SANI-TECH - SC1040/30, ...Auger Compactor -- Motor: 10 HP. -- Hopper capacity: 4.3 Cubic yards. -- Auger RPM: 10. -- Displacement rate: 270 Cubic Yards/Hour. -- 20-Yard Compactor

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"

5 HP motor with 8" or 10" blade cap. -- Features: SawStop Safety System, blade stops and retracts on accidental contact, protection is always on, performs continuous self checks, invisible protection, does not interfere with work, compatible with all standard blades; works on all woods and non-conductive materials. -- Includes bypass switch for cutting metal. European style riving knife to minimize kickback; Low profile blade guard for narrow cuts; Quick-change mount for guard and riving knife ÷Large start/stop paddle for hands-free shut off; Main power switch with removable lock-out key; Magnetic contactor motor control; Blade shroud for improved dust collection; Zero-clearance insert; Extra heavy castings ÷Widely spaced trunnions; Infinitely adjustable trunnion assembly for precision alignment. -- Also includes: Vertical slide blade elevation for increased stability; Long-lasting V-ribbed belts; cast iron handwheels; Two access doors in cabinet; Powder-coated cabinet.

SCHELLING FXH 430/410 FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications:169" (4,300 mm) Cutting length & 167" (4,250 mm) pull back; 3.9" (99 mm) max. saw blade projection, 23 HP (17 kW) main & 3.5 HP ((2.6 kW) scoring motor. -- Saw Carriage: Electronically controlled saw carriage with rack & pinion drive; variable travel speed 1 - 394 FPM (1 - 120 MPM), constant return of 394 FPM (120 MPM). -- Pusher Fence: Electronically controlled overhead pusher fence, rack & pinion driven on both sides; (9) Gripper clamps that open up to 3.5" (90 mm). -- Forward speed 0 - 262 FPM (0 - 80 MPM), return speed 262 (80 MPM) FPM; travel via brushless AC Servo Drive -- Operator & Machine Control:PC Front-end with Schelling "MCS" + Windows "NT" operating system.17" Color display with SVGA resolution (displays cutting dimensions & patterns w/moving graphics); virtually unlimited storage capacity, standard keyboard & mouse.Ethernet card; 128 MB Ram, 56K modem. Integrated graphical self-diagnostic, remote diagnostics by the factory is possible via dedicated phone line; data input by keyboard or possible direct downloading from office PC.SCHELLING "MCS" software displays simulation of patterns before actual cutting; graphical representations of cut-to-size parts in production shows the operator what to do in "real time". -- Complete with:2,300 mm Long crosscut fence (front-to-back), (2) automatic side/crosscut aligners for up to 87" (2,210 mm) crosscuts, (1) in front & (1) behind pressure beam cut line.(3) Front mounted air floatation tables, each table 24" x 83" (609 x 2,108 mm), rear of machine fully enclosed for safety with man-height safety fencing. -- Actual Model is SCHELLING FXH 430/410

SCHELLING FM-430/410 CNC Front Load Panel SawSpecifications & Features: 169" (4292 mm) Cutting length & 165.3" (4,200 mm) pull back, 3.75" (95 mm) max. saw blade projection; 25 HP (19 kW) 4,100 RPM main & 3.4 HP (2.5 kW) 5,600 RPM scoring motor. -- Equipped with: Variable saw carriage travel speed from 0 - 278.8 FPM (85 MPM), constant return of 278 FPM (85 MPM). -- Electronically controlled overhead program fence with rack & pinion driven on both sides; forward speed from 0 - 278 FPM (85 MPM), return speed of 278.8 FPM (85 MPM); equipped with (8) gripper clamps (open up to 5" (130 mm). -- Features: SCHELLING "COMPOSER" IBM-AT Compatible Computer Control; aftermarket color monitor (displays cutting dimensions and patterns w/moving graphics) , self-diagnostic, data input by keyboard; onboard optimization program. -- Complete with: 2-3/4" to 87" (2,200 mm) Long side/cross-cut aligning zone, (1) aligner in front & (1) behind the cut line. -- (3) Front mounted air float tables for moving panel from rip section to the cross-cut section, (2) movable and (1) fixed; each with their own blower. -- Rear of machine fully enclosed for safety with man-height sheet metal panels & wire screen windows. T

Schneeberger 9 Sculptor Profile GrinderSwiss Made, Schneeberger Automated High Precision Grinder for Finger Joint, router bits, saw blades, straight and milling Cutters. Specifications: -- Grinding Motor: 1,500 - 3,000 RPM. -- Cooling Pump: 2,800 RPM. -- Grinding Wheel Speed: 3,000 - 6,000 RPM. -- Grinding Wheel Diameter: 50 - 200 mm. Grinding Wheel Bore: 30 mm. -- Cross Travel of Grinding Wheel: 200 mm. Vertical Travel of Grinding Wheel: 400 mm. -- Grinding Head: Swivel-able. -- Worktable Travel: 400 mm. -- Coolant Capacity: 25 liters.Dimensions: 1,226 mm length x 1,160 mm width x 1,180 mm height; Weight - 320 kG.10" Width cap., 11.5" dia., max. profile depth 5.5", radial clearance angle up to 35ø, lateral clearance angle up to 15°Equipped with & Features; -- 2 HP - 1,500 RPM motor, variable grinding speed 2,000 - 4,000 RPM, three-sided full jet cooling. -- All std. grinding equipment for HSS grinding, 1-1/2" spindle arbor, (2) wheel flanges, (1) knife holder, and dresser.

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

SCHUTTE 280.100 HAMMERMILL -- Type 13100P -- Rotor 24" dia. x 48" wide -- Housing 3/4" thick -- Shaft speed 3,600 rpm -- Heavy duty, statically and dynamically balanced rotor -- (96) Standard notched heat treated hammers 3/8" thick -- Also included; two screens -- Motor 125 HP -- Applications; Planer shavings, dry wood chips, etc. etc.

SCHUTTE-BUFFALO 15 Series, Model 15300 Wood Grinder;Complete with the following components and features: --Carbon Steel Construction. --Rotor approximate 44" diameter x 72" wide. --Approximately 3" wide Swinging Hammers, tip speed 20,700. --Top feed, bottom discharge. --Bottom screen approximate 5040 square inch area. --Clam shell housing. --500 HP, TEFC, 3/60/460 volt, 1785 RPM drive Motor with coupling and shaft guard. --Mounted on a heavy-duty steel Factory Frame. --NOTES: Largest model of the 15 Series. &#9679 Machine weight 16,000 Lbs.

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.

TIMESAVERS 43- 3 OB Orbital Sander3-Head, 43" width cap. with (2) Orbital heads and (1) finishing brush. -- 1st & 2nd Orbital Heads: Each orbital head with (1) 10" wide platen for a total of (2) platens, each platen features a "dual action" head with a high-speed orbit and combined back-and-forth oscillation to remove abrasive belt cross-grain scratches. -- "Quick change" system for abrasive material, (2) 7.5 HP main orbit motors, and 1 HP oscillation motor. 3rd Head: Rotary abrasive brush with 2 HP motor, single side brush wear/height adjustment. -- Conveyor belt feed with Ruff-Tex conveyor belt, variable feed speed from 5 - 20 FPM, infeed & outfeed holddown pinch rollers on all heads. -- 0" - 6" Motorized part thickness opening, constant pass line-height of conveyor bed assembly, extended infeed load area, motor load meters on sanding heads. -- Includes a DOUCET Return Conveyor System -- New transformer for 230 or 460 Volt, specifically for this machine is available at an additional cost

Timesavers 2321-45-01 (2) Head wide Belt Sander51" Width cap, Drum, Combination HeadHead Configuration1st Head: Steel contact roll, 8" dia., 30 HP motor.2nd Head: Combination head with a rubber-covered contact roll 5-1/2" dia. and 2-1/2" wide segmented finishing platen, 25 HP motor, (2) dial indicators for contact roll height adjustment.Specifications: 52" x 103" Abrasive belts, -- "Posi-Trak" electronic tracking & pneumatic tensioning, conveyor belt feed. -- 15 - 45 FPM Variable feed speed with inverter control, -- Automatic conveyor belt tracking; -- Double in-feed & out-feed spring loaded hold-down rolls.Equipped with & Features -- 0" - 5" Max. motorized part thickness opening with automatic part thickness set-up, -- Air-operated disc brakes, -- Motor load meters, -- 14" in-feed conveyor area, -- In-feed emergency stop bar."Owner's manual included

TIMESAVERS 52-20 ORBITAL SANDER2-Head, 52" width cap. with (2) Orbital heads.Specifications: 1st & 2nd Orbital Heads: Each orbital head with (2) 5" wide platens, each platen features a "dual action" head with a high-speed orbit and combined back-and-forth oscillation to remove abrasive belt cross-grain scratches. -- 1st Head: 7.5 HP 230/460V 3PH motor -- 2nd Head: Oscillating platen 7.5HP, 330/460V, 3Ph"Quick change" system for abrasive material -- Conveyor belt feed with Ruff-Tex conveyor belt, variable hydraulic feed speed from 5 - 20 FPM, vacuum bed assembly, infeed & outfeed holddown pinch rollers on all heads. -- 0" - 6" Motorized part thickness opening with mechanical digital readout, constant pass line of conveyor feed bed assembly, motor load meters on sanding heads -- Push button controlsNOTE: Feed Motor and Feed Belt have been taken apart for shippingThe above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify.

TORIT - 460-IRD-20: Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Downflow air pattern allows airflow & gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure drop.Specifications -- 20 HP Direct drive; floor mounted blower. -- Fan inlet: 17". -- CFM: 7,000. -- Set of filter bags. -- Steel elbow from fan to collector. Motor Starter included.

TORIT 360-IRD-15 Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Down flow air pattern allows airflow and gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure dropSpecifications: -- 15 HP direct drive, floor mounted blower. -- 4,800 CFM @ 8" wg, 4,050 CFM @ 9" wg, 2,400 CFM @ 10" wg -- (21) Dura-life filter bags with a cloth area of 192 sq. ft. -- (3) Collection points for plastic collection bags.

TORIT-DONALDSON ADMC AD8 DRYFLO Cartridge Dust Collector. A Mist collector designed for long-lasting high collection efficiency capture of coolant and machining oil mists in metalworking applications. Even smaller amounts of dust can be filtered in the dirty air stream. -- DRYFLO is a proprietary cartridge which outperforms electrostatic precipitators and mist collectors utilizing standard HVAC envelope and cassette filters. Filter unit features a unique air-side filter retention system allowing for quick filter changes with minimal worker contact with collected oil. -- Also feature three-stage Filtration via a.) prefilter, b.) wrap allowing, c.) the filter cartridge to drain and coalesce smaller coolant mist droplets in to larger droplets. Plus optional fourth stage HEPA filters available for applications where smoke exists or additional efficiency of discharge air is required. -- Overall data: Capable of 17,600 CFM; (8) Filter Cartridges, 1,760 sq. ft. of filter area, -- Complete with: Ground mounted fan powered by a 40 HP motor, belt-driven. Fan includes a variable volume inlet. In prior application clean air was not retruned to building. -- Blower currently setup for approx. 15,000 CFM with 40 HP, Baldor Super-E, 324T frame, 1.780 RPM motor. -- Enclosure dimensions: 133" long, 68" deep, 160" high. Filter weight is 7,300 lbs.

DONALDSON-TORIT - 376RFW-10 or 12 , ...Dust Collector: 45,000 CFM @ 9.7:1 Air-to-cloth ratio; 140" dia. round baghouse with: (376) filter bags of 10' length (oval bags provide for radial movement of bag during cleaning for longer life), total 4,632 sq. ft. filter area. -- Filtration media cleaning via a floor-mounted 7.5 HP medium pressure air pump (eliminates the need for compressed air which can be susceptible to condensation and freezing); 36" x 65" return air outlet and 48" x 48" inlet for dust laden air. -- Includes: Rotating cleaning air manifold driven by 0.33 HP motor; (1) NEMA-9 solenoid and diaphragm valve which rotates over the bag openings; walk-in plenum for bag access/maintenance. -- Galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride-up of bags once installed; walk-in access door at top of ladder. -- Equipped with: Structural steel support; maintenance platform; caged ladder; bolt-on involute arm; explosion doors (need to be replaced). -- Includes Backward inclined FAN EQUIPMENT: Size 7 BCS floor-mounted Fan set at 45,000 CFM @ 15" SP belt driven at 1,485 RPM; powered by a 200 HP TEFC Motor via OMRON/IDM E7 Series Inverter. -- 24" Rotary Air Lock at the bottom of the 60° hopper. -- Complete with: Pictured electrical controls are included. -- Note new 200 HP electrical motor was replaced recently. --. Unit had an accidental fire at bottom section near hopper causing the explosion doors to burst. Unit still working as they are not returning the air. Can be sold with of without replacement of doors. Cost of which is negotiable. -- Professional dismantling and rigging available at extra cost. Please call!