MURPHY-RODGERS - MRSE-24: RAL Dust Collector; loaded with features. -- General Data: Self-contained baghouse, approx. 15,000 CFM with 1,913 sq./ ft. of filter area based on: 7.8 to one Air-to-Cloth-Ratio. -- Fan/Motor: 40 HP BALDOR motor; 22" dia. inlet; primary separator built into the unit; secondary separation of fine particles by filter bags. -- Equipped with: 16" Dia. bottom dump outlet controlled by a Rotary Air Lock with: Approx. 18" dia. discharge outlet. -- Complete with: (2) Electric motor driven automatic bag shakers; angle frame truck height support stand with walkway platform and full height ladder to access top of unit.Fan/motor mounted on top of the collector. -- Includes: Magnetic starter. control panel; silencer; explosion doors. -- Approx. dims.: 84" x 85" x 32' High; 6,100 Lbs.

MURPHY-RODGERS - MRT-12 AS, ...Dust Collector (Interior) -- Specifications:Motor: TEFC 10HP, 230/460, 3 PH; Inlet diameter: 12"; Collection Outlet Opening: 11″; (1) Four (4) bag unit; 3,500 CFM. -- Floor space: 62" Wide x 102" deep x 118" high. -- NOTE: (4) Barrels (as pictured) are included!

MURPHY-RODGERS - MRSE-14-RAL: Baghouse Dust CollectorSpecifications: 14" Inlet dia.; 4,836 CFM; (63) bags with: 520 Sq./ft. filter area; 9.3:1 air-to-cloth ratio; 20 HP fan motor; primary separator built into unit; secondary separation of fine particles by filter bag section; -- Equipped with: -- Rotary Air Lock. -- Fully automatic shaker controls with: Electric shaker as standard; consists of panel box with shaker starter; transformer for 115 V circuitry; solid-state timer for fan deceleration & shaking cycle. -- All necessary relays and internal wiring inside the panel box.

MURPHY-RODGERS - HEC-216-S/10: 33,000 CFM Continuous Duty Automatic Self-Cleaning Pulse Jet Baghouse Dust CollectorEquipped with: -- (216) 5" Dia. x 10' L Cloth filter bags for a total of: 2,827 sq/ff. of filter area. -- (2) 42-1/2" W x 68" H & (2) 40-1/2" x 68" H Top access doors. -- (3) Front & (2) side 27" W x 54" H Filter access doors. -- (2) Square cone bottom hoppers each with: 25" x 25" Discharge openings. -- System utilizes: (2) 4-1/2’ x 6’ x 4’ H Waste containers (NOT included). -- CHICAGO 100 HP - 1,780 RPM Roof Mounted Blower with: 41"; Dia. inlet. -- Motorized dampers for winter & summer modes. -- Winter mode: Directs air back into building, reducing heat loss. -- Summer mode: Directs air outside, cooling building. -- Electrical controls (as pictured). VFD needs to be repaired or replaced.Complete with: -- Spare Filter Bags.NOTE: Installed Used in 2016 with "New" 100 HP motor, new bearings in blower & "New" spring mounts.

PRESTO XL60-60 Scissor Lift6,000 Lbs. load capacity for evenly balanced load.Specifications: -- 10" Lowered height. -- 60" Travel to raised height of 70". -- 30 Seconds travel time. -- Hinged platform for access to cylinders and internal power unit in the collapsed position. -- 48" W x 96" L platform size, base 24" W x 86" L. -- 3/4" Steel plate scissor legs. -- Heavy Duty hydraulic cylinders with chrome-plated rams. -- Lifetime lubricated bearings on all rollers and pivot points. -- Electro-hydraulic 3.2 HP motor. -- Standard hand control pendant. -- Standard safety velocity fuses. -- Safety maintenance device.

PRESTO P3-AA ROUND PNEUMATIC AIRBAG LOAD LEVELERTurntable top with easy turning anti-friction bearings allows users to spin loads so they are always working from the near side without having to walk around the unit.Specifications: -- Automatic positions loads between 9-1/2" and 27-3/4" -- Small base allows workers to stand up close to the P3 at any position -- Stable design requires no floor lagging -- Build fork pockets for easy lagging, -- Load capacity 4,000 Lbs -- Raised height 27-3/4" -- Lowered height 9-1/2" -- Overall base 36" W x 36" L -- Turntable diameter 43-5/8" -- Shipping weight 450 Lbs

PRO-EDGE TECHNOLOGY SQUEEZETIGHT CASE CLAMP (AUTOMATIC FEED THROUGH): -- Specifications:The SqueezeTight automatic hydraulic case clamp does the work for you. The vertical pressing system with motors & independently controlled crossbars move according to the size of the piece to be pressed, mobile parts slide along linear bearings and guides. -- Operating Cycle;Once the piece of furniture is assembled on the preparation bench the operator starts the automatic cycle and the carcass enters the machine.The reading devices automatically determine the length and height of the workpiece and send this information to the PLC which positions the mobile head and the conveyor and stops the carcass in position. The beam automatically moves to the preset position.Each of the mobile heads are fitted with: (2) RH & (2) LH Horizontal pressure beams + (4) stationary & (1) adjustable top pressure clamps.The Clamping Cycle is 100% programmable & pressing is by a 10 HP (7.5 kW) Hydraulic pump system.The in-out-cross transfer powered belt conveyors are driven by "SIEMENS" AC brushless motors. -- Working Capacity:9.8" - 89.7" (250 - 2,280 mm) working width/length, 9.8" - 42.9" (250 - 1,090 mm) working height, 9.8" - 25.9" (250 - 660 mm) working depth. -- Positioning Speed:32.8 - 131.3 FPM (10 - 40 MPM) Variable speed controlled by programmable inverter. -- The carcass transfer system is located at the bottom of the bed and consists of an electro-welded steel structure on which a closed loop belt is driven by an inverter-controlled "SIEMENS" motor. -- Operator Interface:Automatic cycle control from onboard "HMI" Touch Screen control + "DELTA" VFD's & PLC with adjustment for all clamping aspects. Clamping pressure strength up to 1,200 PSI over-all. -- Complete with:(1) 98" Long powered in-feed conveyor belt with alignment guideways, (1) 98" Long powered cross-feed conveyor belt with alignment guideways & (1) 98" Long powered out-feed conveyor belt. Parameter Safety Light Curtain System. -- NOT included:Cost for Delivery, installation, and training (please call for quotes). -- Actual Model is PRO-EDGE TECHNOLOGY SQUEEZETIGHT

4-Station Profile ShaperSpecifications: -- 6" Chain drive with non-marking rubber top pads traveling on a hardened and ground precision dia. 5/8" round rods, Top pressure beam driven, Heavy duty fabricated transporter frame, Forward and reverse mode and block mode for creating sanding tools -- Precision X & Y axis mounting stands, 60° rotating tilt on mounting stands with positive lock, Independent activation control at each station, Adjustable infeed fence system, All dust hoods and guards, 2 HP AC variable speed gear drive 5 to 60' per min.Workstation 1: 3.5 HP TEFC Saw Arbor Motor, 1" Dia. Spindle, Dust Hoods with 4" outlet, Mounted on precision X & Y slides Workstation 2 & 3 - Belt Sanding Unit: 2 HP AC motor drive, Air belt tension system, Independent belt tracking system, Air activated sanding pad with touch control, 2" sanding belt width, Guards and Dust hoods with 4" outlet Workstation 4 - Wheel Sanding Unit: 3" HP variable speed (0-3,400 RPM) AC TEFC drive motor, 1" or 1.25" arbor 3.5" long, Dust Hood with 4" dia. outlet, Mounted on precision X & Y slidesSPECIAL NOTE: Needs New PLC or wire for traditional controlsNOTE: Above specs are taken from literature and thought to be accurate.

PROFILEMATIC 503 PROFILE SANDER3-Head feed through, sands from top at adjustable angles narrow moulding type parts as well profiled edges on panels.Equipped with: -- (3) Top VPS vibrating air-loaded sanding units, 0.5 HP vibrating motor ea., sanding heads have (2) pneumatic cylinders for sanding pressure control and oscillate with 1/2" stroke on dust-protected round guides, variable vibration speed from 200 - 1,800 RPM; adjustment range of 120ø to conform to profile, equipped with air shower to clean workpiece & sandpaper automatically. -- Part transport is achieved by a 4-1/2" wide linatex coated conveyor belt system, "quick adjustment" holddown wheels & fence system, variable feed speed 0 - 35 FPM powered by a 0.25 HP DC gear drive (forward & reverse feed mode). -- Each sanding head with its own controls for manual raise & lower, pressure control and vibrating speed. Profile width approx. 1/2" min. to 4" max., material feed through thickness up to 5"; support fences for up to 10" moulding width.

Make an offer - Machine is in an Ex-Factory Liquidation. 4-Station Profile Shaper Specifications: 6" Chain drive with non-marking rubber top pads traveling on a hardened and ground precision dia. 5/8" round rods, Top pressure beam driven, Heavy duty fabricated transporter frame, Forward and reverse mode and block mode for creating sanding tools Precision X & Y axis mounting stands, 60° rotating tilt on mounting stands with positive lock, Independent activation control at each station, Adjustable infeed fence system, All dust hoods and guards, 2 HP AC variable speed gear drive 5 to 60' per min. Workstation 1: 3.5 HP TEFC Saw Arbor Motor, 1" Dia. Spindle, Dust Hoods with 4" outlet, Mounted on precision X & Y slides Workstation 2 & 3 - Belt Sanding Unit: 2 HP AC motor drive, Air belt tension system, Independent belt tracking system, Air activated sanding pad with touch control, 2" sanding belt width, Guards and Dust hoods with 4" outlet Workstation 4 - Wheel Sanding Unit: 3" HP variable speed (0-3,400 RPM) AC TEFC drive motor, 1" or 1.25" arbor 3.5" long, Dust Hood with 4" dia. outlet, Mounted on precision X & Y slides SPECIAL NOTE: Needs New PLC or wire for traditional controls NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

PROFILEMATIC - BF-400: Solid Surface Sand/Buff -- FeaturesPatented Rotary Orbital Sanding/Buffing System. For sanding & buffing solid surface countertops up to 10' long x 40" wide; with or without sink bowls or cove backsplashes to a matt finish in approx. (3) minutes. -- Quickly programmed. Speed of the top through the machine; speed of the randomly orbiting sanding heads; stroke distance of the sanding heads. -- Operator places the workpiece on a feed through Conveyor System; top automatically feeds through the machine and is sanded with different grades of sandpaper or buffing material and exits the machine as a finished product. -- SpecificationsMaterial Width: 40″; material length: Unlimited; material thickness: 12″ +/-; (3) Sanding Stations; (18) sanding heads; sanding pad type: PSA. -- Equipped with(45) 5″ Diameter Sanding Discs; Infeed & Outfeed Conveyors; ALLEN-BRADLEY "PanelView 300" Controller. -- Actual model: PROFILEMATIC - SURFACE MASTER BF-400 & Made in the USA!

PROGRESS PMC-264 Stroke SanderSpecifications: -- 8' x 30" Sliding table (on ball bearing steel rollers), 30" table travel; -- Manually operated stroker pad travels on ball bearings; large hand wheel for manual raise-and-lower of table for up to 24" vertical opening -- 5 HP - 1,750 RPM TEFC main motor. -- (2) 10" Dia. pulleys x 6-1/4" face, drive pulley rubber covered; -- 6" Wide x 264" long abrasive belt, abrasive belt speed 4,300 SFPM. -

PROGRESSIVE - Model SB/D 31, ...Dip Chain Gang Rip Saw.Specifications: -- 31" Cap. arbor with: Pneumatic arbor lock, 14" max. dia. tooling, -- 5" max. motorized thickness adjustment; 22" min. length for glue joint accuracy, 6" throat depth to fence side of blade. -- (1) 31-1/2" Saw sleeve with: Double-keys arranged for 3-1/8" bore saw blades. -- Equipped with: 75 HP - 3,600 RPM TEFC -- Direct drive motor, arbor with disc brake & load meter; 2-3/16" dia. turned, ground & polished saw arbor with outboard bearing; motorized vertical adjustment of arbor. -- Feed & chain: 34" Wide feed bed, -- 5 HP variable feed drive, feed speed from 30 - 150 FPM; adjustable jam protection. -- Dip bed carried on 2-1/2" pitch hardened double V-chain, extruded structural aluminum feed bed slats with replaceable Equipped with & Features -- "Safety Orange" polyurethane inserts; oil mist lubrication for extended chain life. -- (2) Infeed & (2) outfeed 4" dia. air loaded overhead pressure rolls; full width air loaded laminated bed holddown plate at saw arbor with +/- 1/4" thickness variation with pressure adjustment -- Pressure rolls & bed plate unit with manual height adjustment. -- Anti-kickback Finger System with: (1) Lower & (2) upper on infeed, (1) upper between feed rolls, and (1) upper assembly on outfeed. -- 5" Dia. dust outlet on upper infeed & 8" dia. dust outlet in upper outfeed; control panel mounted on infeed; saw sleeve and spacers. Note: Includes One Sleeve with a Collection of Spacers -- Owner's Manual Included -- Machine can be purchased As Is with a condition report (available on request), or you have it gone through ( As Is will be at a reduced price )

PTR - 2507-HD, ...2-1/2 Yard Stationary CompactorSpecifications: -- Charge box capacity: 2.5 Cu/Yd -- Clear top opening (L x W): 54-1/2" x 60" -- Total normal force: 59,376 Lbs -- Cylinder bore: 6" -- Cylinder rod: 3-1/2" -- Capacity per hour: 63 Cy/Hr -- Average cycle time: 57 SecEquipped with: -- Heavy-Duty structural steel components -- 3-Button controls

CASADEI (PUTSCH-Branded) EBP-950 PMCR Automatic Edgebander, New, Never Used, with Pre-Mill & Corner RoundingSpecifications: -- Edgebanding thickness: 0.4 - 3 mm (0.02" - 0.12") Coil, 0.4 - 5 mm (0.02" - 0.20") Strip with Manual feed. -- Panel thickness 8 - 45 mm (0.31" - 1.77"), Min. panel width 95 mm (3.74"), & Min. panel length 110 mm (4.33"). -- Feed speed 9 MPM (29 FPM).Equipped with: -- Pre-Mill Unit, with (2) 0.75 kW (1 HP) - 12,000 RPM - 200 Hz Motors, Counter-rotation, (2) 60 mm Dia. x 52 mm H (2.36"; Dia. x 2.05"; H) Diamond cutterheads, Max. milling adjustment 2 mm (0.08"), & Dedicated extraction system with Blower. -- Anti-Adherence Spray Unit. -- Infrared lamp. -- PURE (PUR & EVA) Hot melt gluing system, with Teflon-coated glue pot with (6) 1,315 W Heating elements with (4) in Glue pot, (1) in Turret & (1) in Glue spreading roller, Thermostatic glue control, Automatic standby & Temperature display, and Automatic glue drainage. -- Pneumatically-operated guillotine. -- Pressure section, with (1) Large driven & (2) Small idler rollers. -- Feed chain, with Scratch resistant, non-slip rubber pads. -- Top pressure beam, with (2) Rows of rubber rollers. -- Safety enclosure. -- PLC Control, with ETOUCH 7" Backlit LCD touchscreen display, 99-Program Storage, & Diagnostics.Workstations: -- Front & Rear End Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, & (2) 80 mm (3.15";) Knives. -- Top & Bottom Flush/Bevel/Radius Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motors, 75 mm (2.95") Dia. Cutters with Disposable knives, 2 - 3 mm (0.08" - 0.012") Radii, & 15° Bevel. -- Corner Rounding Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, 50 mm (1.97";) Diamond cutterheads, 50 mm (1.97";) Vertical/Horizontal copiers for profiling straight, curved, & beveled edges, & PLC-selectable front, rear, or complete panel processing. -- Edge Scraping Unit, with 2 mm (0.08";) Cutters, -- Top & Bottom Glue Scraping Unit, with 120 mm (4.72";) Vertical disc copier. -- Top & Bottom Buffing Unit, with (2) 0.13 kW (0.17 HP) - 1,400 RPM Motors. -- Polishing Spray Unit, PLC-Controlled, with (2) Sprayers.NOTE: Sold "As Is" Without Warranty!

CASADEI (PUTSCH-Branded) EBP-950 PMCR Automatic Edgebander, New, Never Used, with Pre-Mill & Corner RoundingSpecifications: -- Edgebanding thickness: 0.4 - 3 mm (0.02" - 0.12") Coil, 0.4 - 5 mm (0.02" - 0.20") Strip with Manual feed. -- Panel thickness 8 - 45 mm (0.31" - 1.77"), Min. panel width 95 mm (3.74"), & Min. panel length 110 mm (4.33"). -- Feed speed 9 MPM (29 FPM).Equipped with: -- Pre-Mill Unit, with (2) 0.75 kW (1 HP) - 12,000 RPM - 200 Hz Motors, Counter-rotation, (2) 60 mm Dia. x 52 mm H (2.36"; Dia. x 2.05"; H) Diamond cutter-heads, Max. milling adjustment 2 mm (0.08"), & Dedicated extraction system with Blower. -- Anti-Adherence Spray Unit. -- Infrared lamp. -- FLEX Interchangeable gluing system, with Teflon-coated glue pot with (6) 1,315 W Heating elements with (4) in Glue pot, (1) in Turret & (1) in Glue spreading roller, Thermostatic glue control, Automatic standby & Temperature display, and Automatic glue drainage. -- Pneumatically-operated guillotine. -- Pressure section, with (1) Large driven & (2) Small idler rollers. -- Feed chain, with Scratch resistant, non-slip rubber pads. -- Top pressure beam, with (2) Rows of rubber rollers. -- Safety enclosure. -- PLC Control, with ETOUCH 7" Backlit LCD touchscreen display, 99-Program Storage, & Diagnostics.Workstations: -- Front & Rear End Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, & (2) 80 mm (3.15";) Knives. -- Top & Bottom Flush/Bevel/Radius Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motors, 75 mm (2.95") Dia. Cutters with Disposable knives, 2 - 3 mm (0.08" - 0.012") Radii, & 15° Bevel. -- Corner Rounding Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, 50 mm (1.97";) Diamond cutter-heads, 50 mm (1.97";) Vertical/Horizontal copiers for profiling straight, curved, & beveled edges, & PLC-selectable front, rear, or complete panel processing. -- Edge Scraping Unit, with 2 mm (0.08";) Cutters, -- Top & Bottom Glue Scraping Unit, with 120 mm (4.72";) Vertical disc copier. -- Top & Bottom Buffing Unit, with (2) 0.13 kW (0.17 HP) - 1,400 RPM Motors. -- Polishing Spray Unit, PLC-Controlled, with (2) Sprayers.NOTE: Sold "As Is" Without Warranty!

CASADEI (PUTSCH-Branded) EBP-950 PMCR Automatic Edgebander, New, Never Used, with Pre-Mill & Corner RoundingSpecifications: -- Edgebanding thickness: 0.4 - 3 mm (0.02" - 0.12") Coil, 0.4 - 5 mm (0.02" - 0.20") Strip with Manual feed. -- Panel thickness 8 - 45 mm (0.31" - 1.77"), Min. panel width 95 mm (3.74"), & Min. panel length 110 mm (4.33"). -- Feed speed 9 MPM (29 FPM).Equipped with: -- Pre-Mill Unit, with (2) 0.75 kW (1 HP) - 12,000 RPM - 200 Hz Motors, Counter-rotation, (2) 60 mm Dia. x 52 mm H (2.36"; Dia. x 2.05"; H) Diamond cutterheads, Max. milling adjustment 2 mm (0.08"), & Dedicated extraction system with Blower. -- Anti-Adherence Spray Unit. -- Infrared lamp. -- FLEX Interchangeable gluing system, with Teflon-coated glue pot with (6) 1,315 W Heating elements with (4) in Glue pot, (1) in Turret & (1) in Glue spreading roller, Thermostatic glue control, Automatic standby & Temperature display, and Automatic glue drainage. -- Pneumatically-operated guillotine. -- Pressure section, with (1) Large driven & (2) Small idler rollers. -- Feed chain, with Scratch resistant, non-slip rubber pads. -- Top pressure beam, with (2) Rows of rubber rollers. -- Safety enclosure. -- PLC Control, with ETOUCH 7" Backlit LCD touchscreen display, 99-Program Storage, & Diagnostics.Workstations: -- Front & Rear End Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, & (2) 80 mm (3.15";) Knives. -- Top & Bottom Flush/Bevel/Radius Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motors, 75 mm (2.95") Dia. Cutters with Disposable knives, 2 - 3 mm (0.08" - 0.012") Radii, & 15° Bevel. -- Corner Rounding Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, 50 mm (1.97";) Diamond cutterheads, 50 mm (1.97";) Vertical/Horizontal copiers for profiling straight, curved, & beveled edges, & PLC-selectable front, rear, or complete panel processing. -- Edge Scraping Unit, with 2 mm (0.08";) Cutters, -- Top & Bottom Glue Scraping Unit, with 120 mm (4.72";) Vertical disc copier. -- Top & Bottom Buffing Unit, with (2) 0.13 kW (0.17 HP) - 1,400 RPM Motors. -- Polishing Spray Unit, PLC-Controlled, with (2) Sprayers.NOTE: Sold "As Is" Without Warranty!

PUTSCH-MENICONI KOPERNIC 4,200 x 2,200 mm CNC Vertical Machining Center, New with Parts Warranty, ATC, & C-AxisSpecifications: -- Working area X-Axis 4,200mm (165.35";), Y-Axis 2,220 mm (86.61";), & Z-Axis 100 mm (3.94";). -- Min. panel size 300 x 300 mm (11.81"; x 11.81";). -- Positioning speed: X-Axis 45 MPM (147 FPM), Y-Axis 30 MPM (98 FPM), & Z-Axis 15 MPM (49 FPM).Equipped with: -- Inclined Bakelite working table, with 20° Angle with respect to vertical, (12) Independently controlled vacuum zones with Solenoid valves with EtherCAT module & Digital vacuum pressure switch, and (10) Horizontal, (1) Left vertical & (1) Right vertical retractable pneumatic stops. -- Rack & pinion drive system on X & Y-Axes, with Automatic guide lubrication. -- Brushless motors, with EtherCAT Bus drives on All axes. -- Air pressure regulator, with digital pressure gauge. Machining: -- HSD 8 kW (10-3/4 HP) - 24,000 RPM ISO30 Air-cooled electro-spindle, with ER32 20 mm (0.79";) Chuck, High frequency inverter, & Variable spindle speeds to 24,000 RPM. -- CNC-Controlled C-Axis with 360° Rotation. -- Pneumatically actuated suction hood. -- 12-Position Automatic tool changer, with Automatic preset zero tool length probe.Control: -- OSAI “OPEN SMART CNC Control, with 21-1/2"; Display, EtherCAT Bus, USB & Ethernet ports, & MICROSOFT “WINDOWS 10"; Operating system. -- Remote pendant control.Complete with: -- Electrical Cabinet Cooling System. -- BECKER 6.6 kW (8.85 HP) 250 m³/h Vacuum Pump, with inverter for vacuum pressure adjustment from control. -- (6) ISO 30 Tool holders & (6) ER32 Clamps. -- 90° Grooving Cutter & HSD Shank for C-Axis Aggregate. -- 80 mm (3.15";) Cutter for shaving spoil board.Options available at additional cost: -- 150 mm (5.91";) Dia. Circular Tools for C-Axis Aggregate. -- 135° V-Grooving Cutter. -- Z48 Saw Blade.

CASADEI (PUTSCH-Branded) EBP-950 PMCR Automatic Edgebander, New, Never Used, with Pre-Mill & Corner RoundingSpecifications: -- Edgebanding thickness: 0.4 - 3 mm (0.02" - 0.12") Coil, 0.4 - 5 mm (0.02" - 0.20") Strip with Manual feed. -- Panel thickness 8 - 45 mm (0.31" - 1.77"), Min. panel width 95 mm (3.74"), & Min. panel length 110 mm (4.33"). -- Feed speed 9 MPM (29 FPM).Equipped with: -- Pre-Mill Unit, with (2) 0.75 kW (1 HP) - 12,000 RPM - 200 Hz Motors, Counter-rotation, (2) 60 mm Dia. x 52 mm H (2.36"; Dia. x 2.05"; H) Diamond cutterheads, Max. milling adjustment 2 mm (0.08"), & Dedicated extraction system with Blower. -- Anti-Adherence Spray Unit. -- Infrared lamp. -- PURE (PUR & EVA) Hot melt gluing system, with Teflon-coated glue pot with (6) 1,315 W Heating elements with (4) in Glue pot, (1) in Turret & (1) in Glue spreading roller, Thermostatic glue control, Automatic standby & Temperature display, and Automatic glue drainage. -- Pneumatically-operated guillotine. -- Pressure section, with (1) Large driven & (2) Small idler rollers. -- Feed chain, with Scratch resistant, non-slip rubber pads. -- Top pressure beam, with (2) Rows of rubber rollers. -- Safety enclosure. -- PLC Control, with ETOUCH 7" Backlit LCD touchscreen display, 99-Program Storage, & Diagnostics.Workstations: -- Front & Rear End Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, & (2) 80 mm (3.15";) Knives. -- Top & Bottom Flush/Bevel/Radius Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motors, 75 mm (2.95") Dia. Cutters with Disposable R1/R2 3"; Knives, 2 - 3 mm (0.08" - 0.012") Radii, & 15° Bevel. -- Corner Rounding Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, 50 mm (1.97";) Diamond cutterheads, 50 mm (1.97";) Vertical/Horizontal copiers for profiling straight, curved, & beveled edges, & PLC-selectable front, rear, or complete panel processing. -- Edge Scraping Unit, with 2 mm (0.08";) Cutters, -- Top & Bottom Glue Scraping Unit, with 120 mm (4.72";) Vertical disc copier. -- Top & Bottom Buffing Unit, with (2) 0.13 kW (0.17 HP) - 1,400 RPM Motors. -- Polishing Spray Unit, PLC-Controlled, with (2) Sprayers. -- Antistatic & Cooling Spray UnitNOTE: Sold "As Is" Without Warranty!

CASADEI (PUTSCH-Branded) EBP-950 PMCR Automatic Edgebander, New, Never Used, with Pre-Mill & Corner RoundingSpecifications: -- Edgebanding thickness: 0.4 - 3 mm (0.02" - 0.12") Coil, 0.4 - 5 mm (0.02" - 0.20") Strip with Manual feed. -- Panel thickness 8 - 45 mm (0.31" - 1.77"), Min. panel width 95 mm (3.74"), & Min. panel length 110 mm (4.33"). -- Feed speed 9 MPM (29 FPM).Equipped with: -- Pre-Mill Unit, with (2) 0.75 kW (1 HP) - 12,000 RPM - 200 Hz Motors, Counter-rotation, (2) 60 mm Dia. x 52 mm H (2.36"; Dia. x 2.05"; H) Diamond cutterheads, Max. milling adjustment 2 mm (0.08"), & Dedicated extraction system with Blower. -- Teflon-coated glue pot with (6) 1,315 W Heating elements with (4) in Glue pot, (1) in Turret & (1) in Glue spreading roller, Thermostatic glue control, and Automatic standby & Temperature display. -- Pneumatically-operated guillotine. -- Pressure section, with (1) Large driven & (2) Small idler rollers. -- Feed chain, with Scratch resistant, non-slip rubber pads. -- Top pressure beam, with (2) Rows of rubber rollers. -- Safety enclosure. -- PLC Control, with ETOUCH 7" Backlit LCD touchscreen display, 99-Program Storage, & Diagnostics.Workstations: -- Front & Rear End Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, & (2) 80 mm (3.15";) Knives. -- Top & Bottom Flush/Bevel/Radius Trim Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motors, 75 mm (2.95") Dia. Cutters with Disposable R1/R2 Knives, Vertical nesting copiers, 2 - 3 mm (0.08" - 0.012") Radii, & 15° Bevel. -- Corner Rounding Unit, with 0.22 kW (1/3 HP) - 12,000 RPM - 200 Hz Motor, 50 mm (1.97";) Diamond cutterheads, 50 mm (1.97";) Vertical/Horizontal copiers for profiling straight, curved, & beveled edges, & PLC-selectable front, rear, or complete panel processing. -- Edge Scraping Unit, with 2 mm (0.08";) Cutters.NOTE: Sold "As Is" Without Warranty!