MEADOWS MILLS 2-STRAND SAWMILL STOP-N-LOAD LOG DECK -- Deck strands constructed with 4" x 8" x 1/4" wall tubing -- Chains run in 4" channel lined with UHMW wear strips -- Hydraulic Cylinder: One 2" x 12" with 1 1/2" rod -- Chain is WR-78 -- Front and rear crossbars are constructed with 6" wide flange beam -- Sawmill style stop-n-load -- Hydraulic drive with Auburn (or equivalent gear box from alternate manufacturer) gear box -- Strand spacing is determined by buyer, standard is 6 feet -- Controls: not included in base price -- Legs may be included for an additional cost -- Log decks are disassembled and bundled for shipment

MEADOWS MILLS 3 STRAND SAWMILL STOP-N-LOAD LOG DECK -- Deck strands constructed with 4" x 8" x 1/4" wall tubing -- Chains run in 4" channel lined with UHMW wear strips -- Hydraulic Cylinder: One 2" x 12" with 1 1/2" rod -- Chain is WR-78 -- Front and rear crossbars are constructed with 6" wide flange beam -- Sawmill style stop-n-load -- Hydraulic drive with Auburn (or equivalent gear box from alternate manufacturer) gear box -- Strand spacing is determined by buyer, standard is 6 feet -- Controls: not included in base price -- Legs may be included for an additional cost -- Log decks are disassembled and bundled for shipment

MEADOWS MILLS 4 STRAND SAWMILL STOP-N-LOAD LOG DECK -- Deck strands constructed with 4" x 8" x 1/4" wall tubing -- Chains run in 4" channel lined with UHMW wear strips -- Hydraulic Cylinder: One 2" x 12" with 1 1/2" rod -- Chain is WR-78 -- Front and rear crossbars are constructed with 6" wide flange beam -- Sawmill style stop-n-load -- Hydraulic drive with Auburn (or equivalent gear box from alternate manufacturer) gear box -- Strand spacing is determined by buyer, standard is 6 feet -- Controls: not included in base price -- Legs may be included for an additional cost -- Log decks are disassembled and bundled for shipment

MEADOWS MILLS 2 STRAND DEBARKER STOP-N-LOAD LOG DECK -- Deck strands constructed with 4" x 8" x 1/4" wall tubing -- Chains run in 4" channel lined with UHMW wear strips -- Hydraulic Cylinder: One 2" x 12" with 1 1/2" rod -- Chain is WR-78 -- Front and rear crossbars are constructed with 6" wide flange beam -- Debarker style stop-n-load -- Hydraulic drive with Auburn (or equivalent gear box from alternate manufacturer) gear box -- Strand spacing is determined by buyer, standard is 6 feet -- Controls: not included in base price -- Legs may be included for an additional cost -- Log decks are disassembled and bundled for shipment

MEADOWS MILLS 3 STRAND DEBARKER STOP-N-LOAD LOG DECK -- Deck strands constructed with 4" x 8" x 1/4" wall tubing -- Chains run in 4" channel lined with UHMW wear strips -- Hydraulic Cylinder: One 2" x 12" with 1 1/2" rod -- Chain is WR-78 -- Front and rear crossbars are constructed with 6" wide flange beam -- Debarker style stop-n-load -- Hydraulic drive with Auburn (or equivalent gear box from alternate manufacturer) gear box -- Strand spacing is determined by buyer, standard is 6 feet -- Controls: not included in base price -- Legs may be included for an additional cost -- Log decks are disassembled and bundled for shipment

Complete MEREEN-JOHNSON/CHOICE MACHINERY GROUP 431-DC-1/C1210 - C1260 31" Gang Rip Saw LineConsisting of the following machines as late as 2022: -- 2022 CHOICE MACHINERY GROUP C1210 5-Chain Transfer Deck Conveyor, S/N 1048, with 1/2 HP - 1,720 RPM TEFC Motor. -- 2022 CHOICE MACHINERY GROUP C1220 Automatic Unstacker/Panel Feeder, S/N 1049, with Unstacker platform with (4) Motorized rollers, Safety light curtain, & 5 HP Hydraulic unit, and Automatic panel feeder with Chain-driven pusher & 3/4 HP - 1,710 RPM TEFC Motor. -- MEREEN-JOHNSON 431-DC-1 Dip Chain Gang Rip Saw, S/N MJ-6837 (Approximately 2003), with 7,564 Hrs., Arbor cap. 31", Max. blade dia. 14", Max. thickness 3-1/2", Min. length: 29" for Glue joint accuracy & 22" for Busting, Throat 6", Variable feed speeds 30 - 170 FPM, with 75 HP - 3,600 RPM TEFC Direct drive arbor motor with Disc brake, Load meter & Arbor lockout for access door; "POSI-FEED" Dip bed with 5" Pitch Hardened double-V chain, "QUAD LIFE" Hardened dip cams, 2-3/8" x 14"; Extruded structural aluminum feed bed slats with 1-3/4"; Replaceable steel-backed rubber insert strips, Automatic chain lubrication with Low-level shutoff, & 5 HP Feed motor with Adjustable jam protection; (4) 3" Dia. Air-loaded overhead pressure rolls, Full width spring-loaded overhead bed plate, Motorized thickness adjustment, Anti-kickback finger system with (1) Lower & (2) Upper on infeed & (1) Upper on outfeed, Complete with Spare arbor with (11) Blades. -- 2022 CHOICE MACHINERY GROUP C1230 Motorized Belt Conveyor, S/N 1050, with 3/4 HP - 1,710 RPM TEFC Motor. -- 2022 CHOICE MACHINERY GROUP C1240 Dual Reel Automatic Strapper/Stacker, S/N 1051, with SOUTHWORTH 4,000 Lb. Cap. Electric/hydraulic scissor lift platform with 3.3 HP Hydraulic unit, & Safety light curtain. -- 2022 CHOICE MACHINERY GROUP C1250 Tilt Unit, S/N 1052, with 5 HP Hydraulic unit & Motorized rollers with 1/2 HP - 1,720 RPM TEFC Motor. -- 2022 CHOICE MACHINERY GROUP C1260 Motorized Roller Conveyor, S/N 1053, with End Stop. -- 2022 CHOICE MACHINERY GROUP C12XX Control Console, with S/N 1054, with SCHNEIDER "MAGELIS" Touchscreen control & Steel bar grating operator platform.NOTE: Please check back for additional specifications and video.

MEREEN-JOHNSON "312-DC-OPH1" DIP CHAIN GANG RIP SAWSpecifications -- 12" Arbor cap., -- 14" max. dia. tooling, 3-1/2" max. thickness, -- 30" min. length for glue joint accuracy & 22" min. for busting only; -- 6" throat. Equipped with: & Features -- 50 HP - 3,600 RPM TEFC Direct drive motor, -- Arbor with disc brake & load meter, arbor lockout on access door.Feed & chain: -- 3 HP Variable feed speed from 30 - 150 FPM with adjustable jam protection, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain, "Quad Life" hardened dip cams. -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips, -- Automatic chain oiler with low level shutoff. -- (4) 3" Dia. air loaded overhead pressure rolls; -- Full width segmented maple, spring loaded overhead pressure shoe -- Pressure rolls & pressure shoe unit adjust with scale & pointer thickness reference -- Anti-kickback fingers. -- Lasers at infeed for pocket location.

MEREEN JOHNSON 424 DC Multiple Blade Rip Saw:Specifications -- 24" Arbor cap., -- 14" max. dia. tooling, -- 3-1/2" max., -- 22" min. length, -- 6" throat -- 75 HP - 3,600 RPM TEFC Direct drive motor, arbor with disc brake. -- Feed & chain: 3 HP Variable feed speed from 50 to 150 FPM, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain, -- "Quad Life" hardened dip camsEquipped with & Features -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips -- Automatic chain oiler with low level shutoff. -- (4) 3" Dia. air loaded overhead pressure rolls; -- Full width spring loaded overhead bed plate -- Height adjustment with scale & pointer reference --Anti-kickback finger system with (1) lower & (2) upper on infeed -- (2) Upper dust hoods, (1) 10" & (1) 5" dia. & (1) lower 4" dia. hood, requires 3,820 CFM

MEREEN JOHNSON 424 DC Multiple Blade Rip Saw:Specifications: -- 24" Arbor cap., 14" max. dia. tooling, 3-1/2" max., 22" min. length, 6" throat. -- 75 HP - 3,600 RPM TEFC Direct drive motor, arbor with disc brake. --Feed & chain:3 HP Variable feed speed from 50 to 150 FPM, M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain, -- "Quad Life" hardened dip cams, extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips, automatic chain oiler with low-level shutoff. --Equipped with & Features: -- (4) 3" Dia. air-loaded overhead pressure rolls -- Full width spring-loaded overhead bed plate -- Height adjustment with scale & pointer reference -- Anti-kickback finger system with (1) lower & (2) upper on infeed. -- (2) Upper dust hoods, (1) 10" & (1) 5" dia. & (1) lower 4" dia. hood -- Requires 3,820 CFM

MEREEN-JOHNSON Model "424-DC/SR ( 1 ) Moving Blade Gang Rip SawSpecifications -- 24" Arbor cap., -- 14" max. dia. tooling, -- 3-1/2" max., -- 22" min. length, 6" throat. -- "Select-A-Rip" multiple Rip Saw with rapid adjustment of (1) moveable saw blade (shifts at approx. 3" per second); can be used independently or in conjunction with a gang sleeve arrangement; provides straight line gang ripping while maintaining optimum yield and delivering glue-joint accuracy.Equipped with & Features -- Select-A-Rip includes a control console and overhead laser lights for accurate blade positioning. -- 75 HP - 3,600 RPM TEFC Direct drive motor. -- Feed & chain: 3 HP Variable feed speed from 50 - 150 FPM, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain, "Quad Life" hardened dip cams, -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips, -- Automatic chain oiler with low level shutoff. --: (4) 3" Dia. air loaded overhead pressure rolls; full width spring loaded overhead bed plate, -- Eight ( 8 ) adjustment with scale & pointer reference; -- Anti-kickback finger system with (1) lower & (2) upper on infeed. -- (2) Upper dust hoods, (1) 10" & (1) 5" dia., requires 3,820 CFM. -Note From The Seller Machine was used in a low production environment and has low hours.

MEREEN-JOHNSON 419-DC Gang Rip Saw --Specifications -- 19" Arbor cap., -- 14" max. dia. tooling, -- 3-1/2" max. manual thickness adjustment, -- 29" min. length for glue joint accuracy and 22" min. for busting only, 6" throat. --Equipped with & Features -- 75 HP - 3,600 RPM drive motor with direct drive to arbor. -- Feed & chain: 3 HP Variable feed speed 30 to 150 FPM, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain, hardened dip cams, extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips, and chain oiler. -- (4) 3" Dia. spring loaded overhead pressure rolls (with new springs); full width spring loaded overhead bed plate, pressure rolls and bed plate unit with scale & pointer thickness reference; anti-kickback finger system , -- (1) lower & (2) upper on infeed (kickback fingers are newly replaced). -- (2) Upper dust hoods (1) 10" & (1) 5" dia., and (1) lower 4" dia. hood; requires 3,820 CFM; (2) 19" saw sleeve with mics. spacers. -- New Laser Light Array complete with (5) Lasers and Mounting Hardware, --. Spare parts including extra saw sleeve, short stock holddown plates, a few sawblades, etc. -- Notice the feed chain - it's in exceptional condition! --Note From The Seller Arbor motor burnt out, needs repair

Mereen-Johnson 424 DCS Short Stock Gang Rip sawSpecifications -- 24" Arbor cap., -- 14" max. dia. tooling, -- 3-1/2" max. manual thickness adjustment, -- 14" min. length for glue joint accuracy and 22" min. for busting only, -- 6" throat. Equipped with and Features -- 75 HP - 3,600 RPM TEFC Direct drive motor, -- 2-3/16" dia. arbor with disc brake, -- load meter and slip-off outboard bearing. -- Feed & chain: 3 HP Variable feed speed 30 to 170 FPM, -- M-J "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain -- "Quad Life" hardened dip cams -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips --, Automatic chain oiler. -- (4) 3" Dia. air loaded overhead pressure rolls; full width spring loaded overhead bed plate, -- Pressure rolls and bed plate unit with scale & pointer thickness reference; -- Anti-kickback finger system with (1) lower & (2) upper on infeed. -- Sound enclosure, -- (2) Upper dust hoods (1) 10" & (1) 5" dia. and (1) lower 4" dia. hood, -- Requires 3,820 CFM;NOTE: Laser Rack with 10 Lasers

MEREEN-JOHNSON - 431DC, ...Gang Rip Saw: Specifications: -- 31" Arbor width cap., 14" max. dia. tooling, 3-1/2" max thickness. -- Motorized thickness adjustment. -- 29" Min. length for glue joint accuracy and 22" min. for busting only; 6" throat. -- 75 HP - 3,600 RPM TEFC direct drive motor. -- Arbor with disc brake & load meter. -- Arbor lockout on the access door.Equipped with & Features: -- Feed, Chain & Holddown. -- 5 HP Variable feed speed 30 - 150 FPM with adjustable jam protection. -- MEREEN-JOHNSON "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain. --"Quad Life" hardened dip cams. -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips. -- Automatic chain oiler with low-level shutoff. -- (4) 3" Dia. air loaded overhead pressure rolls. -- Full width spring loaded overhead bed plate. -- Pressure rolls & bed plate unit with powered adjustment; scale & pointer for thickness reference; -- Antikickback Finger System with: (1) Lower & (2) Upper on Infeed; (1) upper assembly on outfeed.

MEREEN-JOHNSON - 431DC, ...Gang Rip Saw: Specifications: -- 31" Arbor width cap., 14" max. dia. tooling, 3-1/2" max thickness. -- Motorized thickness adjustment. -- 29" Min. length for glue joint accuracy and 22" min. for busting only; 6" throat. -- 75 HP - 3,600 RPM TEFC direct drive motor. -- Arbor with disc brake & load meter. -- Arbor lockout on the access door.Equipped with & Features: -- Feed, Chain & Holddown. -- 5 HP Variable feed speed 30 - 150 FPM with adjustable jam protection. -- MEREEN-JOHNSON "Posi-Feed" dip bed carried on 5" pitch hardened double-V chain. --"Quad Life" hardened dip cams. -- Extruded structural aluminum feed bed slats with replaceable steel backed rubber insert strips. -- Automatic chain oiler with low-level shutoff. -- (4) 3" Dia. air loaded overhead pressure rolls. -- Full width spring loaded overhead bed plate. -- Pressure rolls & bed plate unit with powered adjustment; scale & pointer for thickness reference; -- Antikickback Finger System with: (1) Lower & (2) Upper on Infeed; (1) upper assembly on outfeed.

MEREEN-JOHNSON Model 524-DDCSR 2+4 Double Arbor Gang Rip SawSPECIFICATIONS: -- First Arbor Arranged with Two (2) Independently Adjustable Select Saw Assemblies for Mounting Hogging Blades -- Second Arbor with Four (4) Independently Adjustable Select Saw Assemblies -- Arbor Space 24" -- Thickness Capacity to 1-3/4" with 12" Tooling and 2-3/4" Using 14" Tooling -- Minimum Length 30"Equipped with & Features -- Two (2) M-J Direct Drive Motors 75 HP Each -- Feed Motor 7.5 HP TEFC, 30' to 235' rate with Frequency Inverter Speed Control -- Saw Set Up for Second Party Optimizing System.

ORIGINAL 3512-03 RADIAL ARM SAW (Contractor Series)The Contractor Duty Series is an industrial rated machine that has the versatility to crosscut, bevel cut, miter cut, and swivel to a rip position to cut down panels precisely and accurately. These machines are well suited for cutting off up to 3"; material, as well as cutting off 24"; wide panels for squaring shelving and doors and other similar applications. -- Specifications: -- 3 HP TEFC Saw motor; 12" dia. blade; 1" x 2-3/16" saw arbor; 3-1/16" thickness cap. @ 90°, 1-1/4" @ 45°; 24-1/4" crosscut cap. with 1" stock; 21-1/4" with 3" stock; 16" max. miter cut @ 45° with 1" stock; 34-15/16" rip cap. -- Features: -- Swivel arm for miter cuts, swivel motor for bevel cuts; indexing yoke to 90° for rip cutting panels; saw head with automatic motor brake and automatic spring return; positive locking device for tilting; upper and lower blade guards with anti-kickback attachment. -- Complete with: -- 34" x 26" MDF table; sturdy powder coated cast iron frame; heavy gauge steel base and support legs. -- Optional: --12" x 36 or 60-Tooth x 1" Bore saw blade; OS Series manually adjustable measuring systems; OS Series material handling roller and flat tables; dust collection hoods; key access limiting switch and emergency stop switch.

ORIGINAL 3546 RADIAL ARM SAW (Heavy Duty Series)The Heavy Duty Series is a very precise machine made for the rigors of every day industrial use. Straight, miter, bevel and compound bevel cutting in a heavy gauge steel powder coated frame & legs. Specifications: 5 HP TEFC Saw motor; 16" dia. blade; 1" x 2-3/16" saw arbor; 4-15/16" thickness cap. @ 90°, 2" @ 45°; 24" crosscut cap.; 15-1/2" max. miter cut @ 45°; 37-7/8" rip capacity. Features: -- Swivel arm for miter cuts, swivel motor for bevel cuts; indexing yoke to 90° for rip cutting panels; saw head with automatic motor brake and automatic spring return; positive locking device for tilting; upper and lower blade guards with anti-kickback attachment. Complete with: -- 42-1/2" x 31-1/4" MDF table; sturdy powder coated cast iron frame; heavy gauge steel base and support legs. Optional: -- 16" x 60-Tooth x 1" Bore saw blade; pneumatic clamping systems; power carriage feed; 14" & 22" wide roller tables.

ORIGINAL 3558 RADIAL ARM SAW (Super Duty Series)The Super Duty Series is the ultimate workhorse of the industry, capable of operating 2 to 3 shifts per day. Miter & bevel cutting, compound miters and dado operations. Constructed of heavy-duty cast and ductile iron for vibration-free operation. Specifications: -- 7.5 HP TEFC Saw motor; 20" dia. blade; 1" x 3-1/8" saw arbor; 6-1/4" thickness cap. @ 90°, 3-1/4" @ 45°; 32" crosscut cap.; 21-5/8" max. miter cut @ 45°; 48-3/4" rip cap. Features: -- Swivel arm for miter cuts, swivel motor for bevel cuts; indexing yoke to 90° for rip cutting panels; saw head with automatic motor brake and automatic spring return; positive locking device for tilting; upper and lower blade guards with anti-kickback attachment. Complete with: 58" x 50" MDF table; sturdy powder coated cast iron frame; heavy gauge steel base and support legs. Optional: -- 20" x 60-Tooth x 1" Bore saw blade; pneumatic clamping systems; power carriage feed; 14" & 22" wide roller tables.

ORIGINAL 3691-03 Overhead Rail Panel SawSpecifications: -- Sturdy welded steel frame for saw head and beam arm; 7.5 HP motor; 1" dia. arbor; 1-3/8" long arbor; saw head with automatic electro-mechanical motor brake. -- 20" Max. blade dia.; 7" max. cutting depth @ 90°; 3-1/2" @ 45°; 62" long x 1", 4" & 6" thick max. crosscut cap. -- Complete with: -- 36" x 60" MDF table; heavy gauge steel base & legs for solid support. -- Includes: -- Upper & lower blade guards; magnetic starter and overload protection. -- Single-phase option available for;...$ 250.

ORIGINAL 3691-01-7 Overhead Rail Panel SawSpecifications: -- Sturdy welded steel frame for saw head and beam arm; 7.5 HP motor; 1" dia. arbor; 1-3/8" long arbor; saw head with automatic electro-mechanical motor brake. -- 20-1/2" Max. blade dia.; 8" max. cutting depth @ 90°; 4" @ 45°; 60" long x 1" max. crosscut cap. -- Complete with: -- 36" x 60" MDF table; heavy gauge steel base & legs for solid support. -- Includes: -- Upper & lower blade guards; magnetic starter and overload protection.