CP100 Can Flattener --220V, 1200 lbs per hour --Infeed Conveyor --Magnetic Separator -- New belt included

CRAFTSMAN DP-65 Drill PressSpecifications: -- Capacity: 15" -- Motor: 0.33 HP Equipped with: -- Push button control -- Stand

CRAM-A-LOT - HX-60: Closed Door Baler with Cart Dumper & Infeed ConveyorSpecifications: --The CRAM-A-LOT "HX-60 HH" & "HX" Series Balers are ideal for warehouses and designed for ease of installation, operation, and maintenance. -- CRAM-A-LOT® HH & HX Series Balers are: Built with extra Heavy-Duty construction; ideal for warehouses & recyclers who deal with large quantities of corrugated and paper products.Baler is designed for long hours of operation and can operate either manually or automatically with photocell control. Optional custom-engineered Feed Conveyors and Cart Dumper Systems efficiently control Baler feed rates for optimum performance in a complete Baling System.Standard Features include:ANSI Z245.5 Compliant: All Compactors meet or exceed ANSI Z245.5 safety standards.UL/CUL Listed Control Panels.UHMW Ram Shoes: Adjustable to assure straight tracking and readily replaceable, should the need arise.Oil Sight Gauge: Oil level at a glance.Oil Filter: Replaceable "spin-on" cartridge to keep your oil clean.Heavy-Duty Controls: NEMA 4-Rated pushbutton controls with "key lockable" start switch.Automatic single-cycle operation. -- Bale Size: 60" x 30" x 40". -- Bale Weight: Up to (OCC) 1,400 Lbs. --Throughput: (OCC) 2-1/2 Bales /Hr. -- Cylinder: 7".

CRAM-A-LOT - SCR-T2-34: (3) 34-Yard Self-Contained CompactorsNOTE: Lot of (3) Specifications: -- Cylinder: (2) 4". -- Main motor: 10 HP. -- Feed opening: 41″ x 58″ (1,041 mm x 1,473 mm). -- Capacity: 34-Yard. -- Ram force: Up to 24 tons.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6k ROCKWELL/CRESCENT 5-Head Single Head Tenoner Equipped with: Manually-operated sliding table. (1) Top & (1) Bottom Tenon Heads, Each with 2 HP Motor, (1) Top & (1) Bottom Cope Heads, Each with 1 HP Motor, & (1) 7" Cutoff head with 1 HP Motor.

CROUCH - 81-70 ...Edge Sander (Non-Oscillating)5 HP Direct drive motor; 6" x 144" abrasive belt size; (1) 8" x 56" Platen.Equipped with: -- (1) 12" x 56" Adjustable side table and (1) 15" x 28" end table.Tables adjust vertically 5" and laterally 2-1/2". -- 8" Dia. rubber covered drive pulley and 4" dia. aluminum idle pulley.

CROWN RC3020-30 Stand-Up ForkliftSpecifications: Load Capacity: 3,000 Lbs -- 3-stage mast -- Max. lift height 190" -- Clearance height: 89" lowered -- Battery drive train: 24VEquipped with: -- Side shift -- cushion tires -- Overhead guard -- Power steering and SCR travel controllerNOTE: Order Picker is not running, Battery is charged, needs wiring harness

CSMI Hi-Tech Optimized Board Edger. Complete with the following features: -- Two-saw Edger. --Top reman Head and System. --Infeed. --Unscrambler. --Scanning and Optimization. NOTE: Offered earlier at $75,000.

CUMMINS - 682-FDR-036JJW, ...1000K DIESEL GENERATORSpecifications: -- Output: 480/277 / 3-Phase -- 1,000 kW -- 1,250 KVA -- 1,504 Amps -- 1,800 RPMNOTE: (299) Hours on meter in factory-built enclosure. - Available for inspection!

Custom Built Disc Scalper;Includes the following features: --3 Ft. Wide X 10 FT. Long. --Fitted with 9 Rows of Discs, shaft mounted. --Drive Chain connected Row-to-Row. --Motor Platform (no motor or reducer). --Mounted onto a Steel Frame. --Bottom and End Discharge.

D M C - UNISAND 135, ...3-Head Wide Belt Veneer & Finishing Sander. -- General Data:3-Head, 51" (1,300 mm) nominal width cap.; motorized part thickness opening with LED readout; 1/8" to 4" max. - Head sequence: Cross belt, rubber-covered Drum, Pad. Head Configuration/Specs: -- 1st Head: Cross belt with: EPICS 44 Segmented electronically controlled air platen; 2-speed abrasive belt; approx. 36/72 FPM (11/22 MPS) linear speed; driven by 19 & 24 HP motors; 6" wide x 238" (6,050 mm) long abrasive belt. Inside synchronized Chevron belt, approx. 228" (5,800 mm) long.Pad unit with pneumatic cylinders: Each acting on a high absorption felt strip; working pressure controlled via control panel. HYDRA Belt: 2' Electronic control with oscillating blower for cleaning. -- 2nd Head: Rubber-covered 45-durometer steel roll, 9.8" (250 mm) dia. with: 18 HP 2-speed motor, 52" x 103" (4,055 mm) long oscillating abrasive belt with electronic tracking; air blast abrasive belt cleaner. Belt runs approx. 3,550 FPM (18 MPS) linear speed; adjustment & indicator of working position. -- 3rd Head: Flexible Sanding Platen with: EPICS 44 Segmented electronically controlled air platens; 3-speed 24 HP motors; 52" x 103" (4,055 MM) long abrasive oscillating belt with electronic tracking, timed oscillating air blast abrasive belt cleaner.Pad unit composed of: Pneumatic cylinders, each acting on a high absorption felt strip. Working pressure controlled vial control panel. Special rails allowing a quick change of graphite cloth on pad. Interchangeable system to modify the hardness, stiffness, and profile of the contact surface. Controller: -- DMC "HYDRA 30" Upgraded computer with: Working position display modes mounted in a separate control cabinet; automatic thickness device reads and adjusts feet table height, motor load meters. Transport Belt Drive: -- Variable feed speed of 16 to 82 FPM, conveyor feed drive, infeed & outfeed holddown pinch rolls on all heads; infeed hand safety stop, outfeed emergency stop; high efficiency dust extraction and separate control console with monitor, keypad, etc. Also included: -- Cleaning brush head at machine discharge. -- High pressure vacuum blower. -- Dust manifold. -- Extended outfeed table.

DMC - UNISAND 2000-M2, ...Wide Belt Sander (2) Heads -- 53" Width cap. Drum, Platen.Head Configuration: --1st Head: 11" dia. (300 mm) Rubber-Covered Contac; (2) speeds or inverter adjustable 20 - 25 HP; Varied RPM. --2nd Head: Combination head with drum and graphite covered 2-1/2" finishing platen; 25 HP.Specifications: -- 54"x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computor controlled; set-up functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with: 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with: LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, motor load meters.2-Roll infeed conveyor extension; high efficiency dust extraction.

DMC - EuroSystem SY-TC 1350, ...Heavy-Duty 4-Head Wide Belt Sander53" Width cap. Drum, Drum, and Drum; Segmented Platen.Specification; -- Max. workpiece width: 53". -- Workpiece thickness: 0.32" - 6.8".Head Configuration & Feed: -- 1st Sanding Unit: 10"; Diameter grooved steel contact drum; 60 HP motor. -- 2nd Sanding Unit: 10"; Grooved rubber covered drum, 27 HP motor. -- 3rd Sanding Unit: 10"; Grooved rubber covered drum; 20 HP Motor. -- 4th Sanding Unit: Electronic segmented platen; 35 HP motor. -- Belt size of 53" x 103". -- Feed Motor: 5 HP, Variable feed speed. -- Vacuum Bed. -- Constant Pass Line.Equipped with & Features: -- Power Panel Touchscreen Control. -- Shoe type holddowns. -- Amp meters for all Sanding Units.

DMC - 1350 RK, ...TECHNOSAND Dual Head Wide Belt Sander.(2) Heads, 52" width cap. - Head sequence: Contact sanding roll and Segmented platen. Head Configuration:1st Head: 7" (175 mm) Dia., 85 durometer rubber-covered calibrating contact sanding roll.2nd Head: Segmented finishing platen with EPICS (sectional electronic pad) with (46) electronically controlled air segments.Specifications: -- 53" x 103" Long abrasive belts with electronic tracking on all wide belt heads. -- Turbo panel blowers, timed abrasive belt air cleaners. -- DMC "Hydra 35" control, "EPICS" control for sectional platens. -- (99) Programs; graphic screen for machine configuration, +/- control on segmented platens, abrasive belt cleaners. -- Sequential automatic start-up, machine troubleshooting and self-diagnosis. -- Variable feed speed from 15 - 60 FPM (4.5 - 18 MPM), 1.5 HP feed drive, vacuum conveyor bed with 7.5 HP suction fan and motor.Equipped with & Features: -- Automatic conveyor belt tracking, infeed & outfeed holddown pinch rolls or shoes on all heads. -- 0" - 4" Motorized programmable thickness adjustment with LED readout. -- Automatic part thickness adjustment, infeed hand safety stop, outfeed emergency stop. -- Motor load meters and control console with monitor & keypad.NOTE: Message from the Seller: The machine was setup by a DMC tech. It has a new calibration roller & new bearings, rebuilt HYDRA 35 controller; currently under power, comes with dust collecting manifold and hoses, plus the machine can be loaded onto a flatbed for ...$ 600.

DMC UNISAND K (3) Bottom and (3)Top heads wide belt sander. --, 43" max. width. - Bottom Head sequence : 1st Head Contact roll, approx.18.5 KW motor- 2nd Bottom Head Contact roll, 2rd Bottom head, Combination head with roll and platen , approx.15 KW 2-speed motor, belt speed 118 m/sec. -- Bottom panel brush. -- Top Heads: 1st Top Head: Rubber covered contact roll approx. 18.5 KW motor, 2 speed, belt speed 9/18 M/Sec. adjustable contact roll with pneumatic grit adjustment. 2nd and 3rd Top Head: Combination head with Rubber covered contact roll and polishing platen, approx. 18.5 KW HP motor, adjustable contact roll with pneumatic grit adjustment.Top panel brush. -- 44"x 103" abrasive belts with electronic tracking; computer controlled set-up functions with key pad and LCD screen. -- Vacuum Conveyor feed belt with variable feed speed from 11 - 60 FPM, approx. 7.5 KW HP feed drive, automatic conveyor belt tensioning & tracking. -- Infeed & outfeed holddown pinch rolls on all heads, motorized part thickness opening with LED readout, 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Complete with: Infeed safety stop, outfeed emergency stop, motor load meters, high efficiency dust extraction and control console with monitor. -- Actual model USK1350-IM3 + USK1350

SCM DMC 90 RCS 135 2 Head 53 inch Wide Belt Sander 53" Width cap, Steel Drum, Combination HeadHead configuration1st Head: Steel Drum 36 HP Motor, 9" Diameter 2nd Head: Combination head 65 shore drum and solid wood platen, 30 HP Motor, 7" Dia. drumSpecifications: -- 54" x 103" Abrasive belts with electronic tracking. -- Shoe & Roller Holddowns. -- "Hydra 35" Computer controlled; set-up functions with a keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM; 6.4 HP feed drive. -- Vacuum conveyor bed with 7.5 HP Motor and suction fan. -- Automatic conveyor belt tensioning & tracking. -- Motorized part thickness opening with LED Readout; 1/8" - 4" max. opening; automatic part thickness set-up sensor. Equipped with & Features: -- Infeed safety stop, outfeed emergency stop, -- Motor load meters. -- 2-Roll infeed conveyor extension; -- High-efficiency dust extraction.NOTE: Specs have to be verified

DMC UNISAND K 1100 Wide belt sander4-Head, 43" (1,100 mm) max. width cap. Head sequence: (3) Contact rolls and (1) Combi with roller and segmented platen.Heads configuration: -- 1st Head: Helical grooved steel contact roll, 10" dia., 48 HP motor. -- 2nd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. and 65-Shore covering hardness, 35 HP motor. -- 3rd Head: Helically grooved rubber covered contact roll, 12-1/2" dia. 45-Shore covering hardness, 30 HP motor. -- 4th Head: Combi head with roller covered with rubber, 30 shore and Finishing sanding pad unit , 30 HP 2-speed motor with segmented pads pneumatically controlled -- All heads use 44" x 103" (to be confirmed) abrasive belts and are equipped with electronic tracking, automatic tensioning, automatic emergency breaking, and oscillating sanding belt cleaners.Controls: -- "HYDRA V-PAD" 10" Touch-screen computer for setup functions, color LCD Display, allows operator to setup/recall part thickness, -- Conveyor feed speed (3.5 - 18 MPM), -- Abrasive belt direction, and reversible speed setting of 4th head. -- Conveyor belt feed with inverter control, feed speeds from 11 - 60 FPM, 5.5 HP feed drive; -- Infeed & outfeed holddown pinch rolls on all heads, automatic part thickness setup with the moving feed belt, -- 2-speed motorized part thickness adjustment, 1/8" - 6" max. opening; -- Infeed & outfeed motorized conveyor extension rollers, automatic part thickness setup sensor. Complete with: -- Safety stop at infeed, -- Anti-kickback device, -- Infeed & outfeed emergency stops, -- Motor load meters, i -- Infeed & outfeed idle rollers, -- High efficiency dust extraction, and control console with monitor.Note: (spare parts not installed) New feed belt , new front pressure roller, new front pressure bar and several new small parts for approx $15,000 of value +11 boxes (approx 5 belts/ box) sanding belts 100 grit, 120 grit, 180 grit and 220 grit.

DMCTC 1350-M2-RP Orbital Sander (2) Heads --53" Width cap. Drum, Combination Head --Head Configuration --1st Head:10" Dia. helical grooved rubber covered calibrating roller, 26 kw (34 HP) motor. --2nd Head: Rubber covered contact roller with finishing platen 18 kw ( 28.5 HP) motor. --Specifications --Working width 1350 mm --Max thickness 170 mm --Belt size both heads 1370 mm X 2620 mm --Feed speeds variable from 3.5 -18 m/min. Feed motor 2.2 kw ( 3 HP) motor --Equipped With --Electronic sanding belt oscillation --Exhaust hoods with 4 outlets --Motor safety switch for main motor --Power rise and fall --Panel cleaning brush --Sander dim. L 2600 mm X W 2400 mm X H 2550 mm --Weight 2900 kg. --There is a crack in the plastic housing but it does not affect the functionality of the machine.

DMC UNISAND 2000 M3 Wide Belt Sander (3) Heads53" Width cap. Drum, Combination Head, Segmented PlatenHead Configuration:1st Head: Rubber covered contact roll 9" dia. 29 KW motor2nd Head: Combination Head, contact roll with graphite platen 21.4 KW motor3rd Head: Electronic Segmented Finishing platen with (46) segmented pads 18.5 KW motor.4th Station: Panel cleaning felt type head 1.74 kW, 460V, 3-phase, plus Air Cleaning headsSpecifications: -- 54" x 103" Abrasive belts with electronic tracking -- Computer controlled setup functions with keypad and LCD screen. -- Conveyor belt feed with variable feed speed from 11 - 60 FPM, 3 HP feed drive -- Vacuum conveyor bed with 10 HP motor and suction fan -- Automatic conveyor belt tensioning & trackingEquipped with & Features: -- Infeed & outfeed holddown pinch rolls on all heads. -- Motorized part thickness opening with LED readout. -- 1/8" - 4" max opening, automatic part thickness set-up sensor. -- Infeed safety stop, outfeed emergency stop, motor load meters --High efficiency dust extraction. -- Control console with monitor.Note: Dust manifold included

D M C FINESAND 130 2PO WIDE BELT (50" - 90", 2-HEAD): -- Specifications:Orbital Pad Sander, designed for cross-grain scratch removal on style & rail frames; with (2) Orbital Platens & (1) Brush. -- Working Capacity: Width 51", height/opening 1/8" - 4-5/8", motorized part thickness adjustment with digital readout, (4) screw jacks rise & fall. -- Sanding Heads: (2) 10" Wide Platen heads with rubber surface for elimination of abrasive belt cross-grain scratches. Dual orbital action heads with (1) high speed orbit on sanding pad, powered by 5.5 HP motor, and a secondary "low RPM" orbit on head assembly (1.5 HP motor), superimposed over the high-speed orbit for fast cutting action. -- Rotating Cleaning brush on outfeed side. Abrasive material for Sanding Heads is 18" x 52" in size. -- Feed Conveyor: Variable feed speed from 6 - 40 FPM, inverter controlled by 5.5 HP motor; vacuum conveyor bed with 15 HP blower motor. -- Complete With: - Digital height readout. - Infeed and outfeed rubber coated hold-down rolls. - Infeed hand safety stop bar, emergency e-stop. - Star-Delta motor starter. - (2) Dial indicator motor load meters.