--MAKE AN OFFER!--VERY GOOD CONDITION-- BRANDT KDF 650 (1650 HIGHFLEX) Edgebander, with 3,339 Hrs. (As of 10/31/23), Pre-Mill & Corner Rounding Specifications: 0.4 - 12 mm (1/2") Edge cap., panel thickness 5/16" - 2-3/16", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with top pressure beam for all work stations, equipped with digital height indicator. "PC-16" Program Control with: 21-1/2” Display, signal infeed light to ensure proper spacing between panels. Equipped with: Pre-milling station for cleaning edges of the panel; "Quick change" glue tank for maintenance & glue color change. 32” Dia. Coil table. Automatic magazine for strip & coil stock, 3 mm PVC guillotine, (1) drive plus (3) idle roll "pneumatically controlled" pressure sections with digital indicator for quick edge thickness changeover. Workstations: End trim (0.33 HP - 12,000 RPM motors), chamfers 0° - 15°; Top & bottom flush/bevel/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motors) with insert knives for 2 mm PVC radius. Vertical copy wheels are servo-controlled for quick changeover, programmable from the control panel. 2-Motor (4 corners) contour trim for profile corner rounding (two 0.5 HP - 12,000 RPM motors), with insert knives for 2 mm PVC radius. Top & bottom scraping for 2 - 6 mm radius, pneumatically controlled blowoff nozzles; Top & bottom buffing (0.25 HP - 1,400 RPM motors). End trim, flush/bevel/radius trim & corner rounding stations have HF motors with electronic brakes; feed chain track speed 42 FPM, 2 HP feed drive. Complete with: Operator control panel, PLC (Programmable Logic Control) keypad, and LED readouts; used tooling. NOTE: Actual Model "KDF 650". NOTE: Specifications must be confirmed. Machine Dimensions: 254” x 50” x 68” H. Machine Dimensions with Outboard Panel Support Extended: 254” x 66” x 68” H. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

--make offer--requires repair-- BRANDT KDF 440 C/AMBITION 1440 FC EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) & 3,359 Hrs. Specifications: Edge & Workpiece Capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") Panel thickness, 160 mm (6.30") Min. panel length, 70 mm (2.76") Min. panel width. Equipped with: Adjustable Infeed Fence: Motorized adjustment with 0.049 kW (0.07 HP) Motor. Joint Trimming/Pre-Milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, Left-Hand & Right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting, 0.4 - 8 mm (0.016" - 0.31") Strip thickness, 3 mm (0.12") PVC Max. coil thickness. Hot Melt Glue Application Unit: 6 - 10 kg/Hr. (13 - 22 Lbs./Hr.) Melting capacity (Depending on glue type). Workpiece Preheating Unit Pressure Zone: (1) Driven & (2) Idle Rollers, Timed pneumatic pressure controlled, Servo motor positioning for programmable edge thickness changeover. Feed Speeds: 8 - 14 MPM (27 - 45 FPM), 11 MPM (36 FPM) with Contour trimming. BRANDT "POWERTOUCH" Control: With 21" HD LCD Touchscreen monitor. Workstations: Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors, with 0° - 15° Automatic chamfer, Pneumatic adjustment & Activation/deactivation of edging material overhang using "POWERTOUCH" control. Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt, with Horizontal & Vertical Tracing wheels, Brushless multi-axis servo motors for positioning of work-unit & horizontal copy wheels for quick changeover, with (3) Positioning options: Profile 1, Profile 2 & Flush trimming. Multi-Functional Trimming Unit: (2) 0.4 kW (1/2 HP) 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Either radius or chamfer cutters can be mounted, 3 mm (0.12") Max. edge thickness. Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"), Servo control positioning of vertical & horizontal copy wheels, PVC Scrape collection box, Pneumatic adjustment using "POWERTOUCH" control, Pneumatic disengagement. Top & Bottom Glue Scraping Unit: Flush on panel surface, with Floating insert knives. Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) 2,750 RPM Motors. Complete with: Motorized, programmable hold-down pressure beam with 0.12 kW (0.16 HP) Motor, 1.5 kW (2 HP) Feed motor, 32" Diameter Coil table, Padded sound enclosure. NOTE: CPU needs to be replaced. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

--make offer--excellent condition-- BRANDT OPTIMAT KTD 820 Contour Edgebander Specifications: Designed for straight, curved (contour), or beveled edgebanding. Edgebanding thickness 0.4 - 3 mm (0.02” - 0.12”). Coil cutoff 0.4 - 3 mm (0.02” - 0.12”) (Max. edge height 45 mm/1.77”). Panel thickness 16 - 40 mm (0.63” - 1.57”). Min. radius 25 mm (0.98”). Min. panel length 180 mm (7.09”), Min. panel width 100 mm (3.94”). Feed speeds 0.7 - 4.2 MPM (2.30 - 13.80 FPM). Equipped with: 33” Dia. Vertical coil table. Small glue pot for quick heat-up. Magazine for coil or solid strips. Guillotine. Handheld gluing unit, with Tool balancer & Rotating jib with 8’ Travel. (2) 23-1/2” x 27-1/2” x 35 H Work tables. Large panels can be glued by guiding handheld gluing unit around panel mounted to vacuum suction table. Small panels can be glued by guiding panel along gluing unit mounted to table. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

BRANDT - KDN 540 2C: EdgebanderSpecifications 0.4 - 8 mm Edge cap.; panel thickness 5/16" - 1-5/8"; min. panel length 160 mm (6-3/8"); 65 mm (2-1/2") min. width.Line Control (NO limit switches) for workstation function. Automatic height adjustment with: Top pressure beam for all workstations; equipped with: Digital height indicator. -- PC-16 Program Control with: 7-1/2" VGA Screen; 8 MB IDE flash disk; 8 MB RAM; Internal Modem for: Remote diagnostic link; signal infeed light: Ensures proper spacing between panels.Equipped with: Quick heat up Glue System (approx. 12 Min) w/glue tank for maintenance & glue color change. Glue temperature indicator for both the glue pot & glue roller with: LED Thermostat; automatic temperature reduction if the machine is idle for 15 Min or more. -- Glue Applicator Roller: Reversible & retractable from the fence line. -- Automatic magazine for strip & coil: Large coil table 800 mm dia. to accommodate large coils of 3 mm PVC stock; 3 mm PVC guillotine; (1) drive plus (2) split secondary rollers "pneumatically controlled" pressure sections. WorkstationsEnd trim: 1/4 HP - 12,000 RPM Motors; chamfers 0° - 15° via programmable controller. -- Top & Bottom flush/radius trim: Bevels 0° - 15°; 1/2 HP - 12,000 RPM motor with: Insert knives for 3 mm PVC radius. -- 2-Motor Corner Rounding unit for: Leading & trailing edges of panels; either radius or chamfer cutters can be mounted, 1/2 HP - 12,000 RPM motors; 3 mm Max. edge thickness. -- Top & Bottom scraping for: 3 mm Radius, pneumatically controlled indexing system. -- Top & Bottom Buffing (last station): 1/4 HP - 2,800 Motors. -- End Trim & Flush Trim Stations: High Frequency motors w/electronic brakes; feed chain track speed: 36 FPM - 3 HP feed drive.Complete with: Operator Control Panel w/PLC (Programmable BRAND push-button Controls) keypad & LED readouts.Includes: (1) Bag DELTA Dust Collector and various banding material.

BRANDT KDF-350 C Edgebander with PRE-MILL & CORNER ROUNDING: Specifications: 0.4 - 3 mm (0.125"), panel thickness 8 mm (0.31") - 55 mm (2.1"), min. panel length 160 mm (6 - 0.37") and 65 mm (2 - 0.5") min. width; PLC line control (no limit switches) for workstation function.Infeed & Equipped with: -- Pressure beam height adjustment for all work stations via digital height indicator. -- Features: Signal infeed light to insure proper spacing between panels and a panel edge pre-heating system. -- Equipped with: (2) Motor Pre-milling (3 HP- 12,00 RPM); -- Hotmelt granulate glue application system with approx. 10 Min heat up time; automatic reduction of glue temperature when idle more than 5 Min. -- Automatic magazine for strip & coil (large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections. -- "See-through" sound & safety enclosure. -- Operator control panel w/PLC (Programmable Logic Control), keypad & 7-0.5" screenEdgebanding Workstations: -- End trim (0.33 HP - 12,000 RPM motor ea.), chamfers 0° - 15°, program controlled from straight to bevel. -- Top & bottom flush/bevel/radius trim, bevels 0° - 15° (0.5 HP - 12,000 RPM motor ea.), with insert knives for 3 mm PVC radius. -- 1-Motor corner rounding unit for top & bottom corners (0.5 HP - 12,000 RPM motor). -- Top & bottom scraping for 2 - 6 mm radius, pneumatically controlled blowoff nozzles and program controlled indexing. -- Last Station: Top & bottom buffing (0.9 kW (1.21 HP - 2,710 RPM - 230/400 V Motors).Features & Feed: -- End trim, flush trim and corner round stations have HF motors w/electronic brakes; 200 Hz Electronic frequency inverter. -- Feed chain track speed 36 FPM with 2 HP feed drive; workpiece support track extends up to 19-0.5".NOTE: Machine does not power on.

BRANDT - Ambition 1440 AT (KDF-440 AT): Edgebander (w/Premill & Corner Rounding) + "AirTec" PUR/EVA Gluing Technology -- Specifications Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness; 8 - 60 mm (0.31" - 2.36") panel thickness; 160 mm (6.30") min. panel length; 70 mm (2.76") min. panel width.Equipped with: -- Heated Adjustable Infeed Fence. Radiant Heated with: Manual adjustment. -- Joint Trimming/Premilling Station. (2) 2.2 kW (3 HP) - 12,000 RPM Motors; left-hand & right-hand rotation with: Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device. 3 mm x 45 mm (0.12" x 1.77") Or 1 mm x 55 mm (0.04" x 2.17") max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- "AirTec" PUR Glue Application. For preglued PUR banding. -- Hot Melt Glue Application Unit. 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone. (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds. 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touchscreen Monitor.Workstations -- Front & Rear End Trimming Unit. (2) 0.18 kW (1/4 HP) - 12,000 RPM Motors with: 0° - 15° Automatic chamfer; pneumatic adjustment; activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit. (2) 0.55 kW (3/4 HP) - 12,000 RPM Motors; 0° - 25° automatic tilt with: Horizontal & vertical tracing wheels; brushless multiaccess Servo motors for positioning of work unit; horizontal copy wheels for Quick changeover with: (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit. (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for top & bottom, leading & trailing edges, and corner rounding of panels.Servo Motors for: Positioning of work unit & horizontal copy wheels.Either radius or chamfer cutters can be mounted: 3 mm (0.12") Max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit. (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08").Servo Control positioning of: Vertical & horizontal copy wheels.PVC Scrape collection box, pneumatic adjustment using: "POWERTOUCH" Control, pneumatic disengagement. -- Top & Bottom Flat Glue Scrapping Unit. To remove excess before Buffing. -- Top & Bottom Buffing Unit. (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle holddown rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model: BRANDT - AMBITION 1440 AT (KDF 440 AT).

BRANDT - KDN 210: Edgebander0.4 - 3 mm (1/8") Edge thickness cap.; 8 - 50 mm (0.3" - 2") panel thickness; 60 mm (2.3") min. panel width; 140 mm (5-1/2") min. length.Equipped with: -- Hot Melt granulate glue system with: "Quick Melt" start up (10 - 12 Min heat up) with: Reversible rotation glue applicator roller & automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min to reactivate). -- Includes: Automatic feed magazine; coil stock feeds automatically with guillotine cutoff; all strip stock fed automatically through strip feed magazine. -- 3-Roller pressure section: 1st Driven; next (2) idle) with: Electronically controlled & feed speed synchronized drive roll.Workstations -- Vertical travel double motor front & rear end trim with: Tilting of 0°- 15° cap. (0.24 HP - 12,000 RPM motors). -- Top & bottom flush/bevel trimmers (0.36 HP - 12,000 RPM motors); bevel 0° to 15°. -- Feed speed: 30 FPM. Features -- Operator control panel at: Eye-level. -- Automatic height adjustment with: Top pressure beam for all workstations. -- Digital height indicator on holddown beam. -- Electronic motor brakes on trimmers.

0.4 - 3 mm (1/8") Edge thickness cap., automatic coil & strip feed magazine, guillotine for 3 mm PVC banding, fast startup (12 Min heat up) glue system; reversible rotation glue applicator roller. -- Workstations: Vertical travel double motor front & rear end trim, 0.25 HP - 12,000 RPM motors. -- Top & bottom flush/bevel trimmers, bevel 0° to 15°, 0.35 HP - 12,000 RPM motors; top & bottom PVC scraping unit for up to 3 mm radius; top & bottom buffing unit, 0.15 HP - 2,750 RPM ea. motor. -- Feed speed 30 FPM; digital height indicator on holddown beam. -- Equipped with: Operator control panel at eye-level, electronic line control (no limit switches), electronic motor brakes on trimmers, 200 Hz electronic frequency inverter; used tooling & sound enclosure w/window.

BRANDT - FP 10: Corner Rounding Unit -- SpecificationsFreestanding unit for: Profiling, shaping, chamfering, or rounding most common type & shape of corner/edge on an edgebanded panel. -- Capacity: 55 mm (2-1/8") Max. panel thickness; 90 x 140 mm min. panel size; 3 mm max. edge thickness (depending on radius & edge material).Plunge in & plunge out points for tooling are: Programmable on Operator Control Panel with digital readout. -- Automatically scans profile with: SPS control; handles 90° & 180° symmetric profiles; tracing wheel & shoe follow exact shape contour of edgeband of corner. -- Equipped with: 3/4 HP - 27,000 RPM Motor; pneumatic clamping cylinder; optional 1/4 HP table mounted Buffing Wheel; electro-pneumatic operation with foot pedal control.

BRANDT - KDN 770-2C: EdgebanderSpecifications -- Hot Melt granulate quick heat up glue system; overhead glue tank for easy maintenance & glue color change. -- Automatic magazine for strip & coil: Large 800 mm dia. coil table to accommodate large coils of 3 mm PVC stock; 3 mm PVC guillotine. -- (1) Drive plus: (3) Idle rolls "pneumatically controlled" pressure sections. -- End Trimming: 0.33 HP - 12,000 RPM Motors; chamfers 0° - 15°. -- Flush Trimming. Top & bottom bevels 0° - 15° with: (4) Revolver type index presets; (2) 1/2 HP - 12,000 RPM motors; cutterheads with insert knives.Features -- Fine/Radius Trimming. Top & Bottom; bevels 0° - 15° with: (4) Revolver-type index presets; 1/2 HP - 12,000 RPM motors; cutterheads with: Insert knives for 3 mm PVC radius. -- 2-Motor corner rounding. -- Scraping Unit. Top & Bottom for: 2 - 6 mm Radius; pneumatically controlled blowoff nozzles. -- Buffing Unit: Top & bottom buffing; 1/4 HP - 1,400 RPM motors. -- Variable feed chain track speed from: 8 - 20 MPM (26 - 65 FPM); 2 HP feed drive.NOTE: Description based on: Model Type, manufacturer's plate, and information from Seller. Please inspect to confirm the required specifications. Dimensions & weight data are based on 3rd party information and could be incorrect; please verify & confirm if accurate dimensions & weight are required.

BRANDT - KDF-550 C, ...Edgebander with Premill & Corner RoundingEdge & workpiece capacity. Edge: 0.4 - 8 mm (0.016 - 0.31"); panel thickness: 8 -60 mm (0.31" - 2-3/8"); min. panel length: 60 mm (6.29"); min. panel width: 70 mm (2-3/4").Equipped with: -- Premilling Station with: Diamond cutterheads; (2) motors @ 2.25 kW (3.0 HP) - 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip free & clean panel edges. -- Infeed fence with: Servo motor positioning. -- Automatic Edge Magazine. For strip & coil stock; strips: 0.4 mm - 8 mm (0.016" - 0.31"); coils up to 3 mm PVC and "HD" guillotine. -- Pressure Section. 1st Roller driven; plus (3) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed: Variable; 8 - 14 MPM (26 - 46 FPM); 11 MPM (36 FPM) when using contour trimming. -- BRANDT "PowerControl PC 16"; memory: 256 MB RAM; 1 GB Flash Card Drive; Operator control panel with: 22" Color HD wide screen; soft keypad; internal modem for remote diagnostic link.Workstations -- End Trimming; (2) Motors @ 0.35 kW (1/2 HP) 12,000 RPM; automatic chamfer from the control panel: 0°- 15°. -- Flush/Bevel-Fine/Radius Trimming Unit: Top/bottom (2) motors; 0.55 kW (3/4 HP) 12,000 RPM; auto tilt positioning 0° - 25°; combination flush/radius/chamfer cutterheads; horizontal and vertical tracing wheels. -- Includes: (3) Positioning options: Profile 1, profile 2, and flush trimming. -- Corner Rounding Unit: (1) Motor; 0.35 kW (1/2 HP) - 12,000 RPM for leading & trailing edges; vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, Multi-Profile (PVC) Top/Bottom with (2) profiles: 1 mm & 2 mm or 3 mm Instead of 2 mm; Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box. -- Scraping Glue Unit: Flush top/bottom on the panel surface with floating insert knives. -- Buffing Unit: Top/bottom (2) motors; 0.10 kW (0.125 HP) - 2,800 RPM.Complete with: Motorized, programmable holddown pressure beam; padded sound enclosure. -- Actual Model: BRANDT, OPTIMATKDF 550 C

BRANDT PROFILINE KDF 970 2C HD EDGEBANDER WITH PRE MILL & CORNER ROUNDINGSpecifications: -- Edgebanding thickness 0.4 - 20 mm (0.02" - 0.79"), Including 3 mm (0.12") PVC banding. -- Panel thickness 8 - 60 mm (0.31" - 2.38"), Min. panel width 65 mm (2.56"), Min. panel length 160 mm (6.30"). -- Variable feed speeds 36 - 65 FPM (11 - 20 MPM), Max. feed speed using corner rounding units or applying solid wood 52 FPM (16 MPM). -- Working height 900 mm (35.43").Equipped with: -- Pre-milling unit, with (2) 3 kW (4 HP) - 11,580 RPM Vertical milling/jointing heads with FS Whisper Heads, Electro-pneumatic jump control, Head counter-rotation, & SIKO digital units for vertical & horizontal adjustments. -- 32-1/2" Dia. Coil table. -- Motorized infeed fence. -- Extended magazine for strips & coiled material. -- Reinforced guillotine for coiled edgebanding material, 0.4 - 3.5 mm (0.2" - 0.14") Thickness & 8 - 55 mm (0.31" - 2.17") Height. -- "Quick-Melt" Hot melt glue unit, with Heat-up time: Approx. 12 min., Pre-melt hopper feed, Quick-change hopper & tank for color changes, Reversible glue applicator roller rotation, Retractable glue roller, Infrared heating unit positioned between glue roller & pressure section to improve edge quality, and Pneumatic positioning & Locking. -- Programmable pressure section, with (1) Large driven & (4) Small pneumatically-controlled idler rolls and SIKO Digital units for adjustments. "POWER CONTROL PC 20+" Control, with 600 MHz, 256 MB RAM, USB Port, 1 GB Flash card, Internal modem for remote diagnostic access link, & 12" TFT Flat screen monitor. -- Line control (no limit switches) for workstation functions. -- Heavy-duty feed chain, with 2.2 kW (3 HP) Motor, Rubber pads, & Automatic chain track lubrication. -- Motorized top pressure beam with 0.14 HP (0.10 kW) Motor. -- Outboard panel support, with Roller guide & 1,000 mm (39.37") Adjustment. -- Sound enclosure.Workstations: -- Front & rear end trim unit, with (2) 1 HP - 12,000 RPM High frequency motors, 0° - 15° Chamfer, & Programmable pneumatic control for straight or chamfer trimming. -- Top & bottom rough trim unit, with (1) 1.86 kW (2-1/2 HP) High frequency motor. -- Top & bottom fine trim unit, with (2) 0.55 kW (3/4 HP) - 11,300 RPM High frequency motors with Electronic brakes, Servo control bevel, 0° - 25° Tilt, Vertical & Horizontal tracing, Servo control (in/out), & DFC Radius cutters. -- Corner rounding unit, with (2) 0.35 kW (1/2 HP) - 10,940 RPM High frequency motors, & Automatic 2-position edge thickness. -- Quick-change top & bottom profile scraping unit for rigid PVC edges, with Digital quick-set system for 2 - 6 mm (0.08" to 0.24") Radius, Pneumatic indexing, Servo control (in/out), & Pneumatically-controlled blow-off nozzle. -- Top & bottom buffing unit, with (2) 0.3 HP - 2,800 RPM Motors and Vertical & Horizontal tilt.Full Servo Edgebander, with Pre-Mill, Corner Rounding, Pre-Melt, $5,000 Package of Almost New Diamond Pre-Mill Heads, New

CAM-WOOD IAT 620-150HX INVERTER DRIVEN FINGER JOINT SYSTEM Lay-Up and Block-Staging Infeed Conveyor: -- 24" Wide x 31.5" long belt conveyor powered with 1/2 HP motors. The conveyor is controlled by the operating and system. Feeds at a constant rate of 180 FPM. Block delivery is controlled by the operator and machine system criteria to feed the Shaper. The conveyor facilitates keeping the system full and productive. FSR-62I Right Hand Inverter Type Finger Joint Shaper: -- Feed table is 24" wide and accepts blocks from 6" to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor and is equipped with provisions for vertical adjustment of 20 mm up and 20 mm down. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4"; maximum shaper cutterhead diameter - without knives. -- 5 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP - 2,850 RPM Scoring saw, accepts 7" dia. x 50 tooth x 5 mm blades. -- Conveyor powered by 1/2 HP motor. -- Table movement is inverter driven; powered by a 3 HP inverter motor with cycle speeds from 1 to 4 cycles per minute. Motor senses load and varies travel as needed. TC-62 Single Table Transfer Conveyor to the 2nd (Left Hand) Shaper: -- 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeds at a constant rate of 180 FPM. FSL-62I Left Hand Inverter Type Finger Joint Shaper with Glue Extruder: -- Feed table is 24" wide and accepts blocks from 6" to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4" Maximum shaper cutterhead diameter - without knives. -- 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP motor powers a top and a 2nd 2 HP motor powers a bottom scoring saw, both running at 2,850 RPM; accepts 7" dia. x 50 tooth x 5 mm blades. -- Conveyer powered by 1/2 HP motor. Table movement is Inverter driven; powered by a 3 HP + 3 HP inverter motor with cycle speeds from 1 to 4 cycles/Min. Motor senses load and vary travel as needed. Speed is controlled by system criteria. Injection Type Glue Applicator: -- Extrudes adhesive into the fingers without a messy runoff. 6" Comb height is standard. Finger pitch 4 mm, 10 - 12 mm finger length is standard equipment (special sizes available as optional equipment) STC-62A Single Table Conveyor Belt to the Assembly Section: -- 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeding at a constant rate of 180 FPM. FJ-500A (240") Assembly Press with Cut-Off Saw: -- Capacity from 1" to 6"; wide x 1/2" to 3" high x and from 6' to 16-1/2' long. motor powers the upper and lower pre-assembly driven by (2) 2 HP motor . -- 5 HP infeed inverter drive. In-feed speed from 30 to 230 FPM. Speed is controlled by system criteria. -- 5 HP - 2,850 RPM Cutoff saw accepts 14" dia. x 120 tooth x 4 mm kerf blade. Cutoff Saw c

CAM-WOOD HIAT-620-205 WITH 3"; HIGH X 8"; WIDE X 20’ LONG WORKING CAPACITIESTECHNICAL SPECIFICATIONS:Incoming Block Requirements: --Incoming block lengths from 6'' to 39"; (optionnal 122") --Blocks must be at least 50% longer than their width. --Block thickness from 1/2"; to 3 1/2" --Block width from 1"; to 8" - --Assembled lengths from 10’ to 20’ - 24’ Optional --For use with PVAC adhesives --Works equally well with soft & hardwoods. --Moisture content preferred from 8% to 12% --Blocks should be surfaced (4) sides to ± 0.2 mm with 90° right-angle corners. To be supplied by the customer: --Electric power supply to electrical cabinet --Constant voltage with deviations of 5% or less --Temperature range for computer control should not exceed 95°F. --Maximum humidity for computer control system under 65% --Hydraulic oil --Skilled operating and maintenance personnel --Motor Control Center with under-voltage and overload protection; includes UL and CSA approved electrical components. Electric parts only, not the complete machine. --Total electricity demand: 63.75 KW, 85 HP --30 HP Compressor with a 50-to-60-gallon Air Receiver PRODUCTION CAPACITIES:Shaper Capacity: --Shift = 480 minutes --Finger length to buyer’s requirement --As an example: 1-1/2"; X 5/1/2"; X 24"; average finished block size at the Shapers --Shaper max. speed of (3) table strokes per minute --Table cycles will change as block widths become “wider"; or “taller"; at the Shapers --Table accepts up to (16) blocks when vertical finger jointing 1-1/2"; X 5/1/2"; example blocks. --Table accepts up to (4) blocks when horizontal finger jointing 5-1/2"; x 1-1/2"; example blocks.Press Capacity: --Assembly Press w/2 operators: -- (4) Table loads per min. x 20’ lengths x 480 min. per shift x 0.8 rate of utilization = 30,720 lineal feet per shift OR 36,864 lineal feet per shift with 24’ Press)Production Calculations: --VERTICAL Finger Jointing w/2 operators: -- Capacity of the shaper when finger jointing 1-1/2"; x 5-1/2"; x 2’ long blocks: (3) tables stroke per minute X 16-blocks per table load X 2’ average infeed block length x 480 minutes per shift X 0.8 rate of utilization = 36,864 lineal feet per shift (63.34 M³) --HORIZONTAL Finger Jointing w/2 operators: -- Capacity of the shaper when finger jointing 5-1/2"; x 1-1/2"; x 2’ long blocks: (3) table strokes per minute X 4 blocks per table load x 2’ average infeed block length x 480 minutes per shift X 0.8 rate of utilization = 9,216 lineal feet per shift (19.46 M³) NOTE: Capacity is maximum as shown at Assembly Section and is dependent on blocks thru the Shapers System consists of

CAM-WOOD IAT 620-150H INVERTER DRIVEN FINGER JOINT SYSTEM 3" X 6":Lay-Up and Block-Staging Infeed Conveyor: -- 24" Wide x 31.5" long belt conveyor powered with 1/2 HP motors. Conveyor is controlled by the operating and system. Feeds at a constant rate of 180 FPM. Block delivery is controlled by the operator and machine system criteria to feed the Shaper. The conveyor facilitates keeping the system full and productive. FSR-62I Right Hand Inverter Type Finger Joint Shaper: -- Feed table is 24" wide and accepts blocks from 6" wide x up to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor and is equipped with provisions for vertical adjustment of 20 mm up and 20 mm down. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4"; maximum shaper cutterhead diameter - without knives. 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP - 2,850 RPM Scoring saw, accepts 7" dia. x 50 tooth x 5 mm blades. Table movement is Inverter driven; powered by a 3 HP + 3 HP inverter motor with cycle speeds from 1 to 4 cycles/Min. Motor senses load and varies travel speed as needed. Speed is also controlled by system criteria STC-62A Single Table Transfer Conveyor to the 2nd (Left Hand) Shaper: -- 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeds at a constant rate of 180 FPM. FSL-62I Left Hand Inverter Type Finger Joint Shaper with Glue Extruder: -- Feed table is 24" wide and accepts blocks from 6" up to 31.5" long x 5/8" to 6" wide. Shaper spindle is driven by a 20 HP motor. Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4" maximum shaper cutterhead diameter - without knives. 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP motor powers a top and a 2nd 2 HP motor powers a bottom scoring saw, both running at 2,850 RPM; accepts 7" dia. x 50 tooth x 5 mm blades. Conveyer powered by 1/2 HP motor. Table movement is Inverter driven; powered by a 3 HP + 3 HP inverter motor with cycle speeds from 1 to 4 cycles/Min. Motor senses load and varies travel speed as needed. Speed is also controlled by system criteria Injection Type Glue Applicator: -- Extrudes adhesive into the fingers without the messy runoff associated with glue rollers. 6" Comb height is standard. Finger pitch 4 mm, 10 - 12 mm finger length is standard equipment (special sizes available as optional equipment) STC-62A Single Table Conveyor Belt to the Assembly Section: -- 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeding at a constant rate of 180 FPM. FJ-500A (198") Assembly Press with Cut-Off Saw: -- Capacity from 1" to 6"; wide x 1/2" to 3" high x and from 6' to 16-1/2' long. A 2 HP motor powers the upper and a 2nd 2 HP motor powers lower pre-assembly/crowder rolls. With 5 HP infeed inverter drive. In-feed speed from 30 to 230 FPM. Speed is controlled by system criteria. 5 HP - 2,85

CAM-WOOD FSM-460AX Finger Joint ShaperSingle Finger joint Shaper with 8" min. and unlimited max. block length; 4" max. block thickness, maximum timber height to feed into assembly press is 3"; 18" max. block width (horizontal joint only); 18" table working width.Equipped with: -- Shaper spindle powered by 10 HP belt drive motor with 50 mm dia. spindle turning at 5,500 RPM; 160 mm (6.3") max. dia. cutter. -- Trim-saw powered by 5 HP direct drive motor at 2,850 RPM and a 1" dia. saw spindle; swings 180 mm (7") max. blade dia. -- Table cycles 2 to 4 per Min via the hydraulic system with a 2 HP hydraulic power unit. Includes 5" dia. dust outlet.Features: -- Manual Fingerjointer performs end trimming and shaping functions on right and left end of blocks. -- Air-operated clamp holding blocks firmly in place. After the workpiece is clamped, the table feeds past the saw and shaper spindles to perform trimming and finger-joint operations; trim saw cuts blocks exactly 90° ends. -- Shaper spindle is precision-constructed for cutting fingers accurately; swings up to 6" dia. tooling. -- Spindle height adjustment is displayed on the dial readout for easy adjustment. -- Table travels on a precision linear guide for stability; table traverse driven by hydraulic power system smooth and accurate block feeding. -- Variable feed speed permits proper feed for hard or soft wood. -- Cast iron frame and table for durability.

CAM-WOOD MODEL FSG-150X Manual FINGER JOINT GLUE APPLICATOR -- Manual operation of sliding table ; Specification: -- Glue roller type -- Working width 24" maximum -- Working thickness 6" -- Glue roller drive 1/2 HP with reducer -- Standard clus height 4"

CAM-WOOD TYPE F1, MODEL FAH 8" X 30’ HORIZONTAL FULLY AUTOMATIC FINGER JOINT SYSTEM - SINGLE CHAIN TYPEMECHANICAL SPECIFICATIONS FOR THE FEED SYSTEM: -- Operating speed: 120 to 150 lugs/Min -- Intermittent feed motor: 2 HP + 1:25 -- Feed chain motor: 30 HP (20 kW) Servo Drive (C2) MECHANICAL SPECIFICATIONS: RIGHT-SIDE SHAPER: -- Cutterhead Motor: 25 HP -- Spindle size: 2-3/4"; (70 mm) -- Maximum cutter head body diameter: 10"; -- Cutterhead speed: 5,500 RPM at 60 Hz -- Trim Saw Motor: 15 HP -- Trim Saw blade size: 12"; (305mm) x 80 Tooth x 5mm kerf -- Cut-off saw Speed: 4,300 RPM -- Scoring saw motor: 3 HP -- Scoring saw blade: 7"; (180mm) x 50 Tooth x 5mm -- Scoring saw spindle speed: 4,200 RPM -- Holddown rise and lower motor: 1/2 HP (C3) MECHANICAL SPECIFICATIONS: LEFT-SIDE SHAPER: -- Cutterhead Motor: 25 HP -- Spindle size: 2-3/4"; (70 mm) -- Maximum cutter head body diameter: 10"; -- Cutterhead speed: 5,500 RPM at 60Hz -- Trim Saw Motor: 15 HP -- Trim Saw blade size: 12"; (305 mm) x 80 Tooth x 5 mm kerf -- Cut-off saw Speed: 4,300 RPM -- Scoring saw motor: 3HP -- Scoring saw blade: 7"; (180 mm) x 50 Tooth x 5 mm -- Scoring saw spindle speed: 4,200 RPM -- Holddown rise and lower motor: 1/2 HP -- Glue Application by GLUE COMB -- Standard glue height: 6"; High, 3.8 mm pitch 3.8 mm. Finger lengths from 10 to 12 mm (Other lengths available) (K) MECHANICAL SPECIFICATIONS: SHAPER OUT-FEED: -- Speed: 230 FPM -- Feed Motor: (1) 3 HP -- Vacuum device blower with 3"; Vacuum port: 5 HP (G) MECHANICAL SPECIFICATIONS: PRE-JOINT ASSEMBLY: --Feed chain drive: (2) 3 HP motors --In-feed Inverter: (1) 7-1/2 HP --Chain type: Flat top double chain --Feeding speeds from 30 to 300 FPM (H) MECHANICAL SPECIFICATIONS: 30’ (9.3M) ASSEMBLY PRESS: --Working dimension: 1"; to 8"; wide x 0.60"; to 2 3/8"; high x up to 30’ long --Upper & lower roll power: (2) 2 HP motors --In-feed Inverter: 7-1/2 HP --In-feed speed: 30 to 300 FPM --PROGRAMMABLE Cut-off saw power: 5 HP --Cut-off Blade dimensions: 14"; Dia. x 120 Tooth x 1"; bore --Cut-off saw speed: 2,850 RPM --Hydraulic power: 5 HP (With high speed oil tank) --Cycle Speed: 1 to 8 Cy/MinPRODUCTION CAPACITY - PARAMETERS: -- Based on a 480-minute shift -- Finger length to customer’s specifications -- Average infeed length at the shaper section is 20"; --A verage block cross section is 2"; x 4"; -- Chain speed at the Shaper sections is 150 lugs/Min -- Press capacity is (8) 30’ loads per minute (maximum) CAPACITY OF THE SHAPERS WHEN FINGER JOINTING 2"; X 4"; x 20" BLOCKS -- (120) Blocks per minute -- x 20"; Average infeed length -- x 480 Minutes per shift -- x 0.8 Rate of utilization = 76,800 lineal feet per shift CAPACITY OF THE PRESS ASSEMBLING 30’ LENGTHS: -- (8) Assembled lengths per minute -- x 20’ Per minute -- x 480 Minutes per shift -- x 0.8 Rate of utilization = 66,440 lineal feet per shift -- NOTE: If using the cutoff saw for multi-section pressin

CAM-WOOD TYPE F1, MODEL FAH 8" X 40’ AUTOMATIC HORIZONTAL FINGER JOINT SYSTEM - SINGLE CHAIN TYPE (including Feeding System from Optimizing Saw)Technical Specifications: -- Working thickness: 17 mm to 60 mm (.66" to 2 3/8") -- Working width: 25 mm to 205 mm ( 1" to 8") -- Maximum finish length: 12 Meters ( 40') -- Glue type: PVAC -- Timber moisture: 8% to 12% -- Infeed quality must be S4S with tolerance +/- 02 mm, wood need 90° right angle and straight MECHANICAL SPECIFICATIONS FOR THE FEED SYSTEM: -- Operating speed: 120 to 180 lugs/Min -- Intermittent feed motor: 2 HP + 1:25 -- Feed chain motor: 30 HP (20 kW) Servo Drive (C2) MECHANICAL SPECIFICATIONS: RIGHT-SIDE SHAPER: -- Cutterhead Motor: 25 HP -- Spindle size: 2-3/4"; (70 mm) -- Maximum cutter head body diameter: 10"; -- Cutterhead speed: 5,500 RPM at 60 Hz -- Trim Saw Motor: 15 HP -- Trim Saw blade size: 12"; (305 mm) x 80 Tooth x 5 mm kerf -- Cut-off saw Speed: 4,300 RPM -- Scoring saw motor: 3 HP -- Scoring saw blade: 7"; (180 mm) x 50 Tooth x 5 mm -- Scoring saw spindle speed: 4,200 RPM -- Holddown rise and lower motor: 1/2 HP (C3) MECHANICAL SPECIFICATIONS: LEFT-SIDE SHAPER: -- Cutterhead Motor: 25 HP -- Spindle size: 2-3/4"; (70 mm) -- Maximum cutter head body diameter: 10"; -- Cutterhead speed: 5,500 RPM at 60 Hz -- Trim Saw Motor: 15 HP -- Trim Saw blade size: 12"; (305 mm) x 80 Tooth x 5 mm kerf -- Cut-off saw Speed: 4,300 RPM -- Scoring saw motor: 3 HP -- Scoring saw blade: 7"; (180 mm) x 50 Tooth x 5 mm -- Scoring saw spindle speed: 4,200 RPM -- Holddown rise and lower motor: 1/2 HP -- Glue Application by GLUE COMB -- Standard glue height: 6"; High, 3.8 mm pitch 3.8 mm. Finger lengths from 10 to 12 mm (Other lengths available) (K) MECHANICAL SPECIFICATIONS: SHAPER OUT-FEED: -- Working size: Length 150 mm to 900 mm ( 6" to 35-7/16"); Width 25 to 205 mm (1" to 8") -- Speed: 70 m/Min ( 230 FPM) -- Infeed inverter : (1) 3 HP -- Vacuum device blower with 3"; Vacuum port: 5 HP (G) MECHANICAL SPECIFICATIONS: PRE-JOINT ASSEMBLY: -- Working size: Thickness 17 mm to 60 mm (5/8" to 2,3/8"); Width 25 mm to 205 mm (1" to 8") --Feed chain drive: (2) 3 HP motors --In-feed Inverter: (1) 7-1/2 HP --Chain type: Flat top double chain --Feeding speeds from 10 to 90 m/Min (32 to 292 FPM) (H) MECHANICAL SPECIFICATIONS: 40’ (12 M) ASSEMBLY PRESS: --Working dimension: 3/4"; to 8"; wide x 0.60"; to 2-3/8"; high x up to 40’ long --Upper & lower roll power: (2) 2 HP motors --In-feed Inverter: 7-1/2 HP --In-feed speed: 10 m to 70 m/Min (32 to 227 FPM) --PROGRAMMABLE Cut-off saw power: 5 HP --Cut-off Blade dimensions: 14"; Dia. x 120 Tooth x 1"; bore --Cut-off saw speed: 2,850 RPM --Hydraulic power: 5 HP (With high-speed oil tank) --Cycle Speed: 1 to 6 Cy/MinPRODUCTION CAPACITY - PARAMETERS: -- Based on a 480-minute shift -- Finger length to customer’s specifications -- Average infeed length at the shaper section is 500 mm (20";) --Average block cross-

CAM-WOOD TYPE F1, MODEL FAH 8" X 20’ AUTOMATIC HORIZONTAL FINGER JOINT SYSTEM - SINGLE CHAIN TYPE (including Feeding System from Optimizing saw)Technical Specifications: -- Working thickness: 17 mm to 60 mm (0.66" to 2-3/8") -- Working width: 25 mm to 205 mm ( 1" to 8") -- Maximum finish length: 6.2 Meters ( 20') -- Glue type: PVAC -- Timber moisture: 8% to 12% -- Infeed quality must be S4S with tolerance +/- 02 mm, wood need 90° right angle and straight MECHANICAL SPECIFICATIONS FOR THE FEED SYSTEM: -- Operating speed: 120 to 180 lugs/Min -- Intermittent feed motor: 2 HP + 1:25 -- Feed chain motor: 30 HP (20 kW) Servo Drive (C2) MECHANICAL SPECIFICATIONS: RIGHT-SIDE SHAPER: -- Cutterhead Motor: 25 HP -- Spindle size: 2-3/4"; (70 mm) -- Maximum cutter head body diameter: 10"; -- Cutterhead speed: 5,500 RPM at 60 Hz -- Trim Saw Motor: 15 HP -- Trim Saw blade size: 12"; (305 mm) x 80 Tooth x 5 mm kerf -- Cut-off saw Speed: 4,300 RPM -- Scoring saw motor: 3 HP -- Scoring saw blade: 7"; (180 mm) x 50 Tooth x 5 mm -- Scoring saw spindle speed: 4,200 RPM -- Holddown rise and lower motor: 1/2 HP (C3) MECHANICAL SPECIFICATIONS: LEFT-SIDE SHAPER: -- Cutterhead Motor: 25 HP -- Spindle size: 2-3/4"; (70 mm) -- Maximum cutter head body diameter: 10"; -- Cutterhead speed: 5,500 RPM at 60 Hz -- Trim Saw Motor: 15 HP -- Trim Saw blade size: 12"; (305 mm) x 80 Tooth x 5 mm kerf -- Cut-off saw Speed: 4,300 RPM -- Scoring saw motor: 3 HP -- Scoring saw blade: 7"; (180 mm) x 50 Tooth x 5 mm -- Scoring saw spindle speed: 4,200 RPM -- Holddown rise and lower motor: 1/2 HP -- Glue Application by GLUE COMB -- Standard glue height: 6"; High, 3.8 mm pitch 3.8 mm. Finger lengths from 10 to 12 mm (Other lengths available) (K) MECHANICAL SPECIFICATIONS: SHAPER OUT-FEED: -- Working size: Length 150 mm to 900 mm ( 6" to 35-7/16"); Width 25 to 205 mm (1" to 8") -- Speed: 70 m/Min ( 230 FPM) -- Infeed inverter : (1) 3 HP -- Vacuum device blower with 3"; Vacuum port: 5 HP (G) MECHANICAL SPECIFICATIONS: PRE-JOINT ASSEMBLY: -- Working size: Thickness 17 mm to 60 mm (5/8" to 2,3/8"); Width 25 mm to 205 mm (1" to 8") --Feed chain drive: (2) 3 HP motors --In-feed Inverter: (1) 7-1/2 HP --Chain type: Flat top double chain --Feeding speeds from 10 to 90 m/Min (32 to 292 FPM) (H) MECHANICAL SPECIFICATIONS: 20’ (6.2 M) ASSEMBLY PRESS: --Working dimension: 3/4"; to 8"; wide x 0.60"; to 2-3/8"; high x up to 20’ long --Upper & lower roll power: (2) 2 HP motors --In-feed Inverter: 7-1/2 HP --In-feed speed: 10 m to 70 m/Min (32 to 227 FPM) --PROGRAMMABLE Cut-off saw power: 5 HP --Cut-off Blade dimensions: 14"; Dia. x 120 Tooth x 1"; bore --Cut-off saw speed: 2,850 RPM --Hydraulic power: 5 HP (With high-speed oil tank) --Cycle Speed: 1 to 6 Cy/MinPRODUCTION CAPACITY - PARAMETERS: -- Based on a 480-minute shift -- Finger length to customer’s specifications -- Average infeed length at the shaper section is 500 mm (20";) --Average block cros