Custom-Built DEIMCO Through Feed Sprayer with a BLASDEL IR Preheat Tunnel that is available MARCH of 2023. Until then, the System can be seen in operation. -- Line was designed to preheat Fiber Cement board prior to painting and is followed by a Single-Arm Reciprocating Sprayer with 4-Spray Gun cap. Spray Guns not included.SEE ATTACHED VIDEO FOR A GOOD LOOK AT THE LINE's OPERATION!Built in 2019, the System was used for approx. (2) years; current owner changed their process and no longer requires the equipment.Oven width cap.: 60" Wide, 1-3/4" part height cap.; overall Oven dimension: 84" Wide x 12-1/2' long x 55" high, excluding the Blower & Stack. Line/Conveyor: Variable speed drive, 18.5 FPM to 26 FPM; Reciprocator operates up to 260 FPM and set by the HMI. 2-Zone Oven: -- Zone 1: (2) Upper left side wall/ceiling mounted; 18" x 60" emitters. -- Zone 2: (2) Right upper side wall/ceiling mounted 18" x 60" emitters; 8" clearance between emitters & rolls. Heaters: Natural gas using 7" WC; 480 Volt preheat; TC, FM, flange frame. - Gas Ratings: 360,000 BTUH Max. input ; 100,000 BTUH standby input; Air Exhaust on infeed & Injection Blower on outfeed. Electrical ratings: 26.6 Amps, 480 V - 3 Phase, 60 Hz.Exhaust: 980 CFM, 1 HP Motor.Control Panel: 60 AMP Disconnect switch, ALLEN-BRADLEY "Panel View Plus HM", IEC contactor & High Temp PID exhaust.NOTE: (25) New replacement conveyor rollers & (40) reconditioned rollers for IR Tunnel.DIEMCO Sprayer complete with: (1) Reciprocating Arm holds (4) guns and reads the leading & trailing edge to turn on & off the guns as the parts feed through; best to run full width loads through Sprayer; Overspray funnels into buckets.Spray Guns turn on & off based on the part leading & trailing edge; read by a light curtain on the infeed end.Dims: GFS Spray Cabin: 13' Deep x 8-1/2' wide x 9' high surround the reciprocating arm. - Filter & Exhaust Section: 13' Wide x 3' Deep x 10' High.

DEIMCO MFM-98 ACRYLIC COATING FINISHING SYSTEM: Drying Oven for the purpose of baking and drying the acrylic finish onto lumber and panel products. -- Specifications:3"; dia. x 21.625" long Rollers on 12"; centers; Infeed: 16' long In-feed Conveyor, 10' long Transfer Conveyor, 12' long Oven Conveyor: -- Operator & Machine Control:Built with Allen Bradley/Honeywell Components, MFM Serial: 1177, Voltage: 460V/60 Hz/25 Amp, Air: 1"; NPT 90PSIG. -- Complete With:Electrically Heated Oven; 8 Cool Down Fans; 2 - Hydraulic Lift Tables; Panel Machine with Hydraulic Pump; 15’ Flash Off Conveyor; 40’ Cool Down Conveyor Includes the following for (two) flood coat machines, Conveyor System, Arbors, Paint Pump, Hydraulic Pump, Hydraulic Lift Table -- Complete Over-all Foot Print 175’ long x 50’ wide

DEKKER VMAX 40 HP Vacuum Pump (Liquid Ring):40 HP oil-sealed liquid ring compact motor-mounted vacuum pump system, 550 CFM, max. 29" Hg. -- Heavy duty construction:Compact design, small footprint, patented, high-efficiency DX-5 separator eliminates oil carry-over concerns; Engineered for continuous operation. -- Extended lifeSeal-fluid is not used as a lubricant. Change interval is not critical, resulting in a minimum of (10,000) Hrs. of continuous operation. Sturdy bearing pedestal mounts to standard NEMA, C-face motor. -- Direct drive and withLow speed (1,750 RPM) eliminates the use of V-belts, resulting in very low maintenance and zero downtime.Over the full vacuum range without overheating. Air cooled design and low operating noise level.

DELTA - 22-650, ...Single Planer.DELTA/INVICTA 12" Table Top (no stand) Single Planer equipped with: 2 HP motor; 3-knife round cutterhead; with rollers.Capacity of 12"; feed rate of 15-1/2 FPM.250 LBS

Delta RC-63N 24" PLANER WITH SPIRAL CUTTER HEADSpecifications -- 24" x 9" Cap., 5/16" max. material removal, -- 10-1/2" min. part length. -- 15 HP Belt drive motor, -- Spiral Cutting Head -- 5,000 RPM, variable feed speed from 20 - 60 FPM.Equipped with & Features -- Powered raise and lower of 25" x 35" table, -- Sectional chipbreakers, sectional infeed roller & dual outfeed rollers. -- Push button magnetic control, -- Dust hood, & grinding attachment to sharpen helical head knives while on the machine.

DELTA RC-51 PLANER20" x 9" Cap., 7.5 HP motor, 4-knife cutterhead, power raise-and-lower adjustment and fine adjustment thru a convenient hand wheel; variable feed speed 16 - 28 FPM; equipped with sectional chipbreakers, adjustable bed & dual outfeed rollers. Actual model 22460

DELTA - UNISAW, ...Table SawSpecifications: -- 10" Blade dia., 3 HP - 3,450 RPM motor belt drives 5/8" dia. arbor @ 4,000 RPM, arbor tilts 0° - 45°. -- 3-1/8" Max. depth @ 90°; 2-1/8" max. depth @ 45°; 25" max. rip cap. to right of blade and 15-1/2" max. to left of blade, 13/16" max. dado width. -- Includes: 27" x 40" Cast iron table, distance front edge of saw to blade 12-1/4", 34" table height; DELTA Rip Fence; (1) set of dado blades.

DELTA RS-15 SINGLE SPINDLE SHAPERSpecifications: -- 1-1/4" interchangeable spindle. -- 7.5 HP motor with (5) spindle speeds of 2,800 - 4,500 - 6,000 - 8,000 & 10,000 RPM. -- Vertical spindle travel is 7-3/4", with 5-5/16" capacity under the nut. -- 35-1/2" x 43" fixed table with 13" max. table insert diameter.Complete with: -- Spindle reversing switch, spindle foot brake & lock, and adjustable fence. -- HOLZ Power Feeder is included

DELTA 11-990C 12" 5-Speed Bench-Top Drill PressSpecifications: -- Table size 8-1/2" x 8-1/2" with 15-1/2"; x 40"; x 11/16"; Thick Plywood top, Table tilt 40° Left/Right. -- Base size 8-1/4" x 8-1/4". -- Quill travel 2-3/8", Chuck capacity 1/2", JT33 Spindle taper. -- Spindle speeds 620, 1,100, 1,720, 2,340, & 3,100 RPM.Equipped with: -- 1/3 HP - 1,720 RPM Motor.Complete with: -- Portable Wood Cabinet.Dimensions with cabinet: 41" x 36" x 57" H

DENRAY 2800 Down Draft TableConvenient size 28" x 48" table. -- 2,800 CFM Rating at 1" static with 1-1/2 HP motor. -- Space-saving self-contained unit with no ductwork and no loss of conditioned air. Tube filter system cleans with 99% capture rate at 1 micron. -- Comfortable 36" working height. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick steel-reinforced MDF board and rubberized surface. -- (4) 4" Swivel casters with (2) that lock. -- Options available; Exhaust Muffler to reduce sound level 10 - 12 dBA, Magnehelic Gauges, HEPA Filter Banks, 3-Sided 20" Shields and Odor Control Filters. -- Also available in 230V, 460V and 575V, 3-Ph

DENRAY 2872 Down Draft TableLarge work surface on this 28" x 72" table (overall). -- Rated at 3,400 CFM, with 2 HP motor and magnetic starter. -- Space-saving self-contained unit w/built-in dust drawer. -- Features; New Tube Filtration System which cleans with a 99% capture rate at 1 micron. -- Quiet operation at only 77 dBA sound level. -- Comfortable 34-1/2" working height. -- 3/4" Thick steel-reinforced MDF board worktable with "non-marring" rubberized surface. -- Easy manual filter cleaning. -- (4) Casters, (2) of which lock in place. -- 115 Volt receptacle with 8' cord. -- Available options; Exhaust Mufflers to reduce sound 10 - 12 dBA, Magnehelic Gauges, HEPA Filter Banks, 3-Sided 20" shields and Odor Control Filters. -- Also available in 230V, 460V and 575V, 3-PH which includes magnetic starter.

DENRAY 2896 Down Draft Sanding Table: Extra long 28" x 96" table with a 36" working height. -- Rated at 3,500 CFM with 2 HP single phase motor. -- This model features the New Tube Filtration System which cleans with a 99% capture rate at 1 micron. -- Includes: (4) Swivel casters, including (2) that lock in place. -- No duct work, no loss of conditioned air. -- Comfortable 1-1/8" thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- Available options include; Exhaust Muffler to reduce sound 10 - 12 dBA, Magnehelic Gauges, HEPA Filter Banks, 3-Sided 20" Shields and Odor Control Filters. -- Also available in 230V, 460V and 575V, 3-PH.These tables are popular with small to medium shops to incorporate (2) operators side by side or for use on longer products.

DENRAY 9600 B Down Draft Sanding TableExtra large 48" x 96" table; Comfortable 36" working height. -- Powerful system with 4,800 CFM rating. -- 5 HP Motor with magnetic starter. -- Space-saving self-contained unit w/built-in dust drawers and high efficiency cartridge filters. -- No duct work, no loss of conditioned air. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- Fully enclosed unit. -- "Self-Cleaning" System with push button start to force compressed air from a storage tank into the filters and force dust into the dust drawer. -- Floor level air exhaust that can be directed away from operator. -- Quiet operation with only 82 dB. -- Available options; (4) Swivel casters with (2) that lock in place, Auto-Self cleaning timer or muffler.

DENRAY 7200 B DOWN DRAFT TABLELarge 48" x 72" Table. -- 3,900 CFM rating after filters. -- 5 HP Motor w/magnetic starter. -- Space-saving fully self-contained unit: No duct work, no loss of conditioned air. Contains (2) cartridge filters that clean to 0.5 microns. -- Comfortable working height 36". -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- "Self-Cleaning" System with push button start to force compressed air from a storage tank into the filters and force dust into the dust drawer. -- Floor level air exhaust which can be directed away from the operator. -- 84 dBA Sound level. -- Options include; Timer to automatically clean filters without operator, (4) swivel casters (2) that lock into place, noise reducing muffler (Reduces volume by 10 to 12 dBA),Unit also available in 220 V single-phase.

DENRAY 3660B Down Draft Sanding TableConvenient 36" x 60" table with a 36" working height with DENRAY's Pulse jet Cleaning System. -- Rated at 3,400 CFM for fast, easy removal of dust. -- 2 HP 3-phase motor. -- Space-saving self-contained, double filtration unit with integrated table top surface filter and bottom filters on all (4) sides. -- No duct work, no loss of conditioned air. Sound level 74 dBA. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board with rubberized surface. -- Also available in 115 V and 220 V single phase

DENRAY 3672 B Downdraft Sanding Table.Convenient 36" x 72" Table, comfortable 36" working height w/ DENRAY's Pulse Jet Cleaning System. -- Rated at 3,500 CFM. -- 2 HP, 3-Phase motor with magnetic starter. -- Self-contained system with 80/20 cartridge filters which clean with a 99.95% capture rate at .5 microns. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- Space-saving design with no duct work, no loss of conditioned air. -- Sound level at 78 dBA. -- Available options include: Exhaust chimney, exhaust mufflers to reduce sound level to 10 - 12 dba, casters and filter cleaning auto timer.

DENRAY 9600 Down Draft Sanding Table: Extra long 48" x 96" table with a 36" working height. -- Rated at 4,300 CFM with 3 HP motor. -- This model features the Tube Filtration System which cleans with a 99% capture rate at 1 micron. -- Includes: (4) Swivel casters, including (2) that lock in place. -- No duct work, no loss of conditioned air. -- Comfortable 1-1/8" thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface.

DENRAY 2872 B Down Draft Sanding TableThis model is great for medium sized jobs, and can be used for plastics, woods and finishing materials. The 2872B comes with 80/20 cartridge filters which clean with a 99.95% capture rate at .5 micron. This model comes standard with Denray's "Jet Pulse" push-button cleaning, rubber coated top, along with motor access on the left end and filter access on the right end.Large work surface on this 28" x 72" table with DENRAY'S Pulse Jet Cleaning System. -- Rated at 3,000 CFM, after filters, with 2 HP motor and magnetic starter. -- Space-saving self-contained unit w/built-in dust drawer. -- High efficiency cartridge filters (180 sq. ft. of cloth area) that clean dirty air to .5-micron. -- Includes: Push Button cleaning -- Quiet operation at only 74 dBA sound level. -- Comfortable 36" working height. -- 3/4" Thick steel-reinforced MDF board worktable with "non-marring" rubberized surface. -- This machine can be used in heavy wood, finishes, solid surfaces and stone type materials. -- Available options: -- Explosion Proof Motor (3 Phase only). -- Light Bar. -- Casters. -- Auto-timer. -- Muffler (reduces sound level 10-12 dbs.). -- 100% Spunbond Polyester FiltersCarbon Filter Bank (odor only). -- HEPA Filter bank. --Three-sided Hinged Safety Shield. -- Magnehelic Gauge. -- HDPE Plastic Tabletop. -- Hydraulic Height AdjustmentAlso available in 230V, 460V and 575V 3 Ph..

DENRAY 2872 G Downdraft Sanding Table for Metal GrindingDenray grind downdraft tables are made for the general grinding of ferrous metals and come equipped with water pans built over the filters to help protect them from hot sparks. The flame-retardant 100% Spunbond polyester cartridge filters clean to .5 micron. These tables come equipped with Denray's "Jet Pulse" push-button cleaning, which can be set with an automatic timer.Includes: -- 28" x 72" Table top work area. -- 36" Work height. -- 3 HP motor w/ 3,600 CFM. -- 18" Fan. -- 76 Decibels Sound Level. -- Auto-timer. -- Magnehelic Guage Available Options: -- Explosion Proof Motor (3 Phase only). -- Light Bar. -- Casters. -- Muffler (reduces sound level 10-12 dbs.). --Carbon Filter Bank (odor only). -- HEPA Filter bank. -- Fiberglass Grate top. -- Rubber Mat for Steel Tabletop. -- Stainless Steel Tabletop. -- HDPE plastic tabletop. -- Hydraulic Height Adjustment. -- Smoke Arm. -- Larger Motor/Fan Up-grade?

DENRAY 9600 B Down Draft Sanding TableExtra large 48" x 96" table; Comfortable 29" working height. -- Powerful system with 4,800 CFM rating. -- 5 HP Motor with magnetic starter. -- Space-saving self-contained unit w/built-in dust drawers and high efficiency cartridge filters. -- No duct work, no loss of conditioned air. -- 1-1/8" Thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface. -- Fully enclosed unit. -- "Self-Cleaning" System with push button start to force compressed air from a storage tank into the filters and force dust into the dust drawer. -- Floor level air exhaust that can be directed away from operator. -- Quiet operation with only 82 dB. -- Includes: (4) Swivel casters with (2) that lock in place, Auto-Self cleaning timer or muffler.