Boring/Inserting aggregate travel on profile bearing guides with: 3 spindle boring unit – Horizontal 1 Spindle Routing unit – Horizontal 1 Blowing, gluing, dowel inserting unit for a single selected dowel 6 – 12mm diameter, 25 – 60 mm length – Horizontal Barcode reader Fully automatic electronically controlled central lubrication Closed gluing system with variable setting of glue amount by touch screen Selector switch GLUE/WATER for quick rinsing of entire system 1½ gallon glue Stainless steel container 1½ gallon water Stainless steel container Glue control warning light 1 Right-hand stop, 1 left-hand stop, and 1 center stop, all removable (3) Starting buttons for individual processing of 1-4 work pieces (8) Pneumatic clamping cylinders for work piece thickness max 80mm, work piece length minimum 70mm 1 Exhaust ducting, with connection diameter 80mm Programming by menu-based software; Beckhoff 15? Touchscreen display Operating system: WINDOWS 7

Gardner Denver Air Compressor - 25 HP - Gardner Denver Air Dryer - 250 Gallon reservoir and stand

Generac 200 HP Genset

Giben K305 Edgebander Manufacturer specs (to be confirmed): Standard Configuration Panel Thickness: 10~60mm Edge Thickness: 0.4~3mm Motor Power: 2.35Kw Maximum Curve Radius: 20mm Cutter Maximum Range: 50mm Working Pressure: 0.6 MPa Outline Dimension: 960 x 950 x 1000mm Gross Weight: 280Kg Voltage: 220-480V

Go Fast 5-Head Resaw Unit was cut into two pieces and can be put back together with a weld in the middle. Approx layout is 31' x 8'

Go Fast Resaw 15 HP Motor Put under power to test, never put into production.

GoFast 2-Head Resaw 10 HP main motors Go Fast Board Deduster

2023 Go Fast 6x12 Resaw Has minimal use

Good/Fair Condition (ran well ) 230V, 60Cy, 3 Ph ¾”- 2-11/64” possible spindle ( 50mm currently in machine) 7.5 HP 4 speeds (4k/6k/8k & 10k Reversing spindle 13” wide Steel Sliding Table 3 Pneumatic hold down clamps 4-1/2” dust chute Foot Brake 4 Hold down springs, Mounting Collars & Bolts, Miter gauge w/Stop Rod. Capable of doing arch moulding work. 1500 lbs (?) 84”L x 60”W, x 60”H

Approximately 27" width capacity 1/2" - 3.9" diameter capacity 10 HP spindle motor 1800-3200 spindle speed 3 HP hydraulic feed PLC sequence controller

3" - 41" length capacity 1" - 3" square or round diameter capacity 15 HP spindle motor Spindle speeds 2250, 3200, 3525, 4625 rpm hopper feed

12' Arm 250 Lbs Capacity 4 HP Pump Per owner: head only turns horizonally

Gorbel 500 Lbs Ceiling Hoist

Equipped with Glue Head

8 foot bar 11HP electric motor 480 volt 3 phase

6' x 14' capacity 4 HP motor 220 volt 3 phase stop system on base

Griggio C250 Rip Saw 250 mm Wide belt (10")

3 HP motor 20” x 24” tilting table 20@ wheels 20” throat 13-7/8 cutting height rack & pinion guide adjustments 154-1/2” blade

7.5 HP 220/440 volt 3-phase wired 220 volt 10” dust inlet Total filter serface 261 sq. Ft. 99.9% effective at .2-2.0 microns 3468 cfm @4.3” static pressure

24” width capacity 5HP motor 6” drums 11fpm