Go Fast Resaw 15 HP Motor Put under power to test, never put into production.

GoFast 2-Head Resaw 10 HP main motors Go Fast Board Deduster

Good/Fair Condition (ran well ) 230V, 60Cy, 3 Ph ¾”- 2-11/64” possible spindle ( 50mm currently in machine) 7.5 HP 4 speeds (4k/6k/8k & 10k Reversing spindle 13” wide Steel Sliding Table 3 Pneumatic hold down clamps 4-1/2” dust chute Foot Brake 4 Hold down springs, Mounting Collars & Bolts, Miter gauge w/Stop Rod. Capable of doing arch moulding work. 1500 lbs (?) 84”L x 60”W, x 60”H

Approximately 27" width capacity 1/2" - 3.9" diameter capacity 10 HP spindle motor 1800-3200 spindle speed 3 HP hydraulic feed PLC sequence controller

3" - 41" length capacity 1" - 3" square or round diameter capacity 15 HP spindle motor Spindle speeds 2250, 3200, 3525, 4625 rpm hopper feed

12' Arm 250 Lbs Capacity 4 HP Pump Per owner: head only turns horizonally

Gorbel 500 Lbs Ceiling Hoist

Equipped with Glue Head

8 foot bar 11HP electric motor 480 volt 3 phase

6' x 14' capacity 4 HP motor 220 volt 3 phase stop system on base

Griggio C250 Rip Saw 250 mm Wide belt (10")

24” width capacity 5HP motor 6” drums 11fpm

7.5 HP 220/440 volt 3-phase wired 220 volt 10” dust inlet Total filter serface 261 sq. Ft. 99.9% effective at .2-2.0 microns 3468 cfm @4.3” static pressure

3 HP motor 20” x 24” tilting table 20@ wheels 20” throat 13-7/8 cutting height rack & pinion guide adjustments 154-1/2” blade

Grizzly 12" Resaw

Grizzly 24" Band Resaw

There are (7) Table available.

Haimer TD2002

The Vantec 2800mm Spindleless Veneer Lathe is designed to process veneer for plywood production from both hard and soft logs. Its metal tempered grooved rollers and lathe knife inclination system work perfectly to make sure there will always be a precise contact area between the lathe knife and the log during the peeling process by eliminating vibration that could cause damage to the Veneer sheets. Vantec Spindleless lathe proves its efficiency by delivering consistent thickness variation and a impressive top linear speed of 180 m/ min throughout the peeling process for face or core veneers with smooth surfaces. - Log diameter up to 600 mm; - Max log length: 2750 mm; - Min log Length: 2300mm; (with stacker) - Min log length:1800mm (no stacker); - Veneer thickness: 1.0 to 4.0 mm; (Pine and eucalyptus); - Log core after peeling: 40 to 45mm; - Maximum linear speed 180 m/min; - Drive panel included; - Each motor is individually connected by a Variable Speed Drive for torque control in two points of traction on the rollers to pre- vent excessive load on tip ends; - Log Central aligner with maximum of 2200 mm of movement; - Pneumatic scriber Knives (02 fitted on the sides to cut in width and 01 in the Center to cut the length); - Width: 7640 mm; - Length: 3400 mm; - Height: 2550 mm; - Approximate weight: 14000 kg.

The Vantec Automatic Rotary clipper is designed to clip 2800 mm veneer sheets into specific sheet sizes as per the auto stacker preselection. It comes with electronic drive panel, automatic gauge system, positioning of clipper knife by Servomotor and encoder. It is de- signed to work with one tensioned clipper knife with gear motor. It also comes with a 2 HP motor on the output. The clipper knife is not included. - Veneer Thickness : 1 to 4 mm; - Max. Log: 2.750mm; - Minimum veneer width cut: 800 mm; - Max. Veneer length cut: 2700 mm; - Min. Veneer length cut: 700 mm; - Min. Venner rounding length: 150 mm; - Rotor gear motor: helical gears; - Clpper rollers power drive: 4 hp 6P; - Outlet conveyor Motor: 2hp 4P (input) 1 hp 8P (output); - Clipper Servomotor: 40 Nm (2x); - Width: 4800 mm; - Length: 6000 mm; - Height: 1700 mm; - Approximate weight: 7.000 kg