
704-841-2001
Backed with a massive machinery database considered to be “the blue book” of woodworking machinery), EX-FACTORY Auctions provides a complete assessment of your equipment and allows you to interact with the market real-time in our dynamic Online Auction!
1664 Results Found
704-841-2001
$15,625
Toyota 42-6FGCU25 Fork LiftReliable Toyota propane forklift available for immediate sale. The machine was utilized in a cabinet and millwork manufacturing facility and is well suited for warehouse, commercial, and industrial operations. The forklift starts, drives, lifts, and operates properly. Toyota forklifts are known for their durability, ease of maintenance, and strong resale value within the industry. -- 5,000 Lbs Cap., 2.2L 4-Cylinder engine, Load Center 24", Triple-stage mast, 189" raised height, 13,332 Hours -- Includes; automatic transmission, side shifter with 42" forks, LP gas and cushion tires. Approx.. weight 8,800 Lbs
Call for Price
TRAVAINI TRO 400S-1A 25 HP Liquid Ring Vacuum Pump: -- 25 HP, Liquid ring, single-stage vacuum pump. Nominal capacity 380 ACFM and max. Vacuum 28" HgV. -- Pump materials include cast iron housing, ductile iron impeller and stain less steel shaft. Shaft seals are carbon face with viton elastomers. -- 25 HP, 230/460 Volt, 3-Phase, 60 Hz, TEFC monoblock motor assembly for direct drive, no field alignment needed. -- Sealing fluid re-circulating system includes reservoir of carbon steel with fluid level gauge & drain, high efficiency discharge separator, and over-sized heat exchanger; high temperature switch to protect against over-temperature operation. -- Complete with charge of Dynalube fluid. -- Suction line accessories include: Inlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve, and vacuum relief valve. -- Heat exchanger is air cooler type made from aluminum and extended surface fins. -- Electrical controls include: Starter/overload reset, pump running light, hour meter, hi-temp light, terminal blocks mounted in a NEMA 12 cabinet.
TRAVAINI TRO 500S-1A 40 HP Liquid Ring Vacuum Pump, 13,920 Hours: -- Specifications:Nominal capacity 500 ACFM @ 20" HgV; max Vacuum 27" HgV. -- Pump materials include cast iron housing, ductile iron impeller and stain-less steel shaft. Shaft seals are carbon face with Viton elastomers. -- 40 HP, 440 V, 60 Cy, 3 Ph., TEFC monoblock assembly for direct drive, no field alignment needed. -- Sealing fluid re-circulating system includes reservoir of carbon steel with fluid level gauge and drain, high-efficiency discharge separator and oversized heat exchanger. -- High temp switch to protect against over temp operation.- Complete with a charge of Dynalube fluid. -- Suction line accessories include inlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve, and vacuum relief valve. -- Heat exchanger is air cooler type made from aluminum and extended surface fins. -- Electrical controls include: Starter/overload reset, pump running light, hour meter, hi-temp light, and terminal blocks, all mounted in a NEMA 12 cabinet.
Call for Price
AAF PULSE-PAK 21-3H Pulse-Jet Cartridge Dust Collector. (3H) is three-high filter elements. (21) is the total number of Panel Pak V's.The Panel Pak filter element has two flat panels of pleated media in a Vee-Configuration allowing installation and change-out with minimum time and effort. Each cartridge has its own gasket ensuring a positive, air tight seal. -- Consists of two modules: one containing (9) 3x3 filters and the second contains (12) 4x3 filter cartridges, for a total of (21) cartridges. -- Housing dimensions: 191.75" High (with 48" hopper clearance), 104.25" Wide, 94.25" Depth, and Weighs about 6,400 Lbs. -- Air consumption about 6 cubic feet/hr. at 90 PSI of clean dried air. -- Fan and Airlock available at extra cost. please inquire.
Call for Price
ACCU SYSTEM./PILLAR MACHINE MMTJ,...CNC Round End Tenoner/Mortiser/MiterCNC Round End Tenoner & Slot Mortiser. - 3-1/2" Max. part width, 1" max. thickness. -- Table with: (2) Working zones allowing machining of (2) parts at (1) time; right & left 45° fences with pneumatic holddowns. -- Industrial PC with: Multi-axis controller, 15" color touch-screen, unlimited program storage, and changing from program-to-program in seconds. -- All axes CNC controlled, Y- & Z-axis with rotary screw & nut; X-axis with rack & pinion. -- 6 HP Miter & Tenon spindle, 3 HP Mortise spindle. -- Seller states they have spend $10,000 to replace the linear bearings, hard drive and added a side pressure cylinder (now included on new machines) -- Toling included. -- Availability date to be provided. (As soon his new machine arrives).
ACCU-SYSTEMS - DD: Handheld Glue & Dowel InserterSpecifications -- Dowel diameter: 5 - 10 mm (0.20" - 0.39"); dowel length: 25 - 38 mm (0.98" - 1.50"). -- Currently setup for: 8 mm Dia. x 30 mm L (0.31" dia. x 1.18" L) Dowels.Equipped with: -- Microprocessor-controlled glue & dowel gun (for repetitive cycles) with: Dowel reject slide; insertion speed (60) dowels/Min.; weight 3-1/2 Lbs. -- (1,000) Dowel cap.; 9" dia. vibratory bowl feeder with: Bowl size: 9" Dia. x 4" H. -- 2-1/2 Gallon cap.; glue & water combination tank with: 8" Dia. x 12" H Tank size & single button glue flush system. -- Microprocessor control. -- (4) Casters.
Call for Price
ACCU-SYSTEMS - HPJ: CNC Bore, Glue & Dowel Inserter -- Specifications(2) Working zones: 24" Each; table length: 49"; CNC controlled head assembly with: Rapid (side-to-side) traverse.Head assembly with (1) Boring, gluing & dowel insertion unit: 2 HP - 3,500 RPM Drill motor; head currently setup for: 8 mm Dia. dowels.Max. dowel length: 1.57" (40 mm); Up to 1.125" (28.5 mm) material thickness with: Digital readout for height adjustment. -- Clamping System(4) Pneumatic, quick "side to side" adjustable hold-down clamps. -- Operator InterfaceNC "Color Touchscreen" Control; ALLIMAC "Advantech" for: Function & part programming and program storage; Windows based PC. Selector control for boring only or doweling; adjustable drilling speed. -- Complete with:(1) 18" Dia. vibratory feed hopper totally sealed electronically metered glue system with: 1-Button flushing; 100 PSI high power glue pump; 2-1/2-gal. glue tank.Anti-slip table surface; rack & pinion drive; centralized dust collection manifold. -- Actual model: ACCU-SYSTEMS HPJ-49NOTE: In 2023 the feed block assembly and part number J10361 was replaced. - See "Photos" link above. Once opened, the 10th "image" displays the "Purchase Order". Rails and bearings were replaced earlier.
Call for Price
ACCU-SYSTEMS - HPJ-7-96: CNC Bore, Glue, and Dowel Inserter -- Specifications(4) Working zones; table length of 104"; CNC controlled head assembly with: Rapid (side-to-side) traverse; assembly with: (1) Boring, gluing & insertion unit; 2 HP - 3,500 RPM drill motor; head currently set up for: 8 mm Dia. dowels.Max. dowel length: 1.562" (40 mm); up to 1.125" (28.5 mm) material thickness with: Digital readout for height adjustment. -- Clamping System(8) Pneumatic dual functioning (for horizontal & vertical drilling capability); hold-down clamps; function selector control for boring only or doweling; adjustable drilling speed. -- Operator InterfaceNC "Color Touchscreen" Control; ALLIMAC "Advantech" for: Function & part programming and program storage; Windows based PC. -- Complete with:(1) 18" Dia. vibratory feed hopper; totally sealed electronically metered glue system with: 1-Button flushing; 100 PSI high power glue pump; 2-1/2-gal. glue tank.Anti-slip table surface; rack & pinion drive; centralized dust collection manifold. -- Actual model - Accu-Systems HPJ-7-96
ACCURATE TECHNOLOGY Pro Kit Digital Measuring System (X & Y Axis)Vertical Panel Saw Kit, Horizontal axis, 40" range (mounts to left-most station only). -- Digital Readouts programmed to use offsets of +40, +80, +120 for stations 2, 3, and 4. -- Vertical axis, 82.7" measuring range. (same kit could probably be used for 76" machines); spans the entire range of vertical motion of the machine. Sometimes this mounts onto the right side of the beam, sometimes on the left (depends where you can find space for the installation). -- With this setup, the digital readout can:Measure bottom up from bottom fence, ANDMeasure bottom up from mid-fence (up to 3 flip outs can be used), ANDMeasure top-down with kerf compensationModel 290 scale offer excellent debris resistance (wood, plastic, and metal), plus high slew rates, and very low maintenance. The kits are typically supplied with our General-Purpose Readouts. These offer ability to measure from different references (such as bottom fence and flip-out, mid-fence on panel saws), plus kerf compensation abilities (for compensation during top-down cutting operations). -- Battery operation with CR123 Lithium Battery.
ACME ENGINEERING & MANUFACTURING - CENRI VENT QB24N: 5 HP Centrifugal Material Handling BlowerSpecifications -- Inlet dia.: 26.38". -- Outlet size: 19.24"; x 26";. -- Blower wheel size: 24"; Dia. x 7-1/2"; W.Equipped with: -- 5 HP - 1,745 RPM - 230/460 V Motor.
Call for Price
ACT 3-12 Cartridge Dust Collector Cartridge style downflow dust collector rated at 6,000 CFM @ 13". Heavy-duty with 7 and 10 gauge construction. Specifications: -- Blower, 15 HP rated at 6,000 CFM. @ 13" -- (12) Poly-Elite, spun-bond polyester media with 100 Sq. Ft. of media per filter filter (total 1,200 Sq. Ft.) that are 99.9% efficient. -- Reverse pulse filter cleaning system. -- 15HP All-in-one starter/disconnect/timer board/digital pressure gauge 460V 3ph -- DK-XP – explosion rated drum kit with quick-lock easy-access filter doors. -- 16" inletEquipped with: -- TCBI 15 HP Blower with direct drive, top mount. -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (6) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Includes: -- Silencer for TCBI 15. -- 15HP All-in-one starter/disconnect/timer board/digital pressure gauge 460V 3phOptional Return Air Includes: -- Shut off landing spot in control panel for explosion isolation valve. -- Explosion Vent installed with hardware, 24" x 36" explosion relief panel. 5.72 sq ft vent area. Domed for durability. KST value required. -- Sprinkler coupler for collectors with 1 module. -- Solenoid heater kit with 1 heat trace kit for cold weather installation. -- 14" VF - Explosion Isolation Valve Assembly (dirty air to dust collector), Must be installed between 14' and 55' from the dust collector inlet. If an elbow exists, minimum distance is 21'. -- Custom - Explosion Isolation Valve, 16" VF - Explosion Isolation Valve Assembly (clean air return to building). Must be installed between 24' and 55' from the dust collector outlet. -- 10 year workmanship and materials warranty -- Made in the USAPhoto does not represent the actual model
ACT 3-12 Cartridge Dust Collector Cartridge style down flow Dust Collector: Rated at 6,000 CFM @ 13".Heavy-Duty with: 7 & 10 Gauge construction. Specifications -- Blower. 15 HP Rated at: 6,000 CFM @ 13". -- (12) Poly-Elite, spunbond polyester media with: 100 Sq. ft. of: Media per filter (total: 1,200 sq. ft. 99.9% Efficient. -- Reverse Pulse Filter cleaning system. -- 15 HP All-in-one starter/disconnect/timer board/digital pressure gauge: 460 V - 3 PH. -- DK-XP Explosion rated Drum Kit with: Quick lock easy access filter doors. -- 16" Inlet.Equipped with: -- TCBI 15 HP Blower with: Direct drive; top mount. -- Automatic reverse jet cleaning via: Compressed air; (1) pulse valve per (2) cartridges for a total of (6) pulse valves; Goyen solenoids and diaphragm. -- Heavy-Duty steel legs; position unit approx. 4' above the ground; made with 7 & 10-gauge construction. Used from 2015 - 2023; Filters changed in 2019 Rigger will be needed to remove & load.
Call for Price
ACT 3-24 Cartridge Dust CollectorCartridge style downflow dust collector rated at 8,000 CFM. Heavy-duty with 7 and 10 gauge construction. Specifications: -- Blower, 25 HP rated at 8,000 CFM @ 12" -- (24) Poly-Elite, spun-bond polyester media with 100 Sq. Ft. of media per filter filter (total 2,400 Sq. Ft.) that are 99.9% efficient. -- Reverse pulse filter cleaning system. -- 25HP All-in-one starter/disconnect/timer board/digital pressure gauge 460V 3ph -- DK-XP – explosion rated drum kit with quick-lock easy-access filter doors. -- 18" inletEquipped with: -- TCBI 25 HP Blower with direct drive, top mount. -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (12) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Return Air Includes: -- Shut off landing spot in control panel for explosion isolation valve. -- Explosion Vent installed with hardware, 36" x 36" explosion relief panel. 8.63 Sq. Ft. vent area. Domed for durability. KST value required. -- Sprinkler coupler for collectors with 1 module. -- Solenoid heater kit with (2) heat trace kits for cold weather installation. -- 18" VF - Explosion Isolation Valve Assembly (dirty air to dust collector), Must be installed between 16' and 55' from the dust collector inlet. If an elbow exists, minimum distance is 24'. -- Custom - Explosion Isolation Valve, 20" VF - Explosion Isolation Valve Assembly (clean air return to building). Must be installed between 19' and 55' from the dust collector outlet. -- 10 year workmanship and materials warranty -- Made in the USAPhoto does not represent the actual model
Call for Price
ACT 3-6 Cartridge Dust Collector Cartridge style downward flow dust collector rated at 4,000 CFM. Specifications: -- Blower, 10 HP rated at 4,000 CFM @ 10" w.c. -- Holds (6) Nano Elite, merv 15, cartridge filters with up to 1,524 sq. ft. of filter media that are 99.9% efficient. -- Pulse control timer board with built-in digital pressure gauge. -- Drum lid with latch kit, quick-lock easy-access filter doors. -- Magnetic motor starter panel, 10HP All-in-one starter/disconnect/timer board/digital pressure gauge 460V 3ph -- (6) Filter Upgrade to ACT Nano-Elite, flame-retardant, Nano-Fiber media with industry best Merv 15 efficiencyEquipped with: -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (3) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. -- 12" in-let. -- Silencer for TCBI 10. -- (1) 55 Gallon drum. 10 year manufactures materials and craftsmanship warranty . Made in the USA
Call for Price
ACT 4-16 Cartridge Dust Collector Cartridge style downward flow dust collector rated at 8,000 CFM. Specifications: -- 20 HP Direct drive, top mounter blower rated at 8,000 CFM @ 10" w.c. -- (16) Nano Elite, flame-retardant, Nano-Fiber merv 15, cartridge filters with up to 4,064 sq. ft. of filter media that are 99.9% efficient. -- Pulse control timer board with built-in digital pressure gauge. -- Drum lid with latch kit, quick-lock easy-access filter doors. -- Magnetic motor starter.Equipped with: -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (8) pulse valves. Goyen diaphragm and solenoid valves -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Options: -- Fan outlet damper. -- Fan outlet silencer. Other models available, please check with the Product Manager10 year workmanship and materials warranty -- Made in the USA
Call for Price
ADVANCE LIFTS P-2536 Scissor LiftThe P-Series lifts are Advance Lifts most popular series as they fit a wide array of manufacturing applications.SPECIAL FEATURES & BENEFITS: -- These units are equipped with the patented “Platform Centering Devices";, which doubles or triples lift life. -- All of the controllers are Underwriter Laboratory listed assemblies. -- These units are fully primed and finished with a baked enamel finish. -- The cylinders are machine grade with clear plastic return lines. -- All pressure hoses are double wire braid with JIC fittings. -- The reservoirs are mild steel. -- These units conform to all applicable ANSI codes.Specifications: -- 2,500 Lbs. capacity. -- Platform size 36" x 72" (Min. Platform Size: 24" x 48" Max. Platform Size: 48" x 72") -- Max. End Load Capacity 2,500 Lbs. -- Max. Side Load Capacity: 2,500 Lbs. -- Base frame Size: 24"" x 48". -- Lowered Height: 6.5". -- Raised Height: 42.5". -- Approx. Speed Up: 27 Sec. -- Internal Motor: 2 HPWarranty 10 Year Structural / 250,000 Cycles - 1 Yr Parts and Labor
Call for Price
ADVANCE LIFTS P-4036 Scissor LiftThe P-Series lifts are Advance Lifts most popular series as they fit a wide array of manufacturing applications.SPECIAL FEATURES & BENEFITS: -- These units are equipped with the patented “Platform Centering Devices";, which doubles or triples lift life. -- All of the controllers are Underwriter Laboratory listed assemblies. -- These units are fully primed and finished with a baked enamel finish. -- The cylinders are machine grade with clear plastic return lines. -- All pressure hoses are double wire braid with JIC fittings. -- The reservoirs are mild steel. -- These units conform to all applicable ANSI codes.Specifications: -- 4,000 Lbs. capacity. -- Platform size 36" x 72" (Min. Platform Size: 24" x 48" Max. Platform Size: 48" x 72") -- Max. End Load Capacity 3,300 Lbs. -- Max. Side Load Capacity: 2,900 Lbs. -- Baseframe Size: 24"" x 48". -- Lowered Height: 6.5". -- Raised Height: 42.5". -- Approx. Speed Up: 27 sec. -- Internal Motor: 2 HPWarranty 10 Year Structural / 250,000 Cycles - 1 Yr Parts and Labor
Call for Price
ADVANCE LIFTS P-6036+M Scissor LiftThe P-Series lifts are Advance Lifts most popular series as they fit a wide array of manufacturing applications.SPECIAL FEATURES & BENEFITS: -- These units are equipped with the patented “Platform Centering Devices";, which doubles or triples lift life. -- All of the controllers are Underwriter Laboratory listed assemblies. -- These units are fully primed and finished with a baked enamel finish. -- The cylinders are machine grade with clear plastic return lines. -- All pressure hoses are double wire braid with JIC fittings. -- The reservoirs are mild steel. -- These units conform to all applicable ANSI codes.Specifications: -- 6,000 Lbs. capacity. -- Platform size 36" x 72" (Min. Platform Size: 24" x 48" Max. Platform Size: 48" x 72") -- Max. End Load Capacity 4,100 Lbs. -- Max. Side Load Capacity: 3,500 Lbs. -- Baseframe Size: 24"" x 48". -- Lowered Height: 6.5". -- Raised Height: 42.5". -- Approx. Speed Up: 27 sec. -- Internal Motor: 2 HPWarranty 10 Year Structural / 250,000 Cycles - 1 Yr Parts and Labor
$8,950
AEM - 502-37: Dul Head Wide Belt Sander2-Head; 36" width capacity; 0 - 5-1/2" thickness capacity with: Rubber-covered contact roll and adjustable finishing platen. 1st Head. Rubber-covered contact roll; 5-1/2" dia.; 25 HP motor. 2nd Head. 2-1/2" Wide finishing platen; 15 HP motor. -- 37" x 75" Abrasive belts; ACRO-TRACK electronic tracking; pneumatic belt tensioning; infeed & outfeed spring loaded rubber covered holddown rolls. -- 11-3/4" Min. part length without butt feeding; variable feed speed: 10 - 50 FPM; 0 - 8" opening with: Mechanical digital readout; (4) precision jacks. Includes: -- Safety perimeter emergency stop bar around entire machine; air caliper disc brakes on both sanding heads. -- (2) 6" Dia. dust outlets; 3,200 CFM required total; motor load meters; 22" infeed conveyor.
Call for Price
AES SIRIUS 950M ATC CNC MACHINING CENTER (FEED THRU): -- Specifications:Automatic CNC feed through Point to Point Boring Machine that combines flexibility and high productivity.A perfectly suited solution for small to midsize companies & artisans in need of an automatic solution for precision drilling with a low-cost investment.Parts can be discharged at the opposite end of the machine for automated material handling or returned to the Operator for manual unloading. -- Working Capacity:Max. panel size on X-Axis is unlimited; Y-axis is 37.4" (950 mm); Z-axis is 2-3/4" (70 mm).Min. panel on size X-axis is 9.84" (250 mm); Y-axis is 3.14" (80 mm); Z-axis is 0.31" (8 mm). -- Positioning Speed: Panel feeding speed of 229 FPM (70 MPM); Y-axis at 229 FPM (70 MPM); Z-axis at 65 FPM (20 MPM).Axes positioning by AC drives & brushless Servo motors; the Panel moves in X-axis & the boring head moves in Y & Z-axes. -- Work Area:NC Controlled "Optical Material Sensor" creates a zero-panel reference point by reading the panel ends; this ensures that RH & LH (mirror image) panels will always be symmetrical.High precision clamping automatically positions the workpiece. Automatic presser moves independently and adjusts to workpiece thickness. Pneumatic side pusher makes locating workpiece accurate and efficient. LH Side pressure clamp with automatic adjustment & pneumatic locking according to the panel width.Scratch resistant air floatation tables make for ease of loading and unloading from either side of the machine. -- Boring Unit:HSD Drilling head; 3 HP (2.2 kW), variable speed from 4,500 - 8,000 RPM motor. (10) Independent vertical spindles on 32 mm centers; (5) spindles in X-axis & (5) spindles in Y-axis.(6) Horizontal spindles with (2 + 2) in X-axis & (1 + 1) in Y-axis.(1) X-Axis grooving saw for max. 120 mm dia. blade; variable speed from 5,500 - 10,000 RPM. -- Machining:HSD 7 HP (5.5 kW) spindle; variable speed from 1,000 - 18,000 RPM with manual tool change system.(1) 6-Position ATC Automatic Tool Change system with ATC rotary magazine. -- Operator & Machine Control: PC Based user-friendly, icon-driven control housed on the main machine base; displays programming graphics, functions, and machine data. -- Complete with: Users & Maintenance Manuals; ALPHACAM "Essential" is provided with machine for ease of programming at the Controller. -- Software Disclaimer:EX-FACTORY INC. offers NO warranty or support, written or implied concerning any/all "optional" or "additional" manufacturer or 3rd party software supplied with this machine. All software related issues including re-licensing fees/requirements/functionality & training is ultimately the sole responsibility of the "Buyer".Actual Model is: AES SIRIUS 950M - ATC



















