Quick Heavy Duty Pneumatic Clamp Carrier with 20-sections and 12-1/2' width capacity. -- (8) Heavy Duty zinc plated clamps per section for 10 section, clamp opening 44" -- (10) Heavy Duty zinc plated clamps per section for 10 section, clamp opening 44" -- Includes 180 clamps with 44" openings and 3.5" high x 4-3/4" wide jaws with 1° inward draft. -- Pneumatic overhead panel flattener along with tightener -- Pneumatic panel flattener for second operator -- Semi-Automatic Pneumatic clamp tightener . -- Semi-Automatic panel tightener for second operator -- Single button automatic electric motor rotation cycle with indexing. -- Heavy Duty frame with 3" diameter shafts and 6" I-beam legs. -- Includes foot levelers, coiled air lines, flexible conduit for electric wires, automatic air line oiler, high quality urethane finish coating and tool box with spare parts & tools.

QUICK 14-Section Heavy Duty Hydraulic Clamp Carrier with 20-1/2' width capacity With (16) Standard zinc plated clamps per section (224) clamps total), 38" opening on clamps Standard Features include: -- Clamps jaws are 3-1/2" high x 4-3/4" wide with 1° inward draft to keep stock securely held down. Clamps use 3/4" dia. full-length screws; corrosion resistant, zinc plated, full box frame. For face gluing, Rocking Plates available as optional equipment -- Pneumatic Panel Flattener with easy to use controls. -- Pneumatic panel flattener for second operator -- Hydraulic Clamp Tightener; 3,000 RPM air wrench is 5 to 10 times faster than competitive tighteners; two-handed, trigger activated tightener is more confidence inspiring than the old ergonomically awkward "swing-style" clamp tighteners. Fast tightening and full-length clamp screws eliminate need for manual adjustment of rear clamp jaws. -- Hydraulic clamp tightener for second operator -- Electric Motor Rotation; push button, automatic cycle with indexing. Automatic Rotation Cycle includes entire sequence; reverse rotation, front-rest out, forward rotation, front-rest in, and lay clamps on front rest. Perfectly! Every time! Complete with:Foot levelers, coiled air lines, flexible conduit for electric wires, automatic air line oiler, high quality urethane finish coating, and tool box with spare parts & tools. 14-Section Clamp will produce 300 panels

Quick Heavy Duty 14-Section Hydraulic Clamp Carrier, 16-1/2' Wide -- 14-Section Clamp Carrier 16-1/2' width cap.. -- (12) Heavy Duty zinc plated clamps per section for (168) total clamps. -- 38" opening on clamps; jaw sizes on clamps are 3-1/2" high x 4-3/4" wide with 1° inward draft. Equipped with: -- Dual Overhead Pneumatic Panel Flatteners for (2) operators -- Dual Hydraulic Clamp Tighteners for (2) operators -- Automatic Electric Motor Rotation with Indexing. -- Standard features include: Foot levelers, coiled air lines where used and flexible conduit for wires.

QUICK 14-Section Pneumatic Clamp Carrier with 8-1/2' width capacity With (6) Standard zinc plated clamps per section (84 clamps total), 32" opening on clamps Standard Features include: -- Clamps jaws are 2-1/2" high x 4-3/4" wide with 1° inward draft to keep stock securely held down. Clamps use 3/4" dia. full-length screws; corrosion resistant, zinc plated, full box frame. For face gluing, Rocking Plates available as optional equipment -- Panel Flattener with easy-to-use controls. -- Pneumatic Clamp Tightener; 3,000 RPM air wrench is 5 to 10 times faster than competitive tighteners; a two-handed, trigger-activated tightener is more confidence-inspiring than the old ergonomically awkward "swing-style" clamp tighteners. Fast tightening and full-length clamp screws eliminate need for manual adjustment of rear clamp jaws. -- Electric Motor Rotation; push button, automatic cycle with indexing. The automatic Rotation Cycle includes the entire sequence; reverse rotation, front-rest out, forward rotation, front-rest in, and lay clamps on front rest. Perfectly! Every time!Complete with: -- Foot levelers, coiled air lines, flexible conduit for electric wires, automatic air line oiler, high-quality urethane finish coating, and toolbox with spare parts & tools. -- 14-Section Clamp will produce 300 panels per shift; 20-Section machine, 500 panels per shift.

QUICK 6-SECTION Clamp Carrier; (6) Sections, (6) clamps per section, and 8-1/2' width capacity. -- (36) Clamps total with 50" opening and 2-1/2" high x 4-3/4" wide jaws with 1° inward draft. -- 8 1/2 feet wide with easy to use controls.Equipped with: -- Pneumatic Clamp Tightener; 3,000 RPM air wrench is (5 -10) times faster than competitive tighteners; 2-handed, trigger activated tightener is more confidence inspiring than the older, ergonomically awkward "swing-style" clamp tighteners. -- Pneumatic Panel Flattener -- Electric motor drive for Carrier rotation.Complete with: -- Foot levelers, coiled air lines, flexible conduit for electric wires, automatic air line oiler. -- Hhigh quality Urethane finish coating, and tool box with spare parts & tools. NOTE: -- 6-Section Clamp typically produces (144) high quality edge glued panels per day (3 panels per section x 6 sections x 8 hours). -- Clamp can be expanded to (14 or 20) sections at a later time. 14-Section Clamp will produce (300) panels per shift; 20-Section machine, (500) panels per shift.Floor space requirement: 134"w x 142"d x 143"h

QUICK 40-Section HEAVY DUTY HYDRAULIC CLAMP CAFRRIER with 8-1/2' Width cap. -- Clamp Carrier with: (6) Clamps per section, (240) total Heavy Duty zinc plated "Quick-Adj" fast adjusting clamps; 32" opening on clamps; jaw sizes of clamps are 3-1/2" high x 4-3/4" wide, with 1° inward draft. -- Equipped with: Integral pneumatic panel flattener and fully automatic hydraulic clamp tightener with adjustable torque limiter. -- Single-button automatic Heavy Duty electric motor rotation with cycle indexing. -- Automatic Carriage traverse is powered by a hydraulic motor coupled to a rack & pinion drive system, which provides smooth, accurate and very quiet operation. -- Automatic Carriage includes its own control panel for easy operator control at the Carriage; this is particularly helpful during "semi-automatic" operation. -- Operation: The machine automatically flattens panels, tightens clamps, rotates, and loosens clamps. After loading wood into a section of clamps, the operator presses the "Cycle Start" button. -- The hydraulic Automatic Carriage traverses from right-to-left, flattening panels and tightening clamps along the way. -- When the carriage reaches the end of its traverse, the machine performs an automatic rotation cycle, bringing the next section of clamps down to the operator's position. -- The carriage then traverses from left-to-right, loosening clamps on the way back to its starting point. -- Standard features: All structural & mechanical components are manufactured with very Heavy Duty materials, providing many years of reliable service. -- Heavy Duty frame with 3" dia. shafts and 6" I-beam legs. -- Supplied with: Foot levelers, coiled air lines, flexible conduit for electric wires, automatic air line oiler, high quality urethane finish coating, and tool box with spare parts & tools (QUICK Model "A-CCFH-08.5-40").

QUICK 20" Wide Conveyorized Glue Applicator -- 20" wide grooved rubber glue applicator roll with stainless steel doctor blade and glue reservoir. -- Features easy adjustment or removal of doctor blade, 16' overall length, 8' infeed before the glue roller and 8' outfeed conveyor. -- Equipped with: Heavy Duty 0.25 HP motor drive for slat-type conveyor and glue roll, limit switch with wand for automatically stopping the slat bed conveyor when stock reaches the Clamp Carrier, adjustable safety slip clutch. -- Complete with: Foot levelers, Heavy Duty crossbars, chain guard, high quality anti-stick urethane finish, and owner & operator's manuals.

QUICK 30-Section HEAVY DUTY Pneumatic Clamp Carrier with 8-1/2' width cap. -- (6) Heavy Duty zinc plated clamps per section for (180) total clamps, 38" opening on clamp. -- Jaw sizes on clamps are 3-1/2" high x 4-3/4" wide with 1° inward draft.Equipped with: -- Pneumatic overhead panel flattener, -- Pneumatic clamp tightener, -- Electric motor rotation with indexing.Standard features include: -- Foot levelers, coiled air lines where used, and flexible conduit for wires.

SCM OLIMPIC K230-EVO SINGLE SIDED EDGEBANDERSpecifications: --0.4mm to 3mm Edge thickness, Panel thickness 8mm to 50mm (3/8" to 1-15/15"), minimum part width 110mm (4.33"), minimum part length 160mm (6.30"). -- Equipped with: -- 1.5 Kg Teflon-coated glue pot, glue roller application system complete w/automatic recycling device for unused glue, digital thermostat adjustment for temperature control. pneumatic guillotine, 3-Roll pressure unit w/pneumatic controls for all pressure rollers. -- Automatic strip & coil feed magazine --Workstations: --÷Double motor front & rear (0.4 HP - 12,000 RPM motor ea.), tilts 0° - 15°, end trimmers mounted on 45° THK guide. --Top & bottom flush & bevel trims with quick release mount and plug-in motors for quick tooling changes (0.7 HP - 12.000 RPM motor ea.), bevels 0° - 15° with precision digital indicators for quick setup. --Top & bottom scraping unit w/pneumatic positioning from the control panel. -- Top & bottom buffing unit (0.25 HP - 2,800 RPM motors). 29.5FPM Fixed feed speed, 0.75 HP feed drive.

SCM TECH Z 30 CNC MACHINING CENTER (W/ATC/BORING): -- Specifications:Working Field "X" axis 120" (3,050 mm); "Y" axis 52.7" (1,340 mm) for routing & 44" (1,118 mm) for boring; "Z" axis stroke 7.8" (200 mm); max. material thickness 3.9" (100 mm). -- Positioning Speed:"X" & "Y" Axes are 197 FPM (60 MPM); "Z" axis is 72 FPM (22 MPM).Axes positioning by: AC Brushless motors and YASKAWA drives; high precision ball screw drive system in "X", "Y". "Z" Axes;All axes ride on prismatic guideways & sliding blocks. -- Worktable:(6) "TV" Tubeless mobile support rails, (2) vacuum pods per rail; (4) pneumatic lifter rails for heavy panels.(6) Pneumatic pop-up backstops, (6) pneumatic pop-up front stops; (2) pneumatic pop-up side stops.LED Display positioning assistance for the support rails & vacuum pods; (2) independent working fields. -- Boring Head:3 HP (2.2 kW) motor - 4,000 RPM; (15) independent vertical spindles: (8) Spindles in "X" & (7) spindles in "Y".(6) Horizontal spindles (2 + 2) in "X" & (1 + 1) in "Y-axis".(1) X-axis grooving saw with 100 mm dia. blade - 6,000 RPM. -- Machining:(1) 10 HP (7.5 kW) Electro-spindle router with: HSK F63 Adaptor; variable speed from 1,000 - 24,000 RPM, max. torque achieved at 12,000 RPM.Static inverter for stepless speed & rapid shutdown rotation.(1) 6-Position ATC tool plate mounted on the on the machine for "on the fly" ATC; max. tool weight is 8 kG (17.6 Lbs). -- Operator & Machine Control:PC Front-End with: SCM "UNIVERSAL K2" + "Xilog Plus" + Windows "XP" Pro Operating System; 15" CRT color display, CELERON 2 GHz processor, enclosed in air-conditioned cabinet. -- Complete with:(1) 100 m³/Hr Vacuum Pump; automatic lubrication system; "BUMP STOP" safety system. -- Actual Model is SCM TECH Z30 R6

SCM Sandy 10 -RCS-110 Wide Belt Sander (2) Heads43" Width cap. Drum, Combination HeadHead Configuration:1st. Head: 7" diameter corrugated metal roller for calibration 35 HP ( Drives both Heads )2nd Head: Combination head with 7" dia. contact roller (spiral grooved rubber covered); air/jump finishing platen controlled with timers to eliminate any rounding on leading & trailing edges of the panel, 2" wide platen.Specifications --103" long x 43" wide Abrasive belts --Air tracking, floating & rigid bed for sanding of veneers & solid panels; infeed & outfeed spring loaded holddown rolls -- Minimum workpiece length 16" --Thickness capacity 6.25". --Separate 2.5 H.P. variable speed feed motor delivering feed speeds from 15 to 70 FPMNote: The seller has 20 boxes of various sandpaper belts (80 – 150 grit) that will be included.

SCM SANDYA - 40 M3 135, ...3-Head Wide Belt Sander 52" Width cap. Drum, Drum, Combination HeadHead Configuration:1st Head: Steel Contact 22 kW Pneumatic blowdown and alignment.2nd Head : Rubber Contact 18.5 kW Pneumatic blowdown and alignment.3rd Head: Combination Platen 15 kW Pneumatic blowdown and alignment.Note:The SCM sander does not have a brush. After the 3rd head, it has this pneumatic blow-off bar with multiple blow-offs running the length of the sanders width. Sander can be seen under power if needed.Specifications: -- 53" x 103" Abrasive belts with electronic tracking. -- All heads with abrasive belt grit compensation. -- Conveyor belt feed with dual feed speed, 5 HP motor. -- Automatic part thickness adjustment. -- Motorized thickness opening via (4) precision conveyor bed jacks with LED readout. --0" - 7-7/8" opening. -- Equipped with & Features -- Outfeed rubber covered holddown rolls or shoes on all heads. -- Motor load meters. --Infeed and outfeed conveyor extensions. -- WYE-DELTA soft start.Note: The SANDYA model "40" is more or less the same as the SANDYA "30" but more Heavy Duty.

SCM SANDYA 15S (3) Head Wide Belt Sander42" Width cap, Drum, Drum, Combination HeadHead Configuration:1st Head: Steel contact roll, 7" dia., 35 HP motor;2nd Head: Rubber-covered contact roll, 24 HP motor3rd head: Combination head, rubber-covered contact roll (45 Shore) and 3" wide finishing platen, 17.4 HP motor.Specifications: -- 43" x 103" Abrasive belts -- Electronic tracking & pneumatic belt tensioning, abrasive belt grit compensation. -- Conveyor belt feed with dual feed speed, 4 HP motor -- Automatic part thickness adjustment -- Motorized thickness opening via (4) precision conveyor bed jacksEquipped With & Features: -- LED readout, 0" - 6-1/4" opening. -- Infeed & outfeed spring loaded rubber covered hold-down rollers -- Motor load meters -- Infeed and outfeed roller conveyor extensions.

SCM PRATIX S-12-B FLAT TABLE MACHINE (W/ATC/BORING): -- SpecificationsSingle 4' x 8' traveling "Bridge Gantry" and stationary aluminum dual-vacuum table with: "MATRIX" square grid pattern for fixturing parts.Grid pattern allows use of vacuum pods or closed cell rope gasketing material and use of spoil-boards for "nested base machining".Part location pop-up pins mounted on the table perimeter. -- Working field:"X" Axis is 98" (2,486 mm); "Y" axis is 49.4" (1,255 mm); "Z" axis stroke is 9.8" (250 mm); max. material thickness 5.9" (150 mm). -- Positioning Speed:"X" & "Y" Axis 115 FPM (35 MPM), "Z" axis at 82 FPM (26 MPM); closed loop AC Servo drive system.High precision "Rack & Pinion" system in "X" & "Y" axis & ground ball screws "Z" axis; all axes ride on extra-large precision profile linear guideways. -- Boring Unit:3 HP (2.2 kW) - 6,000 RPM motor; (7) vertical spindles on 32 mm centers, (5) spindles in "X" axis & (2) spindles in "Y" axis. -- Machining:(1) 9 HP (6.7 kW) Air-cooled electro-spindle with HSK F63 adaptor; variable spindle speeds from 1,500 - 24,000 RPM.(1) 7-Position ATC tool rack mounted to the machine base RH side. -- Operator & Machine Control:PC Front-End with: "XILOG Plus" + Windows "XP Pro" Operating System; 17" high resolution LCD; ergonomic keypad.USB Ports, serial ports RS-232 & RS-242 & Ethernet adaptor; programs can be transferred via disk or downloading by wire is possible.All computer components are mounted on a mobile stand.XILOG Plus Offers incredible list of functions from: (a) Auto-diagnostic to (z) zooming; controlled acceleration & deceleration, encoder feedback, dynamic tool correction via PLC due to active tool wear using space-and-time criteria. -- Additionally Equipped with:Onboard mini-CAD with built-in programming for writing: Circles, ellipses & angles with only a few keystrokes.Onboard cycle optimization, onboard calculator, mirror-imaging, and repeat imaging. -- Complete with:(2) 150 cbm Vacuum Pumps; safety enclosure around the spindle carriage. Tool length measuring device.(1) Universal remote Pendant; 7" color display allows for the effective management of all machine functions from manual Jog Mode to loading & execution of a program. The pendant is fitted with a USB port to allow quick load & setup of new programs.Safety "bump-stop" bumpers; emergency stop rope, doc's & manuals. -- Actual Model: SCM PRATIX S-12-B

SCM OLIMPIC K360 EDGEBANDER (W/PRE-MILLING):Specifications -- Edge Capacity: 0.3 - 3 mm (0.012 - 0.118"); for coiled edges: 0.3 - 6 mm strips with: 6 x 60 mm kit included; dia. coil holder plate: 780 mm (31"). -- Panel Capacity. Min. width: 90 mm; min. length: 140 mm (3-1/2" & 5-1/2"); panel thickness min./max.: 8 - 50 mm (3/8" - 2") & max. 60 mm (2.4") with 6 x 60 mm kit included.Equipped with: -- Adjustable Infeed Fence: Manually preset with digital indicator; pneumatic in/out positioning. -- Premilling Station - "RT-VP": Spindles: (2) x 2.0 HP - 19,000 RPM; (1) PLC controlled jump action; diamond cutterheads. -- Automatic Strip & Coil Feed Magazine: For straight edges; 3 mm guillotine for coils. -- Gluing Station for EVA (Hot Melt) with: Teflon-coated glue tank; quick disconnect to change glue tanks fast if needed; Heat-up time approx. 10 Min. Includes 1.5 kG glue pot instead of standard. -- Pressure Section: Manual digital positioning, (3) pressure rollers: 1st Larger; Teflon Coated and powered. Workstations -- End Trimming Station - "K2". Front & rear: (2) x 1/2 HP (included extra); 12,000 RPM Motors mounted on THK guides; swivels 0° - 15°; rapid setup between straight & angled cutting with the automatic swivel cylinder.Automatic positioning for (3) cutting modes: Straight, chamfered, and radius of thick edges. -- Top & Bottom Trimming Unit - "R-K". Remote (via control panel) pneumatic positioning for (3) settings: Flush/bevel/radius trimming; (2) x 0.7 HP - 12,000 RPM motors with precision digital indicators for quick setup. -- Top & Bottom Profile Scraping Unit. Manual preset with: Digital indicators; large dia. copy wheels for max. accuracy; pneumatic in/out positioning. -- Buffing Unit - "SP-V": Top/bottom; (2) x 1/4 HP - 2,800 RPM Motors; tilting up to 12°; cleaning & polishing of edges.Controls -- ORION - "1" Plus: Controller. Fixed at infeed of machine; soft keys; graphics; 4" LCD display panel.Handles most machine setup functions & workstations; machine automation by PLC function; encoder positioned in the panel feed track pinion; diagnostics for a quick solution to many errors; process statistics data: Number of pieces/edges and track feeding.Features & Complete with: -- Feed speed: 36 FPM Fixed; (1) x 2.0 HP feed drive motor; 200 Hz frequency inverter for all trimming units; manual adjustable holddown pressure beam; full sound enclosure cover; outboard panel support. -- Overall dimensions: 3,600 mm (142") x 900 mm (36") x 1,600 mm (63"); approx. weight: 997 kG (2,200 Lbs). -- UL/CSA approved version.

SCM ACTION FL 2500 CASE CLAMP (SEMI-AUTOMATIC): -- SpecificationsMax. standard working dimensions: 2,500 mm (98.4") Wide x 1,250 mm (49.2") high x 800 mm (31-1/2") depth. -- Min. standard working dimensions: 250 mm (9.8" Wide x 250 mm (9.8") high x 150 mm (5.9") depth. -- Working height: 508 mm (20"). -- Vertical pressing force: 15 KN (3,372 Lbs.).Features -- Full top & bottom platen for maximizing pressing PSI on the box. -- Rack & Pinion guides at all (4) corners of the top platen & side pressure to keep the top platen parallel and the side pressure square. -- Sizes of box can be input for efficient cycle control when running repetitive box closings. -- Machine can also find the size of the box, so all the Operator has to do is open the Clamp to a size larger than the box to be clamped. -- The vertical & horizontal pressure is adjustable according to the type of furniture to be assembled. -- Machine is equipped with: (3) Side pressure bars & able to sequence different furniture pieces without manual intervention. -- Pressure supplied by infinitely adjustable brushless electro-motors.Complete with: -- 5.7" Touchscreen panel with: Software by CPC in order to program cycles. -- Rack & Pinion system, brushless motors. -- Front & rear photocell barriers. -- Actual Model is: SCM CPC ACTION FL 2500

SCMI MINI MAX - Formula S 2: Sliding Table SawSpecifications & Features -- 128" Cutting cap. w/standard scoring saw and carriage; 5 HP motor; stop on fence for cuts extendable to 128"; 50" cutting width w/ rip fence.Equipped with: -- 14" Main blade; 4-1/2" scoring blade; 4-1/2" max. blade cutting height at 90°; 3-1/2" max. blade cutting height at 45°. -- 4,000 RPM Main blade speed; 8,500 RPM scoring blade; 90° - 45° blade tilting.

SCMI - K201 HFE: Single Sided Edgebander1/8" Max. edge cap.; 1-1/2" max. panel thickness; semiautomatic strip & coil feed magazine (manual single strip feed); Teflon coated glue pot w/fast 8-Minute heat up time; 1.2 mm cap. guillotine. -- Workstations: Single motor front & rear end trim; 0.8 HP - 10,000 RPM motor; top & bottom flush trims, 0.8 HP - 27,000 RPM ea. motor; straight or 12° bevel cutters. -- Top & Bottom buffing unit, 0.25 HP - 2,800 RPM motors; 25 FPM fixed feed speed with 0.8 HP drive. -- Complete with: Sound enclosure, frequency converter, and used tooling.

SCM - Concept 2000, ...Double End Tenoner.Double End Tenoner with: Jump scoring, Hogging, Shaping with stacked tooling. -- 122" Opening cap., motorized opening with keypad entry & LED readout, 12" infeed chain area in front of holddowns. -- 0" - 4" Motorized thickness opening with mechanical digital readout. -- 6" Min. width, 2-post machine. Each side equipped with: -- 1st Station: Jump scoring. -- 2nd Station: Hogging unit. -- 3rd Station: Coping head with stacked tooling capacity (manually operated). -- 4.5 HP Drive for 10 - 60 FPM variable feed speed. -- Chain dogs on 15-3/4" centers, rubber top nonmarring chain pads. -- Heavy-Duty chain links with: Needle bearings, automatic oil mist chain oiler, automatic brake on feed motor with emergency stop.Complete with: -- Upper driven holddowns with: Continuous feed belts; feed beams can be disengaged for conventional part feeding in front of dogs. -- Mobile remote control for setup; dual lead screw for traversing beam; exhaust hoods on all heads.Note: Tear down and loading not included.

SCM SANDYA 7 RCS Wide Belt Sander2-Head, 42" cap. - Great solid wood finish Sander. -- 1st Head: Grooved steel contact roll, 6-1/4" dia., 30 HP motor -- 2nd Head: Combination head, rubber covered contact roll, 6-1/4" dia. (65 Shore), and 2" wide finishing platen, 25 HP motor. -- 43" x 75" or 85" Abrasive belts with electronic tracking & pneumatic belt tensioning, pneumatic exclusion of all contact rolls. -- Conveyor belt feed with variable feed speed, 14.5 - 30 FPM, 1.5 HP motor, automatic part thickness adjustment, -- Motorized thickness opening with LED readout,0" - 6-1/4" via (4) precision conveyor bed jacks. -- Infeed & outfeed spring loaded rubber covered holddown rolls on all heads, -- Motor load meters, infeed and outfeed conveyor extensions, WYE-DELTA soft start.