EXTREMA ET-160 Fixed Spindle Shaper;"Extremely" Well-built and with solid features.Specifications: -- Solid spindle of 1-1/4" with 5-13/16" under the nut. -- Large 10 HP motor. -- (3) Spindle speeds of 5,500 - 7,500 & 10,000 RPM. -- Heavy cast iron table with a 12-3/8" max. table ring. -- Spindle lock, micro-adjustable back fence, and reversing switch. -- Miter gauge, cutterhead guard assembly, operator's manual, and tool kit.

EZ CAR CRUSHER MODEL A+ --Opening 20 ft long x 7'6" width x 8 ft height --System Pressure 2500 psi --Port Reliefs Set At 2650 psi --Cylinders 10" bore --Travel 78" --Shaft 4" rod --Remote --Approx 5,500 Hours

EZ CAR CRUSHER MODEL B With Remote --HydraulicsSystem Pressure 2500 psiPort Reliefs Set At 2650 psi --Cylinders 8" bore --Travel 72" --Shaft 2.5" rod --OpeningSize 20" x 7'6" x 7'7" --OverallWeight 49,000 lbsLength 43'5"Travel & Operating Height 13'3"

HOMAG AMBITION 2262 (KAL 210) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING); PRODUCTION EDGEBANDER): -- Specifications: Working Capacity: Coiled stock min./max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"); strip material min./max. Edge Thickness 0.4 - 6 mm (0.16 - 0.234").Panel stock min./max. thickness 12 - 40 mm (0.472" - 1.574"). Panel Overhang 30 mm (1.18"). -- Infeed Fence:Adjustable infeed fence with manual digital indicator positioning. -- Pre-milling Station:(2) 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with: Trimming column, (2) horizontal & cross-slides with spindle adjustment.Electro-pneumatic horizontal jump movement of the 1st motor; includes electronic frequency inverter for control of motor speed and braking.(2) Dust extraction hoods, air jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Preheater:Preheating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures.Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multipurpose Magazine:2-Coil magazine expands capability by running coiled material, strips, and solid wood bands. Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table allowing the Operator to center the panelon the edgeband. -- Premelting System: Overhead Premelting Unit -- Gluing System: EVA - Hot Melt.QA 34 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allow for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates.Lower melting unit equipped with: Automatic glue level control; melting capacity: 12 kG/h (26 Lbs/Hr). -- Pressure Section:Manual adjustment with digital counter: (1) Large 160 mm dia. driven & (6) 70 mm dia. idle rollers; pneumatic pressure control depending on edgebanding material used.WORKSTATIONS: -- End Trimming Unit:(2) 0.8 kW (1.0 HP) - 200 Hz, 12,000 RPM Motors to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Rough/Pre-trimming Unit:Top & bottom, (2) 0.55 kW (0.74 HP) - 12,000 RPM motors; height adjustment with the top pressure beam and tilting range +/- 1°. Manually adjusted with digital counters. -- Multifunction Profile/Bevel/Corner Rounding Unit:Multifunction (2) 0.4 kW (0.54 HP) - 12,000 RPM Motors to fine trim the edge overhangs at the workpiece upper & lower edge, as well as trimming around the front & rear vertical edge; Servo controlled.Max. feed speed 0f 20 MPM (65.6 FPM) when corner rounding. -- Profile/Bevel Scraping Unit:Top & bottom for thick PVC/ABS, pneumatically activated. -- Flat Glue Scraper Unit:Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit:Top & bottom edge buffing/polishing.

HOMAG KAL 210 AMBITION 2260 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Coiled stock min/max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max. thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor;Includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, an air-jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-Heater: the Pre-heater brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multi-Purpose Magazine: 2-Coil magazine expands capability by running coiled material & strips, magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates, lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 LBS/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 KW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & bottom Flush Trimming Unit: Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12: Multi-function 0.4 KW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10: Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11: Top & bottom edge buffing/polishing, pneumatically activated. -- Operator & Machine Control:HOMATIC PC 22 Power Control w/Touch Screen: Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating syst

HOMAG OPTIMAT KL-75 / A20 EDGEBANDER 0.4 - 20 mm (3/4") Thickness edgebanding cap., 70 mm min. panel thickness.Equipped with: Automatic edge feed magazine for coil, HPL & strip stock; "Hot Melt" glue system with QA34 Quickmelt unit, with reversible glue roll applicator; pneumatically controlled pressure roll section with 7 pressure rollers. -- Workstations: Double motor front & rear end trim, straight & chamfer trimming (0.5 HP - 10,400 RPM ea. motor). -- Top & Bottom rough trims (2 HP - 11,500 RPM ea. motor). -- Top & Bottom fine trims, tiltable 0° - 30° (0.5 HP - 10,980 RPM ea. motor); open space for workstation. -- Adjustable top and bottom glue scraper. -- Electronic Height adjustment for Top pressure beam with double V-belts, 80 mm wide Heavy Duty feed chain w/rubber pads. -- Feed speed variable up to 35 MPM. -- Complete with: SIKO Digital adjustments on T & B Flush and Fine Trim. -- Homatic NC21 Controller, Fixed position Outrigger panel support, insulated sound cabins w/interior and overhead lighting for all trim workstations. -- Includes Owners Manual and the Electrical Schematics.NOTE: Suggested replacement parts needed, as noted by our technician - all the track pads, the hold-down belt, the pressure roller, and likely a glue pot rebuild. Estimated cost for these parts, not including labor is $5600. The replacement of these parts is NOT included in the machine price.

HOMAG AMBITION 2274 (KAL 370/6/A3) EDGEBANDER (W/PRE-MILL): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.3 - 3 mm (0.011. - 0.118"), Strip material min/max Edge Thickness 0.4 - 1 mm (0.016 - 0.039"),Panel stock min/max thickness 8 - 60 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18").Minimum workpiece width: 2.36" (60 mm) with workpiece thickness ≤ 22 mm) & 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units:Top/Bottom spraying device prior to workpiece pre-milling. Designed for applying a separating agent, for easier cleaning of any residual glue on the panel. -- In-Feed Fence: Pre-heated manually adjustable in-feed fence with digital indicators. -- Pre-Milling Station:(2) 2.2 HP (3.0 kW) - 150 Hz, 9,000 RPM vertical jointing spindle motors; equipped with panel blow-off device and SIKO digital counters for adjustments. -- Panel Pre-Heat Unit: Quartz lamp for heating substrate edge before glue application. -- Edge Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Maximum roll diameter: 400 mm & 830 mm.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System Homag Quickmelt: QA 3 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast five-minute (5) heat-up time. -- Pressure Section: Programmable (Servo), automatic pressure zone adjustment, (1) large 150 mm dia. driven & (4) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Workstations: -- End Trimming Unit:(2) 1 HP (0.8 kW) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. Programmable (Servo). -- Rough/Pre-Trimming Unit:(2) 0.55 kW 0.74 HP (0.55 kW) - 12,000 RPM Motors, tilting range +/- 1° & counter-rotating to machine feed to prevent blowout & .Height adjustment synchronized with the top pressure-beam .With digital counters. -- Scraping Unit:Top & bottom for thick PVC/ABS, electro-pneumatic positioning & pneumatically activated. Pneumatically-controlled blow off nozzles. Height adjustment synchronized with top pressure beam. -- Flat Glue Scraper Unit:Top & bottom to remove potential glue squeeze-out, electro-pneumatic positioning in and out of the processing area & electro-pneumatically activated height adjustment synchronized with top pressure beam. -- Buffing Unit:Top & bottom edge buffing/polishing. Operator & Machine Control: -- Power Touch Control Multi-Touch Screen C

HOMAG AMBITION 2274 (KAL 370/6/A3) EDGEBANDER (W/PRE-MILL/HIGH PRODUCTION) (aka "TAPE ROCKET"): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.3 - 3 mm (0.012. - 0.125"), Strip material min/max Edge Thickness 0.4 - 1 mm (0.016 - 0.039"),Panel stock min/max thickness 8 - 60 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). Minimum Work piece length 610 mm(24").Minimum workpiece width: 2.36" (60 mm) with workpiece thickness ≤ 22 mm) & 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units:Top/Bottom spraying device prior to workpiece pre-milling. Designed for applying a separating agent, for easier cleaning of any residual glue on the panel. -- In-Feed Fence: Pre-heated manually adjustable in-feed fence with digital indicators. -- Pre-Milling Station:(2) 2.2 HP (3.0 kW) - 150 Hz, 9,000 RPM vertical jointing spindle motors; equipped with panel blow-off device and SIKO digital counters for adjustments. -- Panel Pre-Heat Unit: Quartz lamp for heating substrate edge before glue application. -- Edge Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Maximum roll diameter: 400 mm & 830 mm.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System Homag Quickmelt GA 65 / QA 65: QA 65 - EVA Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast five-minute heat-up time. -- Pressure Section: Programmable (Servo), automatic pressure zone adjustment, (1) large 150 mm dia. driven & (4) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Workstations: -- End Trimming Unit PK 25:(2) 1 HP (0.8 kW) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. Programmable (Servo). -- Fine Trimming Unit PF20:(2) 0.54 HP ( 0.4 kW) - 12,000 RPM, fine trimming unit for edge overhangs at the work-piece upper & lower edge.Operator Interface: -- Power Touch Control Multi-Touch Screen Controller on separate console with 21.5" Full HD flat screen display, keyboard and mouse. Functions in Windows environment, includes fault diagnostic, OS9 real-time operating system."WoodScout", included graphic diagnostic tool designed to increase throughput and decrease down time. Graphical PLC diagnosis display of the error location in the machineCustomer-specific data base system that allows the operator to enter the reason for the error as well as the corrective measures to assist with future tro

HOMAG KAL 310/4/A3/S2 Edgebander (w/Pre-Milling): -- Specifications:Working Capacity: 0.3 - 3 mm Edge thickness cap., min. panel width 22 mm; max. panel thickness 60 mm; Dual speed -- Equipped with: Pre-Milling Unit 3481: (2) motors, 3 kW, 9000 RPM each, pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator in-feed fence. -- Hot Melt Glue System "QA 34" Quick-Melt Unit: with heated glue roller; -- Edge Magazine Unit 2456: Automatic (2) coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers, (1) large dia. driven & (2) idle rollers; with pneumatic pressure control for straight edges -- HOMATIC "NC 21" Power Control System: Controller operates in Windows-XP environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem. -- Workstations:End Trimming Unit: (2) motors, 0.18 kW - 12,000 RPM each, to cut excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit 3201: Top & bottom trim station, 0.55 kW - 12,000 RPM +/- 1° angle adjustment, manual positioning with digital counters. -- Fine/Bevel Trim Unit 3216: (2) motors 0.4kW - 12,000 RPM each, manual positioning with digital counters -- Profile Edge Scraping Unit: with electro-pneumatic adjustment -- Buffing Unit 4402: Top and bottom with oscillation. (2) motors, 0.25kW, 2850 RPM -- Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAL 310/4/A3/S2Note: This machine has a new display and a new back up one as well!

HOMAG AMBITION 2240 PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"),Panel stock min/max thickness 12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18") -- In-feed Fence:Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station:Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor.includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, air jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-HeaterPre-heating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures.Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multi-Purpose Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System: (EVA - Hot Melt)QA 3 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr) -- Pressure Section:Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Work Stations End Trimming Unit HL 81:0.8 kW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & Bottom Flush Trimming Unit:Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12:Multi-function 0.4 kW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10:Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit:Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11:Top & bottom edge buffing/polishing, pneumatically activated.Operator Interface: HOMATIC PC 22 Power Control w/Touch Screen:Controller functions in Windows

HOMAG EDGETEQ 4.5 SERVO QUICK MELT EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Specifications:RH Feed (Brandt) Configuration; 0.4 - 3 mm (0.016 - 0.125") Coil Cap.; 0.4 - 8 mm (0.016 - 0.315") edge strip cap.; 8 - 60 mm (0.32" - 2.4") panel thickness; 160 mm (6.3") min. panel length; 70 mm (2.76") min. panel width.Equipped with: Pre-Milling Station, (2) motors @ 2.25 kW (3.0 HP), 12.000 RPM, (1) clockwise & (1) counter-clockwise rotation for chip-free and clean panel edges.Equipped with diamond cutter heads. -- In-feed Fence, with servo motor positioning. -- Infrared Radiant Quartz Heating Unit between glue roller and pressure section. -- Automatic Edge Magazine, for strip & coil stock, strips 0.4 mm - 8 mm (0.016 - 0.315"), coils up to 3 mm PVC and "HD" guillotine. -- "Quick Change" Glue Unit for maintenance & glue purging/color change. -- Pressure Section, 1st. roller driven plus (2) idle rollers, timed pneumatic pressure controlled; Motorized positioning of the Pressure Zone. -- Feed Speed, variable 8 - 14 MPM. (26 - 46 FPM), 14 MPM (46 FPM) when contour trimming. -- HOMAG "Power Touch Control, Full HD wide screen multi-touch display, keyboard, mouse, Industrial PC.PLC control according to IEC 61131 standards, USB connection at the operating panel; Ethernet connection 10/100 MBIT RJ45Work Stations: Straight/Chamfer End Trimming: - (2) Motor @ 0.35 kW (1/2 HP) 12,000 RPM, automatic indexing for straight to bevel trimming from control panel. -- Multi-Stage Fine Trimming Unit MS 40: - Top/bottom (2) motors, 0.55 kW (0.75 HP) 12,000 RPM, equipped with (2) Multi-Profile Radius cutter heads, each with (4) Carbide insert knives. (4) Profile options, Profile1, Profile2, Bevel & Flush trimming, via the program control. Includes Auto tilt feature, servo controlled to edge thickness, Nesting top copy system. -- Multi-Function Contour Trimming/Corner Rounding Unit MF-50: (2) Motor 0.4 kW (1/2 HP) 12,000 RPM, dual purpose for CR & continuous Top & Bottom edge trimming trimming with servo motor control of the cutter.2-Position automatic indexing for 1-mil, 2-mil & 3-mil thickness. For leading & trailing edges vertical corner rounding of panels; equipped with radius cutters, HSK 25 system; 3 mm max. edge thickness. -- Scraping, Multi-Stage Profile Scraping Unit MZ 40: Top/bottom with Multi-Profile for (2) Radii. 1 mm & 2 mm or 3 mm instead of 2 mm, servo control positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Finish Scraping Unit: - Flush top/bottom on panel surface with floating insert knives. -- Buffing Unit: - Top/bottom (2) motors, 0.10 kW (0.125 HP) 2,800 RPM. Complete with:Motorized, programmable Top hold-down pressure beam; padded sound enclosure, isolation transformer for multiple input voltages, used tooling and Original Factory machine documentation. -- Actual Model is HOMAG EDGETEQ 4.5 SERVO QUICK MELT.NOTE: Pictured Return Conveyor is NOT INCLUDED

Houfek Buldog 7-3M-1100-RRC 3 Head wide belt sander43" width cap, Roller / Roller / Combination-headHead Configuration1st Head – Rubber – 90 shore @ 200mm (7.9";) dia.2nd Head – Rubber - 90° shore @ 2000mm (7.9";) dia.3rd Head– Rubber - 45° shore @ 200mm (7.9";) dia. with adjustable platen.Specifications -- Sanding width 1100 mm 43" -- Work piece height 3-160 mm 0.118"~6.3" -- Sand belt size 1120 x 2620 mm 44" x 103" -- Conveyor feed speed 3~15 m/min 9.8~49 FPM -- Table motor 0.18 kW 1/4 HP Equipped with & Features -- Main motor 1st head 18 kW 24HP -- Motor 2nd head 15 kW 20HP -- Motor 3rd head 15 kW 20HP -- Voltage 460/3/60 -- Exhaust outlet (4) 180mm; (1) 100mm (4) 7"; (1) 4" -- CFM requirements 6700 m3/hr 3950 CFM -- Weight 3100 kg (approx) 6820 lbs -- Floor space 3885x1715x2260mm153"x68"x89"

HURST 600 HP Waste Fired Boiler; -- Specifications:Complete in-place system with the following features: -- Decommissioned July 2019. -- 150 PSI. (300 PSI max wp), -- 20,700 Lbs per hour. -- Fuel House, Boiler Building and all Controls -- System has been "pickled" to maintain tube integrity.

HUSTLER - FC-2, ...ScreenSpecifications: -- OD at the longest point: 104" -- Long at longest point: 122" -- Tall at the tallest point: 65"Equipped with: -- (2) Shutoff switches

HUSTLER - 48", ...Inclined Infeed Cleated ConveyorThis Conveyor is "New, Never Used," and stored outside. Specifications: -- Width: 48 In. -- Horizontal load area: 8 Ft. -- Inclined height: 21-1/2 Ft. -- Total length: 31-2/3 Ft. -- Main motor: 5 HPEquipped with: -- Oiler -- Cleated

HYDREX HPX510-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 19,500 Lbs).

HYDREX HPX510-5 Hot Press 120 Tons with (5) Daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x 10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; Rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 kW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 kW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs. -- Overall dimensions: 3,800 length (+610mm -boiler + 610mm -pump/tank) x 1,790 wide x 2,450 mm high.

HYDREX HPX48-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 4' x 8', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (6) Cylinders (upstroke) -- 80 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 98" x 51" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (6) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 80 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4 KW (5.5 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 12,500 Lbs). Overall dimensions 129" x 65" x 102" high.Also available with (3) openings - 100 Tons and (5) openings - 100 Tons.

HYDREX HPX410-5 Hot Press 160 Tons using (8) hydraulic cylinders, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to nominal 4' x 10' (about 51" x 126"). -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 160 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- Platen size 1300 mm x 3200 mm (51" x 126") approx. Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 40 PSI specific pressure over the entire platen area; 54 kW heating power. Approx. 7.5 kW (10 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position; Heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 27.500 Lbs. -- Optional: Extra Large Oil Heating Tank for Special Higher Temperatures if needed.

IMA ADVANTAGE 500 L EDGEBANDER (w/PREMILL & CORNER ROUNDING): -- Specifications:Edgebanding capacity: Coiled material: 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped with:Pre-milling Unit: 4 kW x 2 (5.3 HP x 2) - 9,000 RPM Vertical joining spindles; SIKO digital readouts, and particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit: Dual motor, (2) 0.66 kW (0.88 HP) motors; suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit: Top & Bottom flush trimming, W 1.0 kW x 2 (1.34 HP x 2) - 12,000 RPM Ea. motor; against the feed (up milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit: Multiuse; Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W - 12,000 RPM. -- Profile Scraper Unit: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all holddown beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is I M A ADVANTAGE 500 L