Yates A20-12 Planer Infeed Deck Tilt Hoist 575 V Includes: Misc parts, heads and attachments for S4S and T&G. This system was removed from service this Spring. It is ready to load.

Used Yates American Model B-26, 24” Double Planer, 75HP top, 40HPBottom, top and bottom 10 knife cutterheads, on the fly top and bottom jointers, 3 phase 480volt electrics, slide out lower cutterhead, top fixed cutterhead, 3-3/4” thickness capacity, approx. 20HP hydraulic feed works, power bed raise and lower, sectional pneumatic chip breaker, top infeed/outfeed rubber rollers.

Planer Head Set Up Stand

The frame is a massive, compact and solid casting which takes less floor space for its capacity The feed drive is built to stand up under the hardest kind of services The feed rolls are of such design that the advantages of the open side type of construction are combined with of the advantages of the inside The top and bottom head assemblies are of the most substantial construction The top head chip breaker is made of chilled cast iron section, each section being spring loaded and adjustable The side head spindles are short and of large diameter The side head chipbreaker moves in and out with the head and is also provided with an additional screw adjustment for close setting The bedding is continuous throughout the entire length of the machine

220v 3 phase 2hp motor Controls work, motor runs and spindle turns Spindle raising mechanism has pin sheared in bevel gear. Includes overarm casting & mobile base.

The seller has confirmed that this Yates American resaw was in working/running condition when it was pulled from production. It is ready to load! - Vertical resaw - All parts and blades included - Approximately 35 years old - 50-60HP - 440 amp

There are two of these systems available. They were recently removed from the current operation and available immediately.

Yates American E-12 End Matcher System for tongue and groove flooring includes: Belt, Straight Line Blade, 3-blades, Infeed conveyor to end matcher, transfer conveyor from first machine to second machine, variable speed outfeed conveyor

Yuasa saw analyzer, great working condition comes with saw centers, magnifying camera and monitor.

Air Compressor Water Separator Single Phase 115V 16hz Good Condition

Recently removed from service Available immediately

This line is for sale as one lot. 1. Vertical Reciprocating Conveyor (VRC) - 106x80x72 - Roller Dimensions: 94x3 inch diameter - 72" wide roller deck 2. Chain Transfer Conveyor - Space between rollers is 4 feet (size of Transfer deck) - Rollers on each side measure 94x3. - Roller housings on each side measure 72x96x26. -Total dimensions: 72x224x26. 3. Straight chain driven Conveyor - 72x100x26 - 8' rollers 4. 360° rotating turntable conveyor -Base dimensions: 74x58 -Roller dimensions: 40x3 - Conveyor Dimensions: 72x48x26 5. Straight belt driven conveyors (4 of them) - 54x12x12 belts not included 6. Curved belt driven Conveyor - Exterior curve: 224x48x26 - Rollers are 40" long and vary from 2-4.5" wide along curve. 7. Line conveyors (2) - 144x36x24 - Rollers available for this 8. Stacked rollers -96x66x75 - Roller dimensions: 80x3 9. Straight Gravity Rollers (18 of them) - 148x36x6.25 These rollers were stacked 4 high. Legs are available to stack them or they will work in line. 222' run consisting of 18 pieces. 10. 32' decline belt conveyor - This has damage. See last photo.

4- Head customer built resaw 6" Wide belt Hydraulic hold down rollers 15 HP Motors on each head Pneumatic tension

Custom Built Heavy Duty Scragg Deck C55B rooftop chain 3’-7’ legs, 33’ long, 30” wide, 24’ catwalk, hydraulic motor drive

Single Head Pallet Notcher - New with warranty! 7.5 HP Motor 220/440 3PH Maximum Notch Size: 9" x 2-1/2" x 1-5/8 Power switch with magnetic starter Cutterhead with 4-straight HSS knives (optional 40 knife cutterhead) Dimensions: 48" L x 36" W x 40" H

Single Head 4 blade Notcher: custom built, lightly used Motor 10 HP, 220/440V, 3 phase Maximum notcher size 9” long x 2-1/2” height x 1-5/8” depth Cutterhead with 4 straight HSS knives installed

Custom Built Single Head Notcher Manual

Custom Built Single Head Notcher Manual

Each system is custom built to fit your specifications. Standard Electric Lateral Chain Feeders include Basic Feeder with transport length of 30" Workpiece width 3/4" - 9-1/4" Min. Workpiece length 12" Drive system with 4 HP total drive system Feed speed range 50 - 250 ft/min (up to 400ft/min available) Thickness 1/4" - 4" Steel flat top chain 60 Cycle per minute Adjustable Fence 35MM Feed Wheel Shafts Options 6'-16' Lateral Chain Feeder Feed Wheel Knurled, Urethane or Light Knurl Hub Options 3/4" or 2" Powder Coating Bridge Side Fence Feed Speeds up to 400 FPM Short Stock Fence 12" Wide Capacty

This line will produce 4-5 bags per minute. Outfeed conveyor from each line Optional: Infeed auger and shaving bin