This system was running daily before hte facility shut down 4-years ago. Buyer will need to provide rigging. (240) 4" x 12' Bags 100 HP Main Motor Bags are cleaned by compressed air approx every minute System is approx 1998 Approx 35000-38000 CFM

Donaldson Model ECB & ECB-2 Dust Collector - 3-units total Control Panel

DOOSAN portable lighting with only .2 hours.

Edmiston 4 Head Block Circular Sawmill Running daily Won't be available until April

Complete sawmill that is used daily. Infeed deck to debarker Morbark debarker with bark conveyor Infeed deck to mill Edmiston Sawmill: 4 HB Carriage, operator cab, drop conveyor for slabs Edmiston Edger Greenchain with rooftop Precision 48" Chipper with infeed All electrical, controls and hydraulics included

Dust blower used on Resaw or Edger 550 Volt 3 Phase 1-1/2 HP 3400 RPM

English 600 HP Boiler - (2) Units available New in 2000 One is set up for wood and only run for 3-years The second is wood/oil backup and only test fired 300' Covered Waste Conveyors available to transport waste to boilers Large capacity bucket load/silo available to store wood waste Complete loading/unloading augers available All pumps, condensate tanks, piping, electrical, catwalk, exhaust, infeed bins, suit bins, augers included. Two large stacks also available

Timber Treatment Solutions now offers an advanced incising solution for square sawn timbers with EXCALIBUR PRO, allowing a superior penetration of the wood in the subsequent preservative pressure treatment. It offers the ability to incise specific sections of post, saving on preservatives while still focusing the treatment where it is needed most and helping to retain visual product aesthetics above the ground contact line. - 1” x 1” to 20” x 20” Section Capacity - No maximum length - Incision depth up to 3/4" - 2 sets of 2 incising heads, fully sequenced with each other - Self cleaning system for blades - Incises all four faces in a single pass with incising pattern sides finishing at the same point - Full- or part-post straight-through continuous incising with a simple choice of the length and place of incision anywhere on the post - Mechanical blade separation system allows rapid setting of the machine for different timber sizes - Auto self-calibration to ensure accurate incising every time and reduce operator error

Excalibur Smart Incising for Round Timbers from Timber Treatment Solutions (TTS). - 63 mm - 200 mm Diameter (1.29"-7.8") - Minimum length of 200 mm to no max (7,8" - (9) Incising Heads - Self cleaning system for blades - Allows superior preservative penetration with pressure treatment - Optional: Customized builds for larger pole requirements

Forestor 900 Resaw 4" Blades Powered Infeed

Frick Sawmill 4 Head Block Mounted on a drop deck trailer. Everything folds up for transport. Includes: Cummins motor

Fulghum 10x90 Drum Debarker Includes Infeed

Complete mill: 96" Fulghum Chipper - 8 Knife, 1500 HP Wood splitter for oversize logs 60 Unit Chip Bin (2) Radial conveyors 155' Fulghum Radial Crane with trolley Bark hog All electrical and controls

Gardner Denver Air Compressor - 25 HP - Gardner Denver Air Dryer - 250 Gallon reservoir and stand

Generac 200 HP Genset

General Motors Power Takeoff Unit Detriot Diesel #5136548

Go Fast Single Head Resaw

Go Fast Resaw 15 HP Motor Put under power to test, never put into production.

Go Fast 5-Head Resaw Unit was cut into two pieces and can be put back together with a weld in the middle. Approx layout is 31' x 8'

Griggio C250 Rip Saw 250 mm Wide belt (10")