Irvington Moore Lumber Stacker Can make packs 4'-8' Was running approximately 4-5 years ago

175 KW -175 KVA 264 amps at 460v John Deere diesel powered 460v - 208v - 115v outlets housed in a container with ample access doors

Joy Model 290 Rotary Screw Compressor Compressor 275 cfm@110psi 10 gallon oil sump capacity Complete with with dryer and holding tank as pictured. 460 volt

Joy 20 HP Compressor Approx 10,000 hours Just had oil change, new separator element, oil filters, drive belts

This unit needs a new seal that costs about $75.

Pallet racking 9'6 ft & 8’4 racks X 42” wide and 16’ tall 31 - 4 shelf racks or can expand to 62 shelf racks (2 shelves)

(9) Pallets available Each pallet has 48 cases.

Scragg and Slab Edger 7 blade 42" – 56" wide Needs rebuilt No motors

40 hp Sawdust Blower

This unit was blowing dust to a large baghouse in a large facility. There is also a 75 HP blower and baghouse available at the same location. Piping is available. Unit will be loaded on the truck.

10 HP Dust Fan with ductwork 230/460 volt 3-phase

????34' kiln with 5,500 BF of 4/4 lumber capacity Hot water system wood/oil boiler combo Wet bulb/dry bulb with 7 fans that change directions for air flow on adjustable timers 2 16'x5' karts Unit comes with 2 axles, tires, skirting for bottom enclosure, panel box with switches and timers

2 saw cutoff 12” blades 20 HP motor, 4 chain, C55 rooftop 2 HP heavy gearbox on feedworks Ready to load

75 HP 550 Volt 3 phase

15 HP 460 volt 3-phase 63 CFM Capacity

USNR 60,000 Board Foot Kilns (10) Available

Valley 2 Blade Edger 1 Fixed, 1 Moveable Blade 24" Wide, Will Cut Up To 3" Thick 20hp 480V New Mandrel and Mandrel Bearings New Outfeed Rollers

The Vantec Wood Wast Drum Chipper is used to produce chips from logs and veneer waste. It has a roller infeed system, rubber conveyor belt and hydro-pneumatic unit to lift the rotor for maintenance. Manufacturer specs: - Width of inlet: 600 mm; - Height: 200 mm; - Rotor diameter: 600 mm; - Toothed roller: 01 upper and 02 - lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical - gears); - Upper Rollers motor size: 5 hp; - Upper Rollers motor size: 5 hp; - Feed speed: 40m/min; - Number of rotor knives: 02; - Wood chip size: 30 - 40 mm; - Chipper screen: size: 65 x 65mm - Main motor 100 hp 4P: Included; Drive panel: Included; - Estimated production: 38 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 650 mm; - Height: 1 .000 mm; - Overall length: 5800 mm; Approximate weight: 2,900 kg.

This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

This Wood Drum chipper PT750 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, rubberized conveyor belt and Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. Width of inlet: 750 mm; • Height: 300 mm; • Rotor diameter: 800 mm; • Toothed roller: 03 upper and 03 lower; • Grooved rollers: 01; • Rollers gear motor: GD (helical gears); • Upper Rollers motor size: 7,5 hp (2x); • Feed speed: 35 m/min; • Number of rotor knives: 02; • Wood chip size: 25 - 40 mm; • Chipper screen: size: 70x 70mm; • Main motor 200 hp 4P: Included; • Drive panel: Included; • Estimated production: 65 m3 / h (it may vary according to the type of material and time used with blade sharpening); • Lead Time: 240 Days • Infeed conveyor length: 3 500 mm (included); • Width: 2 500 mm; • Height: 1.250 mm; • Overall length: 7 300 mm; • Approximate weight: 8 750 kg.