended Service Life -- Timer Drain Options Include: ELGI Pre-filter AF 0520P rated at 520 SCFM, 1-1/2" NPTPremium Filter Series is constructed from premium materials and features with ease of installation and service in mind. Filter elements have a unique push-fit, double O-ring design to ensure no contaminants get down stream. Features: -- High Quality Aluminum Construction -- Automatic Internal Float Drain -- Pop-up Filter Change Indicator

ELIO VALERI ELVAP 120 Copy Lathe. -- General data: 48" max. length cap., 7" max. dia. without steady rest, 3.93" max. dia. with steady rest, and up to 2.5" x 2.5" dia. with steady rest for square pieces; 0 - 39 FPM forward and 0 - 52 FPM return speed, 5.5 HP motor, 1,300 - 3,500 - 5,000 RPM; -- Features: Air/oil feed and copier, chain head stock drive, gate loading, pattern; pneumatic tail stock, automatic pneumatic control program.

HARRIS/SELCO - HLO-60AREB: Horizontal Auto-Tie Baler -- Motor: 2 – 100 HP. -- Cylinder: Rebuilt 12″. -- Hopper: 80″ Long. -- Hours of Operation: 14,000. -- Tons Per Hour/OCC: Up to 26 Tons. -- Includes 72″ MAYFRAN Steel Belt Feed Conveyor.

HARRIS-SELCO - HLO-608AR40: Open-End Auto-Tie Horizontal Baler -- Motor: 40 HP. -- 8" Cylinder with: 80" Stroke. -- Infeed opening; 45" x 60". -- Bale size: 48" x 40" x Variable. -- Bale weight: Up to 1,800 Lbs (OCC). -- Production capacity: Up to 6 T/Hr. -- Shear blade. -- Platen force 113,100 Lbs. -- Completely refurbished. -- Warranty: (180) Days Parts/Labor Warranty. -- Loaded onto your truck.

HASKO HSEM & HSFM End Matcher High-Speed Feed Through; Complete with Infeed conveyor, Transfer conveyor, End matcher, Outfeed conveyor and All ToolingSpecifications: -- The feed-thru system allows for continuous feeding of random length parts with any kind of profile. -- Width cap. 1" x 7"; length cap. 8-1/2" x 12'-0" lengths; 5/16"- 2" max. thickness cap.; -- Endmatcher with feed speed from 12 - 154 lugs per minute. -- Infeed powered roller conveyor 12" x 16', feeding singulator wheels for introducing lumber onto 9-strand infeed chain deck for the Endmatcher. -- Chain deck allows for spacing of boards for singulation between the spacing bars on the infeed deck system feeding the right-hand & left-hand stations. -- Infeed to tongue cut 19'-4" x 10', Crossover chain 14' x 10' to groove cut, outfeed chain 24'-0". Transport sprockets 50 pitch.Equipped with: -- Tongue first position and groove second; (3) heads per station all with VFD 5 HP motors at 6,000 RPM. -- Both the right and left-hand processing stations have a scoring, trim and profiling head. Includes: -- (One) Auxiliary infeed 8' x 7" ABC for infeed to Tongue unit with 3/4 HP variable speed drive -- (One) Auxiliary outfeed conveyor 13'-6" long x 7" wide slider belt with 3/4 HP variable speed drive to be installed behind the groove unit and extends out for grading station.Tooling: 12" in diameterNote: Specifications must be verified Still under power.

--AT AUCTION-- HEESEMANN KSA 8 CSD 80" Lacquer/Sealer Sander This is a Very Special "extra wide" HEESEMANN equipped with: HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 5/8" (16 mm) sense part configuration; pressure for each segment can be preprogrammed to provide less pressure on the outer edges, or more in the center if desired. The "CSD" computer control will hold a max. of (20) programs. Equipped with: Segmented Polishing Platen: Segments are computer controlled to conform to irregular shaped panels; sanding pressure on panel edges is adjustable. Platen will accept panel thickness variation up to 5/64" (2 mm). Dual speed motor: 26 & 31 kW (35 & 42 HP); abrasive belt speed: 10 + 20 MPS (33 + 66 FPM); abrasive belt size: 2,050 mm x 3,250 mm (80.7" x 128"); pneumatic air tension and tracking control. 250 mm Dia. Rotary Panel Cleaning Brush, 5 HP motor, 150 mm Outfeed Rotary Panel Cleaning Brush, and 2 HP motor. Additional Features: Vacuum bed assembly to ensure flatness of parts and feeding of small parts. Computer control and monitor, light indication of panel movement; electronic abrasive belt tracking. Feed System: Variable feed speed from 5 - 15 MPM (16 - 49 FPM); 4 kW (5 HP) feed motor; motorized thickness opening. NOTE: This Sander had a "Brand New" ...$ 17,000 display/control installed shortly before it was taken out of service in 2016. The machine has been in storage since that time.

HEESEMANN MFA-8 D Wide Belt Sander (4) Heads; 53" Width cap. Veneer/ Sealer Sanding Wide Belt.Great Lacquer/Sealer sander with: (2) Segmented polishing platen, (2) Orbital heads, (1) De-nibbing/Polishing brush.Head Configuration: Head 1: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 2: Segmented polishing platen, 5/8 wide segments CSD Control, Variable speed abrasive belt with inverter RPM control, 15HP motorHead 3: Orbital head with composite/dense fiber loading; 5HP motorHead 4: Orbital head with composite/dense fiber loading: 5HP motor(1) Brush Type head for de- nibbing and polishingSpecifications: -- LCD monitor with graphic display and key pad entry, 20 program capacity, -- Pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if required.Equipped with & Features -- Air blast abrasive belt cleaner on heads 1 & 2. -- Variable feed speed from 10 to 49 FPM via 2 HP feed drive. -- Motorized thickness opening 1/4" to 3-5/32" max. -- Rubber covered Infeed and out feed holddown rolls.

HEESEMANN LSM-8/3-OSR Wide Belt Finishing Sander, 52" and (3) Heads; Equipped with: (1) longitudinal segmented platen head. and (2) Orbital Platens -- 1st Head: Longitudinal segmented platen head. Segmented Polishing Platen, 20 & 27 HP dual speed motor. electronically controlled segments to conform to panel size,.2620 x 1350 mm (91.4 x 53.2") Sanding belt. - Equipped with HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 16 mm (5/8") sense part configuration; pressure for each segment, to eliminate sand through, can be pre-programmed to provide less pressure on the outer edges or more in the center if desired. The "CSD" computer control will hold a maximum of (20) programs. -- 2nd & 3rd Heads: OSR Dual orbital action head with (1) high-speed orbit on sanding pad, powered by 3 kW (4.5 HP) motor.Secondary oscillation movement of platens powered by 1.5 HP motor. Upstream and downstream vacuum chutes on each head for dust localized dust pickup.- Platens feature "quick change" abrasive material; Both orbital heads with variable speed inverter drives. -- Outfeed Rotary Brush with cleaning brush loading with single end adjustment , 6" max. dia., 3.4 HP motor. -- Variable feed speed from 13 to 82 FPM, 6.5 HP feed drive. -- Infeed and outfeed Ssissor Lift and Control box shown are not included. -- Motorized thickness opening 1/4" to 3-5/32" max. - -- Power Consumption: 63 KW, 75 Amps. -- Separate display console for CSD control.

HEESEMANN - LSM 8-5 RRRL, ...53" Wide Belt Sander53" Width cap.: Drum, Drum, Drum, and CSD® Pad.Head Configuration:• Unit 1 - Longitudinal Sanding Unit: Steel contact roller, helically grooved. - Single-speed 48 HP motor, electronic braking.• Unit 2 - Longitudinal Sanding Unit: Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking.• Unit 3 - Longitudinal Sanding Unit:- Rubber-covered contact roller, helically grooved. - Single-speed 35 HP motor, electronic braking, bi-directional drive.• Unit 4 - Longitudinal Sanding Unit: CSD® Segmented pad system, 2-speed 20/26 HP motor, electronic braking.• Unit 5 - Panel Cleaning Brush: Fiber trimming, 2.3 HP Motor.Specifications: -- Working height: 880 mm (34.64"). -- Workpiece thickness: 3 mm to 150 mm (1/8" to 6"). -- Working width: 1,300 mm (51-1/8"). -- Longitudinal belt: 1,350 x 2,620 mm (53" x 103"). -- Machine voltage: U.S. Electrics 480 Volts, 3-Phase, 60 cycles.Constant Pass LineController: -- Industrial PC. -- TFT Color touchscreen. -- Windows® Operating System. -- (100) Memory addresses for: • CSD® sanding pressure. • Sanding start/stop. • Sanding belt speeds. • Grit sequence indication. • Sanding belt selection - "ON/OFF". • 1-Button sequenced starting for all motors.RS-232 Serial port.RJ-45 LAN Port.Modem with software licenses.For All additional, detailed specs, select the "View Literature" link .

54" 3-Head Orbital Sander, For abrasive belt cross-grain scratch removal with (3) Orbital Platen Heads & (1) Rotary Brush Head Configuration: 1st, 2nd, & 3rd Heads: Each with 5" W Platen, Dual orbital action, High-speed orbit on sanding pad with 3 kW (4 HP) Motor, Secondary oscillation with 1-1/2 HP Motor, "Quick-change" abrasive material, Inverter drive; Rotary Brush: 6" Maximum diameter, 3-1/2 HP Motor, Brush loading, Ionization bar for final fine dust collection Vacuum conveyor bed with 10 HP Blower motor, Inverter-controlled variable speed drive with 4 HP Motor & Variable feed speeds 15 - 66 FPM, Automatic conveyor belt tracking, Automatic parts thickness, with 1/8" - 4-5/8" Thickness range & Programmable height adjustment, (4) Screw jacks PC-based control, Windows XP, Touchscreen monitor, Infeed & outfeed spring-loaded hold-down rolls, Infeed hand safety stop, outfeed emergency stop, Digital motor load meters, High-efficiency dust extraction NOTE: Machine is currently in storage.

HEESEMANN - KSA 8 CSD, ...Lacquer/Sealer Sander w/80" Belt WidthThis is a Very Special "extra wide" HEESEMANN equipped with: HEESEMANN's patented "CSD" selective pressure adjustment system, sensors placed every 5/8" (16 mm) sense part configuration; pressure for each segment can be preprogrammed to provide less pressure on the outer edges, or more in the center if desired. The "CSD" computer control will hold a max. of (20) programs.Equipped with: -- Segmented Polishing Platen: Segments are computer controlled to conform to irregular shaped panels; sanding pressure on panel edges is adjustable. -- Platen will accept panel thickness variation up to 5/64" (2 mm). -- Dual speed motor: 26 & 31 kW (35 & 42 HP); abrasive belt speed: 10 + 20 MPS (33 + 66 FPM); abrasive belt size: 2,050 mm x 3,250 mm (80.7" x 128"); pneumatic air tension and tracking control. -- 250 mm Dia. Rotary Panel Cleaning Brush, 5 HP motor, 150 mm Outfeed Rotary Panel Cleaning Brush, and 2 HP motor.Additional Features: -- Vacuum bed assembly to ensure flatness of parts and feeding of small parts. -- Computer control and monitor, light indication of panel movement; electronic abrasive belt tracking.Feed System: -- Variable feed speed from 5 - 15 MPM (16 - 49 FPM); 4 kW (5 HP) feed motor; motorized thickness opening.NOTE: This Sander had a "Brand New" ...$ 17,000 display/control installed shortly before it was taken out of service in 2016. The machine has been in storage since that time.

Heesemann HSM Features:Thickness adjustment of sanding heads from 3 to 160 mm (0.118 to 6.3") -- Constant working height of 880 mm (34.6") -- A constant pass line features 3 mm per second adjustment -- An over-thickness control system -- Emergency stops located at machine infeed and outfeed -- Integrated switch cabinet -- Control for excessive workpiece heightHeesemann's HSM transport conveyor features:Electronic variable speed infeed conveyor drive -- Controllable feed speed by an industrial PC -- A transport belt with ½" diamond profiles and one-piece construction -- Automatic tensioning & trackingPress-on RollerA 50 mm roller at the infeed of the machine to hold down thin and warped workpieces with thefollowing features:Spring loaded and adjustable -- Includes workpiece over-thickness controlHigh Performance Vacuum Hold DownEquipped with a high-performance vacuum hold down system for safe movement of workpiecesshorter than 500 mm (20") in feed direction including integrated ventilator in machine base. Canbe turned on or off via controller or in individual programs. The vacuum blower is a high pressureblower, offering optimal performance with minimal power requirements due to the fandesign, helping provide excellent suction with low power consumption.Emergency StopIndustrial PC, This sander is equipped with a 15" high resolution touch screen / industrial PC and features:High resolution display -- Windows® embedded operating system -- Pendent mounted with adjustable viewing position -- Ethernet connection -- Configured as web address for easy network access -- Automatic on-screen diagnostics -- Metric or English input -- 1000 memory addresses -- Alpha/numeric format -- Password protected -- Digital keypad input -- Workpiece thickness -- Conveyor belt feed speed -- Sanding pressures -- One button startRoller Table For infeed500mm long (20";) -- Height adjustableHead 1: DB-S Head – Rotating Planetary Sanding Unit:10 driven discs with quick changing device -- Rotation in both directions -- Central height adjustment -- 7.5 kW (10 Hp) motor to power the discs -- 1.5 kW (2 Hp) motor gear box -- Brush trimming: Flex Trim -- Tool Diameter: 150 mm (6";) -- Other brush discs available on demand -- One set of discs is included with sanding headHead 2: DB-S Head – Rotating Planetary Sanding Unit:10 driven discs with quick changing device -- Rotation in both directions -- Central height adjustment -- 7.5 kW (10 Hp) motor to power the discs -- 1.5 kW (2 Hp) motor gear box -- Brush trimming: Flex Trim -- Tool Diameter: 150 mm (6";) -- Other brush discs available on demand -- One set of discs is included with sanding head Brush trimming: Flex Trim -- Tool Diameter: 150 mm (6";) -- Other brush discs available on demand -- One set of discs is included with sanding headTechnical Specifications:Working height: 880 mm (36.2") --Workpiece thickness: 3 mm to 160 mm (0.118" to 6.29") --Working width: 1300 mm (51.2") --Transport belt speed: 3 mpm

Heesemann MFA6 (3) Head Wide Belt Sander, 53" width cap. Drum Drum, Segmented platenHead configuration1st Head: Steel contact roll, 30 HP motor2nd Head: Rubber covered contact roll, 20 HP motor3rd Head: Segmented polishing platen, electronically controlled segments to conform to panel size, 20 HP motor4th Station: Outfeed rotary panel cleaning brush, 2 HP motor.Specifications -- Platen head equipped with: HESSEMANN's Patented "CSD-32" selective pressure adjustment system; sensors placed every (32 mm) sense part configuration, pressure for each segment can be pre-programmed to provide less pressure on the outer edges or more in the center if desired. -- Both contact rolls with NC positioning and auto grit compensation, automatic line control for platen independent of feed speed determines automatically the correct part in time for the pressure segmentEquipped with & Features -- Outfeed rotary panel cleaning brush, 2 HP motor. -- 55" x 103" Abrasive belts on all heads with abrasive belt air cleaners, "ICP" control for all sander functions, (20) programs storrage. -- Variable feed speed from 10 - 49 FPM, 3 HP feed drive with inverter control. -- Vacuum conveyor bed assembly with suction fan and )motor mounted in machine base, motorized thickness opening 0" - 5-7/8" w/digital readout, constant passline of conveyor bed assembly 35" height.NOTE Some Spec's need to Varified

Heesemann MFA Impression 4-Head Wide Belt SanderSpecifications -- Working Width: 53" (1350mm) -- Workpiece Thickness: 0.118" to 6" (3mm to 160mm) -- Working Height: 36.2" (880 mm) -- Wide Belt Size: 103" x 55" (2620mm x 1400mm) -- Cross Belt Size: 189"x6" (4800 x 150mm) -- Variable Feed Speed: 10-50 FPM (3-15 mpm) -- Vacuum Bed for Safe Movement -- os Workpieces Shorter than 19.7" (500mm)Head Configuration1st Head: Cross Sanding Unit Heesemann's Cross Sanding Head Unit Removes Fiber from Solid Wood or can be used to Remove Tape from VeneerSanding Belt Speed:6.5 - 65 FPS (2-20 m/s)Drive Motor: 23HP (17kW)2nd Head: Longitudinal Sanding Unit Sanding Belt Speed: 6-60 FPS (1.8-18 m/s) Drive Motor: 23HP (17kW)3rd Head Longitudinal Sanding Unit Sanding Belt Speed: 6-60 FPS (1.8-18 m/s) Drive Motor: 23HP (17kW)4th Head: Lef Head w/ Internal Pressure Belt Enhanced Finish Let Head Features an Inner Chevron Belt to Allow for Fine Sanding of Workpiece Sanding Belt Speed w/o Pressure Belt: 6-60 FPS (1.8-18 m/s) Sanding Belt Speed w/ Pressure Belt: 6-30 FPS (1.8-9 m/s) Drive Motor: 23HP (17kW)Equipped with & Features --All Heads Variable Speed Belt equipped with Inverter Motor -- CSD® segmented pad system on all Heads -- A pinch roll system, rubber covered and adjustable -- An automatic infra-red belt control -- Servo cross belt tracking adjustments, for quick and easy belt centering when loading -- Workpiece Blasting Device -- Rotating Compressed Air Nozzles for Blasting Workpiece Surface -- LED Lights on Belt Change Side -- Ionization Bar from Above that Helps Reduce Static Charge -- Pneumatic Conveyor Belt Cleaning -- Dust Extraction: Approx 6000 CFM -- Compressed Air: 100 cfm @ 100 psi -- Power: 480 Volt, 3 Phase, 60HZ

HEIAN FP-151-MC-2113 5-Axis CNC MachineFor high speed & precision routing/trimming & sizing wood and composite parts.Equipped With: -- (2100 mm) x (1,300 mm), moving table, fixed bridge style machining center; mahogany vacuum table. -- 3.7 kW, NT 30 Type ATC spindle, variable speed from 2,000 - 18,000 RPM with 8-position tool carousel. -- FANUC "16i CNC Control, 10.4" LCD , RS-232C/PCMCIA (memory card). Features: -- 5-Axis simultaneous motion, M & G code programming, inch or metric operation. -- Working Axes Stroke & Speed: X-Axis (2,600 mm) 60 m/Min; Y-axis (1,600 mm) 40 m/Mn; Z-axis (800 mm) 20 m/Min -- C-axis +/- 270°; B-axis +/- 110°; C-axis travels at 4,000°/Min and B travels at 4,000°/Min. -- Complete with assorted tool holders.