Holz-her 1315 Edgebender

Holz-her edgebander This machine is still under power and available for inspection.

Holz-her Cut 85 Panel Saw; under power until 8/21 model 6210

Manufacturer Specs - Cartridge glue system, automatic magazine coil & strips (1903), 3 mm PVC capacity. - Pneumatic guillotine for coil cutoff. - Double-motor end trim (1918), chamfers 0° - 10°, includes pcs changeover system. - Universal top & bottom fine trim (1942m) for bevels from 0° - 15°; allows simultaneous bevel & profile trimming top & bottom. - PVC scraper unit (1929) with 3mm inserts. - Top & bottom buffing (1940). - Complete with PLC for easy setup & program storage. - Fixed outboard panel support. - Solid state frequency converter and sound enclosure.

Holzma HPL11 Rear Load Panel Saw Still under power. Ready to be removed the end of January 2024

Holzma OPT.HpPS81/38 Panel Saw

- SAW BLADE PROJECTION 3.2" - CUTTING LENGTH 126" - PROGRAM FENCE SPEED 295 ft/min - SAW CARRIAGE SPEED 492 ft/min - MAIN SAW MOTOR 18.5 HP - SCORING SAW MOTOR 3 HP - AVERAGE TOTAL AIR REQUIREMENT 4.3 cfm - COMPRESSED AIR REQUIREMENT 87 psi - EXTRACTION SYSTEM 1port 960 cfm - TOTAL CONNECTED LOAD 27 HP - WORKING HEIGHT 36" - AIR TABLES (3) 3/4 x 85"

Optimat KFL 526/6/A3/30 Wiring Diagram: 0-202-09-6535 Supply: 480y/277V 3 Phase - 60HZ Largest Motor: 13A Largest Heater: 6A Enclosure: 12

Optimat KFL 526/6/A3/30 Wiring Diagram: 0-202-09-5610 SOO Supply: 480Y277 3 Phase - 60HZ Largest Motor: 13A Largest Heater: 8A Enclosure Type: 12

Homag Vantech 512 CNC Router Infeed lift table Outfeed conveyor 5'x12' Table Boring Block

Homag Optimat NBP084/ Vantech 480 4x8 Bed 12 HP Spindle 7-Position Boring (2) Vacuum Pumps Clean Machine

Homag Centateq N300 CNC Router 5 X 10 Infeed system Outfeed table Boring block (2) Vacuum Pumps Main Hours: 1,101 Secondary Hours: 370

- Min. panel height 0.47 inch - Max. panel height 1.57 inch - Min. edge thickness 0.01 inch - Max. edge thickness 0.24 inch - Max. forward feed speed 82.02 ft/min - Top pressure with rubber belt - No. Panel Sizing / Milling units 2 Pre-milling unit - Lamps to preheat the side of the panel - Edge coil magazine - Gluing system - glue pot for EVA hot melt glue - premelter for EVA hot melt glue - QA65 - Roller set to press the edge - no. pressure roller 7 - with positioning by NC No. Edge Processing Units 6 First Processing Unit - End trimming Constructor model HL81 - no. motors 2 - with positioning by NC Second Processing Unit - top and bottom rough trimming - no. motors 2 - with positioning by NC Third Processing Unit - Multi Function trimming and corner rounding - Constructor model - FK11 - no. motors 2 - with positioning by NC Fourth Processing unit - edge scraping - with positioning by NC Fifth Processing Unit - glue scraping - with positioning by NC Sixth Processing Unit - buffing - no. motors 2 Spray unit Control system Power Touch

Weeke Model Optimal BHX050 Vertical CNC Machine 8 Vertical Drilling Spindels 2 Horizontal Spindle in X-Direction 1 Horizontal Spindle in Y-Direction Grooving Saw in X-Direction 1 Powerful 5kW ETP 25 Routing Spindle Vector Speed: X-30M/Min Y-30M/Min Z-15M/Min

Homag Centateq N300 CNC Router 5x10 Table Offload conveyor Schmaltz overhead gantry system

Homag D-200 Drill & Dowel Inserter

Homag Optimat NBP084/ Vantech 480 4x8 Bed 12 HP Spindle (replaced in 2019) 7-Position Boring (3) Vacuum Pumps Clean Machine

Homag BMG 311 Venture 316L CNC

Homag Espana CH-03/32/32-PLUS Panel Saw Still under power and available for inspection. 230/480 V

As Taken From Service: Includes return conveyor