Mereen Johnson 431 DC

These two rip saws were removed from service in working condition some time ago. The seller purchased them and never installed them. They have been in storage the whole time.

The seller has confirmed that this Mereen Johnson 441 Rip saw is in great working/running cnodition and it is ready to load! - 2004 Cameron Auto Opti-Rip Infeed - Model: 34F-M1 - Serial: OR164 - 100% Servo (only Servo is this Cameron) - Full amp load 81 - 44" W bed - Up to 20 saws can be run on the arbor - No moving blades BUT there are moving lasers Although this one has been pulled from service, they have an identical one still running and available for inspection....

Mereen Johnson 424 Gang Rip Saw

Mereen-Johnson Model 441-DC Gang Rip Saw Capacity: Arbor space 41” Arbor Drive: 75 HP 3600 RPM TEFC motor Feed Drive: HP TEFC variable speed direct; 45’ to 225’ feet per minute Hold Downs & Bed Plate: Four 5” dia. Air loaded high yield idle press rolls Saw Sleeve: One 41” capacity sleeve Dust Collection: Four upper dust pick-ups: two (2) 8” dia., two(2) 4” dia., one lower 4”dia. Pick-up:(requires total 4820 CFM @ 5,000 feet per minute) Swing Arm & Tip-Up Cart: One floor mounted dual shaft swing arm and one tip-up saw sleeve set-up cart Electrical: Arranged for 3 phase, 60 cycle, 460V Cameron Automated Opti-Rip Model #34F-M1 System: Manufacture Year: (2004) Complete with length measurement Tally System 5 infeed belt and chains for feeding a Gang Rip saw up to 41” wide 16 width sensors 3 sets of pinch rolls for short stock 1 fixed & 4 movable laser lights This system feed for 4’ to 16’ max lumber length It feeds from operator right to left Wired 220V; If 440V required, a transformer will be needed

225 KVA 480 volt to 208Y/120

Specification from owner 5 Foot Wide - Midwest Automation top and bottom high pressure laminating line capable of laminating up to 5’ x 12’ panels consisting of the following equipment: Powered infeed roller conveyor PC-160 panel cleaner with top and bottom nylon brushes and dust collection shrouds. GS-417 top and bottom glue spreader with 65” panel width capacity, glue rolls are in excellent condition, separate top and bottom direct drive motors, powered opening, glue pump system. PP-500 panel positioning station for panels up to 62”W x 148”L x 1.63”T. RP-3170 heated roller press with 67”W high temperature silicone covered top and bottom rolls. SL-510 scissor lift table, 5’ x 10’ roller platform and 6000 lb. capacity. Includes 2 new recoated glue rollers and manuals. All equipment is 575V, 3PH. May consider selling pieces separately.

Midwest 5033-16 Countertop Saw Only (1) router installed

Mighty Mite Sawmill mounted on Trailer 86 Hours on the system 150 HP Perkins Diesel Engine Slab drop and take away 58" Chipper with 24" Infeed Belt Outfeed Conveyor Scissor lift for stacking lumber

Miner 4” Edger

Mixer Direct 304SS Tanks These were installed in a building that has been sold. Except for one tank that was used once, the rest were never put into production. Includes: - (3) 10,000 gal tanks - (3) 15,000 gal tanks with agitators - (2) 1,000 gal high shear mixing tanks with dual motors - (1) Holding tank with agitation (I think this is a 2,000 gal tank with agitator, but I have not gotten up there to look at the tag.

16” capacity 5 hp motor 220 volt 3-phase

Montgomery 100 HP Hammer Mill Includes: Outfeed conveyor and Infeed Hopper

In good condition. Has 50” opening. No drive motor but would take 100-200HP depending on material being run. No screen included. Very heavy weighs approximately 4 ton.

Moon's Band Saw Sharpener

Mobark Rosserhead Debarker Model 636 Currently in use

Canadian Morbark Sawmill PLUS Electric Vertical Gang Edger Keyknife Headrig Slabber 42" opening 4 knee carriage (4) new Headrig blades 60" Modern Set Works New tires

This mill has been shut down. The debarker is complete and ready to be removed. Morbark 636 Debarker Infeed/Outfeed Log Conveyors Waste conveyor runs under the system Approx 7' high structure Separate conveyors to load chips to trailer Includes All electric and hydraulic, steel walkways, 6x6 insulated cab

This machine was purchased new. The seller has changed contracts and no longer needs the system for their application. 2019 Morbidelli P200 5 X 12 Contour Edgebander Eye M Controller with 21.5? Touch Screen Hand Held Pendant w/ 7? Touch Screen Air Conditioned Cabinet 20.5 HP Liquid Cooled Router Tool Touch Probe 12 Position Ride Along Tool Changer 14 Position Side Tool Changer 17 Vertical Spindles 8 Horizontal Spindles / 3+3 in X and 2+2 in Y Hinge Unit Edgebanding Unit Standard two Coils Magazines on Safety Enclosure Additional Support for 6 Coils EVA or PUR Glue Aggregates for 3mm PVC Flexmatic Table with 8 Rails 8 Lifting Rails Variety of Vacuum Pods HE Pods Conveyor for Dust Busch Mink Vacuum Pump Pro Speed w/ Safety Enclosure

X5 Author cnc router 11KW/15HP 5 axis electrospindle router motor Spindle takes HSK63 tool holders 120” x 51.2” working area Max speed in X/Y/Z – 131/131-/74 FPM Remote pendant 18 spindle boring unit with 12 vertical (7+5) and six horizontal (2+2, 1+1) 12 position rear tool changer Centralized dust collection See less