Mereen Johnson Model 312 DC SR1R Rip Saw 600 V/3 PH/60 Cy

- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”

Northteck MRS-14-DXL 460v Manufacturer notes: This is a very popular machine and cost effective. New open ended design allows for you to cut wide material up to 27-1/8? wide. Plus spare arbors, lasers, and the optional quick locking, easy to adjust infeed will not break the bank. The Northtech heavy-duty 50 HP multi-rip (“gang-rip”) saw with 15? maximum blade diameter quickly and accurately cuts material up to 4-15/16? thick and 27-1/8” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Laser guides (one included) and an optional 103” fence make proper alignment of even the longest material simple and precise. Variable feed speeds of 25 – 120 FPM and powered height adjustment further improve operator efficiency.

Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

This machine was reported to be in running condition when removed from service. Looks like a Pendu. Cannot find a plate on the machine to confirm. this is a single arbor gang and it does not have a sizer. 75 HP Main Motor 5 HP Drive motor

Raimann KM310 Rip Saw Per seller: The saw runs material. The variable infeed is stuck on one speed.

Raimann UniRip 310 Rip Saw Misc spacers and blades Bought new in 2020

Raimann KM310M Rip Saw ValuRip Infeed System One moving Blade

Raimann Unirip 310 Gang Rip

Raimann KM310M Rip Saw 2 Moveable Blades

Salem Top Arbor Gang Rip Saw 8" Capacity 300 HP Motor Blades: Approx 30 Sharpened carbide blades still have wax, and 30 that need to be sharpened Includes: All electrical, misc blades, guides, spacers Included: Milling machine and Babbitt pot System needs a 10 HP feed motor

SCMI M3 Gang Rip Saw Includes: Misc blades

SCMI M3 Rip Saw Still under power for inspection

Shurman Double Arbor Gang Saw 12" Capacity Thin Kerf Babbit Grinder

It is a 2 saw re-rip with one moveable saw and an adjustable fence. Capacities: Minimum length = 8” Maximum length = 192” Minimum width = 1 ½” Maximum width = 6” Minimum thickness = 7/8” Maximum thickness = 1”

Multirip circular saw for block cutting, with reinforced structure and high production speed. Trailed top and bottom rollers, upper rollers with adjustment, shafts with cartridge system for quicker and more efficient replacement of the set of saws, U-beam base with levelers and central lubrication. It does not come with the circular saws. - Maximum inlet width: 600 mm; - Minimum inlet height: 70 mm; - Maximum inlet height: 160 mm; - Double arbor: Ø 80 mm; - Number of saws per axle: 10x; - Exterior saws Ø: 350 mm interior saws - Ø: 110 mm; - Upper press rollers: 2x; - Bottom rollers: 6x; - Max. Feed speed: 35 m L / min for logs - 160mm above in diameter; - Max. Feed speed: 40-50 m L / min - only for logs 130-160mm in diameter; - Lower main motor indicated: 200 hp 2p (1x) Included; - Top main motor indicated: 150 hp - Main motor belt: 4 / 3v (8 Pcs); - Motor traction of the rollers: 5 cv 4p; - Gearmotor: GS (crown and pinion); - Length: 3366 mm; - Width: 2782 mm; - Height: 2233 mm; - Approximate weight: 5.470 kg

Wintersteiger DSG Sonic Frame Saw

Barr Mullin Wondersaw Optimizer with Computerized Laser Controls Tichniess: Up to 3" Width: 31" Min cut: 4" Feed height: 34-1/2" Floor Space: Apprx 21' x 15' 480 volt

10 HP 3200 rpm main motor 2.7 HP feed motor Cuts on crayon marking Variable feed up to 262 fpm 18” blade 30 mm arbor 460 volt 3-phase (2) Roller conveyors can be included if needed