- Close link chain vs. open (no dust or pinch point) - Oiler has twice the number of lube points (critical) - The VS adjustment location on the 14N. - Can cut up to 4 15/16? with 14? blade vs. the MRS-12 12? blade 3-15/16”. - Can run 12? as well on the MRS-14N - Bottom kickback fingers for added safety - Saws, with proper tooling and material, can glue line Specifications: - Main Motor Hp. = 50 Hp. - Voltage/ Freq. = 460 Volt 60Hz - Phase = 3 Phase - Amp Requirement = 35 Amps - Feed Hp. = 2 Speed 1.5 / 3 Hp. - Feed System = Feed Chain - Feed Speed = 25 – 120 FPM - Variable Speed = Variable Speed Pulley - Elevation Hp. = 1/4 Hp. - Elevation Style = Manual Wheel Adjustment - Elevation Sys. = Jack Screw / Linear Guides - Total Hp. = 53.25 Hp. - Electronics = CE Approved Components - Dual Voltage = Elevation Arbor Motors - Control Voltage = 110 Volt - Assisted Start = Wye-Delta - Pass-Line = 33-1/2” - Min. Length = 17-3/4” - Min. Width = 1/2” - Max. Width = 27-1/8” - Min. Thickness = 5/16” - Max. Thickness = 4-15/16” - Arbor Rpm = 3570 Rpm - Blade Size = 12” Tungsten Carbide Tipped - No. of Teeth = 36 Tooth - Blade Kerf = 3.5 mm - Cleaning System = Brush on Chain - Vertical Travel = 3/8” – 5” - Dust Collection = (2) 6” @ 1962 CFM - Arbor Diameter = 70 mm - Hold Down Style = Pressure Plate - Kickback Finger = (2) Top (1) Bottom Sets - Emergency Stop = Push Button - Rear E Stop = Push Button - Safety Feature = Safety Interlock Switch - Guarding = Full Cabinet Enclosure - Oiler = Automatic Mechanical Oiler - Low Oil Warning = Low Oil Shut-off - Fence Type = Adjustable - Fence Dims. = 103” Length - Frame Const. = 5/16” Steel Construction - Worktable Dims. = 27-1/8” x 64” - Infeed Table = 13-3/4” x 103” - Decible Rating = 74 dB - Net Weight = 4402 Lbs. - Gross Weight = 4694 Lbs. - Machine Dims. = 67” x 58” x 71” - Packaging Dims = 72” x 65” x 77”

Has (2) Blades Will cut up to a 12 x 12" Powered by (2) 20 HP 460 Volt 3 Phase motors Runs (2) 1 1/4" band blades Excellent Condition, (new condition with less than 4 hours use).

Nyle PHT350 Kiln System was powered up and tested, but not put into production.

Nyle Firewood Dry kiln No chamber included

Optimal 4-Side Canter See photos fro complete specs

This machine was purchased as "rebuilt" by the manufacturer and never put into service at the current location. Ready to load.

Pallet Repair System Disc Dismantler Pallet size: 3.875" Stringer Width Max. (.098 m) 1.25" Deckboard Thickness Max. (.031 m)

Pallet Band Dismantler

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

Peerless Chip Bin MOD 14

This machine was reported to be in running condition when removed from service. Looks like a Pendu. Cannot find a plate on the machine to confirm. this is a single arbor gang and it does not have a sizer. 75 HP Main Motor 5 HP Drive motor

Pendu Stacker No hydraulic pack

Good Condition Infeed Hydraulic Power Unit Stacker

Pneumafil Dust Collector Model 135 (13.5-460-8): 150 hp. The round duct enters the collector at 48" Diameter. Dixie Air Dust Collector: Size: 108-12, Type: SPB, 50 HP, Inlet to the motor, circumference is 90".

This is crated, ready to go! The price includes the machine only, options are available upon request. 12 month warranty The semi-automatic pallet nailing machine is an ideal tool to produce various types and sizes of pallets on blocks and stringers. Its construction allows for fast and easy changeovers. Only one operator is needed, and it reaches an output of 210-230 pallets per 8-hour shift (depending on the operator skills and work organization). - Two nail guns with different size nails are suspended on two spring balancers for better tool handling. (Nail guns are an optional add-on) - Pneumatic block/stringer holders and pallet lifters ensures high quality and easy handling. Benefits: • Easy to use: one operator can build 210 - 230 pallets within 8 hours • Compact design: total footprint 3.3 m2 (35.5 ft2) • Universal: adjustable worktop allows production of stringer pallets on 2, 3, 4, or 5 stringers and block pallets (including EUR pallets) up to 9 blocks • Efficient: quickly switch to any size pallet • Pneumatic clamp: easily centers stringers or blocks • Pneumatic lift: raises pallet to minimize operator lifting • Overhead roller track: nail guns can move freely during work • Bottom template: template to build pallet legs • Adjustable steel clinch plates: galvanized and hardened steel plates for clinching nails • Unique: diagonal table adjustment reduces work by 50%; option to assemble CP1, CP2, CP3, CP4, CP5 pallets; only 2 Allen keys required to adjust the table Technical Specifications: • Weight: 970 lb (440 kg) • Operating pressure: up to 8 bar (116psi) • Material: structural steel Pallet Dimensions: • Width: 31.5" - 74.8" (800 - 1900 mm) • Lenght: up to 51.2" (1300 mm) External dimensions: • Worktop width: 88.6" (2250 mm) • Table width comprising rail mounting system for balancers: 122.9" (3122 mm) • Worktop height: 64.1" (1627 mm) • Total height including rail mounting system for balancers: 101.6" (2581 mm)

Pneumatico Block Nailer Hardly used - ready to ship!

Powermatic model 66 Table Saw

This saw is no longer required at the current facility. Available for immediate removal! - Prescott Vertical Resaw - 10" Silver Tooth blades; 37'7" Long - 72" Bandwheels - 250 HP Motor - no starter

The Stringer-Mate Model SS200 offers high production splicing for operations with higher volume requirements. A two stage pump produces a 4 second cycle time for a productive, efficient splicing operation. The hydraulic system requires only 110 volt, single phase electricity to operate.

PRS Dual Max Trim Saw with Conveyors