671 Diesel Model PTA11112

Dewalt Radial Arm Saw

Diehl Model 75 Straight Line Rip Saw Chain is in good shape. Left and right chains are worn evenly. Includes: Laser Variable Speed: 4-speeds

The seller has upgraded to a new machine and no longer needs this rip saw. This machine still runs a few times a week at the shop. 15 HP Motor 2 HP Feed Motor 2" Arbor 16" Max blade capacity Chain drive

The seller has confirmed that this Dixie Air dust collection system is in great working/running condition and it is ready to load! - Size: 108-12 - Type: SPB - 50HP - Inlet to the motor - Circumference: 90"

This system was running daily before hte facility shut down 4-years ago. Buyer will need to provide rigging. (240) 4" x 12' Bags 100 HP Main Motor Bags are cleaned by compressed air approx every minute System is approx 1998 Approx 35000-38000 CFM

Donaldson Model ECB & ECB-2 Dust Collector - 3-units total Control Panel

DOOSAN portable lighting with only .2 hours.

7.5 HP 230 volt 3phase 2 sets of fabric upper bags

7.5 HP 230 volt 3phase 2 sets of fabric upper bags

Edmiston 4 Head Block Circular Sawmill Running daily Won't be available until April

Complete sawmill that is used daily. Infeed deck to debarker Morbark debarker with bark conveyor Infeed deck to mill Edmiston Sawmill: 4 HB Carriage, operator cab, drop conveyor for slabs Edmiston Edger Greenchain with rooftop Precision 48" Chipper with infeed All electrical, controls and hydraulics included

Dust blower used on Resaw or Edger 550 Volt 3 Phase 1-1/2 HP 3400 RPM

English 600 HP Boiler - (2) Units available New in 2000 One is set up for wood and only run for 3-years The second is wood/oil backup and only test fired 300' Covered Waste Conveyors available to transport waste to boilers Large capacity bucket load/silo available to store wood waste Complete loading/unloading augers available All pumps, condensate tanks, piping, electrical, catwalk, exhaust, infeed bins, suit bins, augers included. Two large stacks also available

Timber Treatment Solutions now offers an advanced incising solution for square sawn timbers with EXCALIBUR PRO, allowing a superior penetration of the wood in the subsequent preservative pressure treatment. It offers the ability to incise specific sections of post, saving on preservatives while still focusing the treatment where it is needed most and helping to retain visual product aesthetics above the ground contact line. - 1” x 1” to 20” x 20” Section Capacity - No maximum length - Incision depth up to 3/4" - 2 sets of 2 incising heads, fully sequenced with each other - Self cleaning system for blades - Incises all four faces in a single pass with incising pattern sides finishing at the same point - Full- or part-post straight-through continuous incising with a simple choice of the length and place of incision anywhere on the post - Mechanical blade separation system allows rapid setting of the machine for different timber sizes - Auto self-calibration to ensure accurate incising every time and reduce operator error

Excalibur Smart Incising for Round Timbers from Timber Treatment Solutions (TTS). - 63 mm - 200 mm Diameter (1.29"-7.8") - Minimum length of 200 mm to no max (7,8" - (9) Incising Heads - Self cleaning system for blades - Allows superior preservative penetration with pressure treatment - Optional: Customized builds for larger pole requirements

7.5 HP single phase cyclone/dust collection assorted dust pipe and fittings as pictured

Optimatic TS-06 Tooth Straightener Manufacturer specs: Every Tooth - Every Run - Every Time Introducing the TS06 automatic bandsaw tooth straightener. This latest Filing Room innovation from OPTIMATIC is designed to work in place of the backfeed on a bandsaw sharpener. The TS06 is timed from the feed of the bandsaw sharpener. Each tooth is examined as it passes through the sensor. When a tooth is not aligned properly it will bend it back to correct it. Teeth are examined on each round of the grinder, giving the tooth straightener the opportunity to examine each tooth several times as the saw is processed and make progressive improvement putting the tooth back in line. A standard 5' resaw can generally be processed in 30 minutes. The TS06 is designed to measure the body of the tooth, just below the grinding burr and just behind the swage or tip. The actual contact point is easily adjustable. It's important to measure the body of the tooth so that we do not cover up problems with swages, shapers, or tippers. - but instead provide them a square, strong tooth to work from. 1. The TS06 has two stations. The first station feeds then measures. 2. The second station bends. Specifications:Connection values:Electrical connetion:220 V 50 Hz or special voltageAir Pressure:1/4? Gas threadAir:Minimum 5 bar air consumption, 1 liter per strokeSaw blade diameter:Saw Wide:From 80 mm to 300 mm wide or special up to 420 mmSaw Long:From 6 m in the grinding machine carousel can be integratedSaw Thickness:0,7 mm to 2,7 mmDimensions:Length:1350 mmHeight:1550 mmWidth:600 mmWorking position:1000 mm can be adapted to grinding heightWeight:210 kg

Optimal 4-Side Canter See photos fro complete specs

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system