SANDMAN M7236 Downdraft Sanding Table110V 1 HP (M7236) T.E.F.C Motor with 15’ power cord. -- 72" x 36" Rubberized work surface. -- 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 5" wheels, (2) ridged and (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Grid system top adds versatility. -- (18) Month warranty on parts.NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN DL9648 Downdraft Sanding TableThe DL9648 is a dedicated 96" x 48" sanding table that doubles as a workbench. The Sand Pro DL9648 is perfect for sanding large pieces such as doors or as a multi-person sanding station. Specifications: -- Table height 36", table size 96" x 48". -- (2) 1.5 HP TEFC motors with 7,400 CFM @ 1.5 SP and (2) 16" backward inclined fans. -- (6) Extended surface pleated filters each 20" x 25" x 2" deep w/ 1/2" netted polyester filter. Features: -- (4) 110 V duplex receptacles. -- Rubberized mar-proof top. -- Grid system top for jigs and fixtures. -- Hinged top with gas strut lid support for easy access to filters. -- (2) 10" x 32" Shelves. (2) 18" x 24" Storage drawers. -- Stainless steel hanger for air orbital sanders (choose 5" or 6"). Options: -- 3" Swivel casters (Adds 3/4" to machine height). -- Case of (12) replacement filters. -- Single phase available -- 18 Month Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN M74836 Downdraft Sanding TableGreat sanding table for a singular function such as doing cabinet doors, door fronts, etc. This downdraft table has a 6″ overhang on the front side making it good for sanding while sitting. Machine comes standard with casters, utility tray, & Felt-lined Platforms.Specifications: 48 L x 36" W top surface with heights of 32", 34" $ 36". -- Overhangs of 6" front. 0" back and 4" ends. -- (2) DP20252 Filters and (1) PF4029 pre-filter. -- 1 HP Baldor Motor – Standard Single Phase 110V (13 Amps) -- (18) Month warranty on parts.(Single and 3-Ph 220V available)NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDVIK - QJ241: Jaw Crusher -- New in 2015. - Tier 3 Engine. -- Productivity: Highly productive; 1,000 x 650 mm; 40"; x 26"; jaw opening for maximum throughput. -- Hydraulic CSS jaw setting adjusted using control panel or handset; to avoid interruptions. -- Load sensing system for feeder drive & jaw level sensor ensures continuous crushing. -- Ideal for Recycling with: Reverse crush, overband magnet, and hydraulic raise & lower facility on main Conveyor for rebar clearance.

SANI-TECH -, ...Auger Compactor -- Motor: 10 HP. -- Hopper capacity: 4.3 Cubic yards. -- Auger RPM: 10. -- Displacement rate: 270 Cubic Yards/Hour. -- 20-Yard Compactor

SAS SCORPION ENGINE PULLER Model SC40 DescriptionIncrease cash recovery from your recycling operationsSAS Forks Scorpion High Speed Motor Puller – Scrap Yard Engine Puller – Auto Recycling Engine Puller – Excellent for self service yards processing vehicles before crushing.Generate revenue:Process end of life vehicles in less than 60 seconds.Pull scrap engines and transmissions in 30 seconds.30% more revenue by separating metals from bodies.1000% more revenue per lb. on wire harness from engine compartment and dash.80% more visibility with a direct line of site from the operator’s window through the forks.Cycle time less than 15 seconds from park to full extension.Serviceable for long life. Replace blades in 3 hours or less.estimated only.Engineered & built for optimum performance:Engineered tough for continuous prying and durability.Hardened pins and bushings and grease-able pivot points for extended service life.Hydraulic hoses and cylinders are protected to minimize potential damage from sharp objects.Built with high strength blades and carriage skid plates for extended service.Clean up of ground debris is a snap with center plow blade.Speed is paramount in this design. Operator uses grapple from the cab, no torches, no personnel needed to hook up chains to pull or move engines. Safer, quicker and less costly removal of engines and transmissions.

SAVI HFK-250 Veneer Guillotine; General Specs: -- 102.4" (2,600 mm) Width cap., 4" daylight opening, hydraulically operated knife, 4 HP Leroy-Somer motor powers hydraulic unit with reservoir. -- Originally fitted with motorized parallel fence with 0.5 HP two speed gearmotor drive, push button operated, adjustable from 1" - 50" with magnified tape reader in front of machine. -- Equipped with: 2nd Cut feature with automatic reset, laser guide line light, photoelectric barrier guard for knife & hold-down beam, 2-hand operation of knife cycle. -- Note: Rear fence has been removed or modified. Shaft has chain/sprocket.

SAWSTOP CB 73230 Table Saw w/Famous Safety "Stop Feature".10" Blade cap., 7-1/2 HP - 3,450 RPM motor, 3-1/8" depth of cut @ 0°, 2-1/4" depth of cut @ 45°, 13/16" max. dado width, 5/8" arbor dia, 30"; FB x 24"; LR Table, with 45° Left tilt, & 10"; Left & Right extensions. -- FEATURES: Enclosed cabinet, heavy-duty belt drive, cast iron trunnions, and SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: Rip fence with 52" Right & 12" Left Rip cap., side support table and laminated top, 4" Dust collection port, magnetic contractor motor control, main power switch with removable lock-out key, & Accessories (As pictured).Actual model CB 73230.

SAWSTOP ICS 73230 Table Saw w/Famous Safety "Stop Feature" & New Sliding Crosscut Table.10" Blade cap., 7-1/2 HP - 3,450 RPM motor, 3-1/8" depth of cut @ 0°, 2-1/4" depth of cut @ 45°, 13/16" max. dado width, 5/8" arbor dia, 30"; FB x 24"; LR Table, with 45° Left tilt, & 10"; Left & Right extensions. -- FEATURES: Enclosed cabinet, heavy-duty belt drive, cast iron trunnions, and SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: Rip fence with 52" Right & 12" Left Rip cap., side support table and laminated top, 4" Dust collection port, magnetic contractor motor control, main power switch with removable lock-out key, New SAWSTOP "TSA-SA48" 48" Sliding Crosscut Table, & Accessories (As pictured).Actual model ICS 73230.

SAWSTOP - ICS 73230, ....Table Saw w/Safety "Stop Feature"Specifications: -- 10" Blade cap.; 7-1/2 HP motor; 3-1/8" depth of cut @ 0°; 2-1/4" depth of cut @ 45°; 13/16" max. dado width; 5/8" arbor dia. -- Features: -- Enclosed cabinet; Heavy-Duty belt drive; cast iron trunnions; SAWSTOPS's revolutionary flesh detecting safety mechanism. -- Includes: -- 52" "T-Glide" rip fence system; side support table and laminated top; 4" dust collection port; magnetic contractor motor control; main power switch with removable lock-out key. Actual model is: "ICS 73230"

SCHEER Veneer Panel Saw. -- General data: 122" Cutting length, 1-1/2" depth of cut, 3/4" - 42" max. back fence cap. with extension fingers, 5 HP arbor motor; saw carriage travels on hardened & ground ways. -- Equipped with: Manual operated saw carriage with hand crank Full-width rear fence with support, hand wheel operated rear fence with scale & arrow readout for positioning. -- Lockable fence at cutting position, fence line also pivots up to permit end trimming against the left guide fence. - Pneumatically controlled hold-down pressure beam. -- Complete with: Push button control and dust collection chute with channel in table base.NOTE: machine is currently in storage and can not be test run, we are told it was on working condition when placed into storage

SCHELLING FM-430/410 CNC Front Load Panel SawSpecifications & Features: 169" (4292 mm) Cutting length & 165.3" (4,200 mm) pull back, 3.75" (95 mm) max. saw blade projection; 25 HP (19 kW) 4,100 RPM main & 3.4 HP (2.5 kW) 5,600 RPM scoring motor. -- Equipped with: Variable saw carriage travel speed from 0 - 278.8 FPM (85 MPM), constant return of 278 FPM (85 MPM). -- Electronically controlled overhead program fence with rack & pinion driven on both sides; forward speed from 0 - 278 FPM (85 MPM), return speed of 278.8 FPM (85 MPM); equipped with (8) gripper clamps (open up to 5" (130 mm). -- Features: SCHELLING "COMPOSER" IBM-AT Compatible Computer Control; aftermarket color monitor (displays cutting dimensions and patterns w/moving graphics) , self-diagnostic, data input by keyboard; onboard optimization program. -- Complete with: 2-3/4" to 87" (2,200 mm) Long side/cross-cut aligning zone, (1) aligner in front & (1) behind the cut line. -- (3) Front mounted air float tables for moving panel from rip section to the cross-cut section, (2) movable and (1) fixed; each with their own blower. -- Rear of machine fully enclosed for safety with man-height sheet metal panels & wire screen windows. T

Schneeberger 9 Sculptor Profile GrinderSwiss Made, Schneeberger Automated High Precision Grinder for Finger Joint, router bits, saw blades, straight and milling Cutters. Specifications: -- Grinding Motor: 1,500 - 3,000 RPM. -- Cooling Pump: 2,800 RPM. -- Grinding Wheel Speed: 3,000 - 6,000 RPM. -- Grinding Wheel Diameter: 50 - 200 mm. Grinding Wheel Bore: 30 mm. -- Cross Travel of Grinding Wheel: 200 mm. Vertical Travel of Grinding Wheel: 400 mm. -- Grinding Head: Swivel-able. -- Worktable Travel: 400 mm. -- Coolant Capacity: 25 liters.Dimensions: 1,226 mm length x 1,160 mm width x 1,180 mm height; Weight - 320 kG.10" Width cap., 11.5" dia., max. profile depth 5.5", radial clearance angle up to 35ø, lateral clearance angle up to 15°Equipped with & Features; -- 2 HP - 1,500 RPM motor, variable grinding speed 2,000 - 4,000 RPM, three-sided full jet cooling. -- All std. grinding equipment for HSS grinding, 1-1/2" spindle arbor, (2) wheel flanges, (1) knife holder, and dresser.

--In Auction--Starting bid: $100-- Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Schuetz Tool Bladder Press Specifications: (2) Shuttle tables, approx. 55” x 106” press capacity. Hot air design with 3mm silicone membrane to press veneer into profile, typical cycle time 3 minutes using proper glue that sets at 200°F. Can use PVA which would extend cycle time to approx. 15 > 45 minutes depending on the actual glue mix used to achieve 80%+ cure strength. Includes Hydraulic Pump. SPECIAL NOTE: Fully operational, however, need 4 or 5 heating rods replaced, new rod parts are included for you to install ( don't have the capability to remove them). The current average operational temperature is 150° F. NOTE: Above specs are taken from literature and thought to be accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

SCHUTTE BUFFALO - Model WA16L, ... HammermillModel# WA16L, 3500 RPM, with filtration system and multiple grates for destruction sizes. -- It also includes Electrical panel. -- This system is apart and palletized. All you have to do is pick it up and transport it to you. -- System was in perfect working order when it was taken apart and palletized for transport. -- The system is perfect for the destruction of computer hard drives and different types of media.

SCM S 630 PLANER WITH TERSA HEADSpecifications: -- 24" Width cap.; 12 HP main motor, 2 HP feed motor; 4-3/4" dia. with reversible knife TERSA Planer Head rotates @ 4,500 RPM; -- 1/8" - 11-3/4" Thickness opening via motorized bed with LED readout for fine adjustment. -- Max. depth of cut 5/16"; 10" min. length of work piece; variable infeed speed from 20 - 56 FPM.Equipped with: -- 20-3/4" x 39" Cast iron table, sectional chip breaker, sectional grooved infeed & solid outfeed rollers, adjustable bed rollers. -- neoprene out feed rollersComplete with: -- Magnetic starter and dust hood w/6" dia. dust outlet.Owner states: Condition- like new 24" thickness planer- third owner in a one man shop. Machine has seen very few hours of operation.

SCM SANDYA - 40 M3 135, ...3-Head Wide Belt Sander 52" Width cap. Drum, Drum, Combination HeadHead Configuration:1st Head: Steel Contact 22 kW Pneumatic blowdown and alignment.2nd Head : Rubber Contact 18.5 kW Pneumatic blowdown and alignment.3rd Head: Combination Platen 15 kW Pneumatic blowdown and alignment.Note:The SCM sander does not have a brush. After the 3rd head, it has this pneumatic blow-off bar with multiple blow-offs running the length of the sanders width. Sander can be seen under power if needed.Specifications: -- 53" x 103" Abrasive belts with electronic tracking. -- All heads with abrasive belt grit compensation. -- Conveyor belt feed with dual feed speed, 5 HP motor. -- Automatic part thickness adjustment. -- Motorized thickness opening via (4) precision conveyor bed jacks with LED readout. --0" - 7-7/8" opening. -- Equipped with & Features -- Outfeed rubber covered holddown rolls or shoes on all heads. -- Motor load meters. --Infeed and outfeed conveyor extensions. -- WYE-DELTA soft start.Note: The SANDYA model "40" is more or less the same as the SANDYA "30" but more Heavy Duty.

STEFANI ONE TOUCH HEAVY DUTY PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + PUR/EVA Gluing Technology: -- Basic Specifications: Minimum Panel Spacing 24.625" (630 mm) between panels; Edge Thickness capacity 0.015" - 0.875 (0.4 - 22 mm); Panels thickness (min/max) 0.375" - 2,36" (10 - 60 mm);Minimum Panel Length 5.5" (140 mm), or 8.625" (220 mm) when "Corner Rounding; Processing Track Speed min/max 40 - 82 FPM (12 - 25 MPM) variable feed speed.FRONT-END EQUIPPED WITH: -- 2-Roll/Station Vertical Coil Magazine with "Automatic" change-over. Infeed Panel Heating Lamps. Spraying unit (Anti-sticking liquid). -- Pre-Milling: 4 kW (5.3 HP) - 12,000 RPM x 2 motors, with Diamond Tooling; -- Gluing System: "No-tool" "Quick-Change", Teflon coated Glue Pot; Electronic Controlled "Quick Melt" system with auto Kick-down."PU-BOX L" Gluing Unit Pre-Melting system with "Melt on Demand" for managing both EVA & PUR glue. all managed form the PC control.This unit "INCLUDES" the SPG Glue pot for PUR + the standard glue pot for EVA. "SPG" Glue Pot for managing both EVA & PUR Glue, capable of emptying the glue pot in 8-minutes, through the PC controller & can be disassembled in less then 10-minutes for cleaning & maintenance. -- Pressure Section: PC Servo Controlled with (1) large dia. clutch controlled drive roller and (5) pneumatic pressure idle rollers with opposite tilt traveling on THK guides, all rollers have "JUMP" capacity.Heavy-Duty Guillotine. 35 mm dia. Reversible glue roller for solid wood application, with clamping device to eliminate any glue transfer on the trailing edge.WORKSTATIONS: -- Top Mounted End Trimming:0.8 kW - 12,000 RPM Motors x 2; Motors Automatic Blade tilt from 0° - 22° on horiz. plane. -- Flush Trimming "R-E": "UPGRADED" 1.84 kW - 12,000 RPM motors x 2, Top & Bottom flush trimming station. -- Multi-Edge Finish Trimming: 1.1 kW - 12,000 RPM motors x 2; Top & Bottom bevel/radius trimming station with up to 30° tilt; NC controlled "Multi-Edge" kit for (3) automatic position, straight, 1mm radius & 2mm radius, preset through controller. -- Corner Rounding: (4) Motors (0.35 kW - 12,000 RPM each); 2-postition (1 & 2 mm radius) preset trimming through controller. -- Profile Scraping: NC Controlled, Top & Bottom profile scrapping units with 2-postition (1 & 2 mm radius) adjustment through the controller; PVC shavings collection box; air pressure nozzle to support removal of scrap. -- Glue Scrapers:Top & Bottom pneumatic controlled, flat scraping knives with bearing guide-wheels. -- Hot Air Edge Brightener:To re-embellish the color & help eliminate scrapper marks -- Oscillating Buffing Unit: 0.3 kW - 1,500 RPM motors x 2; Top & Bottom oscillating buffing wheels for cleaning/finishing material edges; units tilt 0° - 10° to prevent wear grooves in the buffing wheels.Operator Interface: -- Stefani "StarTouch" + Windows "XP" operator interface, with NC controlled adjustment for all working units.17' TFT screen; ETHRENET Network c

STEFANI KD-R EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): + EVA or PUR Glue System. -- Specifications:0.4 - 12 mm edgebanding cap., panel thickness (min/max) 10 - 60 mm (0.375" - 2.375"); panel width min 51 mm (2") panel length min 140 mm (5.5") variable feed speed 10 - 20 MPM (33 - 66 FPM), min distance between panels: 610 mm (24";). -- Front-End equipped with: Air Cushion infeed table, to facilitate insertion of large dimension workpieces, table dims are 1,600 mm x 600 mm.Infeed Fence with a mechanical digital indicator to position the fence and determine the stock removal.It is also equipped with a pneumatic panel spacing device to prevent the operator from feeding the panels to close to one another. -- Pre-Milling:Pre-Milling unit with (2) 4 kW (5.3 HP) - 12,000 RPM motors with jumping action controlled through the PLC.The cutting heads are adjustable vertically. The unit is equipped with copying devices which guarantee that material removal is consistent on long or slightly out-of-square panels.64mm Tall diamond pre-mill cutters with replaceable inserts. -- EVA + PUR Gluing System:Quick Melt system with approx. 8 - 10-minute heat up time. Includes an SGP "QC" Glue pot with less than 1-minute change-over time. Double Thermo Regulation for easy use of both EVA and PUR glue. Color change and glue pot cleaning are able to be completed in minutes, as opposed to hours.An automatic temperature kickdown feature extends glue life and reduces glue scorching. Reverse rotation of the glue roller for the application of solid wood.Equipped with "I-Glue", which locks the glue roller in place at the end of the panel eliminating any excess glue. -- Pressure Section:(1) large dia. Teflon coated clutch-controlled drive roller & (3) pneumatic pressure idle rollers with opposing one-degree tilt to provide extra pressure along the top & bottom edge. The pressure section is also equipped with pneumatic jumping, so the unit activates exactly on the leading/trailing edges via the edge detecting sensor that will shut down the feed track when there is no material present to be applied.WORKSTATIONS: -- End Trimming Unit: 0.38 kW - 12,000 RPM (x 2 motors) End Trim units with automatic 0° - 22° on horiz. plane from the machine control with (2) pre-set positions.When operating in conjunction with the corner rounding station the unit is equipped with two position pneumatics to leave the material long, thus allowing the corner rounding unit to have a seamless finish. -- T&B Trimming Unit:Top & Bottom flush trimming, 0.75 kW - 12,000 RPM (x2). Servo controlled, with large diameter vertical and horizontal copying devices with precise digital indicators.The unit is equipped with a servo driven motor to go from one material thickness to another from the controller. -- Corner Rounding Unit: 0.60 kW - 12,000 RPM (x2). The "ROUND-K" Unit is designed to work as an additional set of trimmers for rounding the top/bottom as well as the front/rear corners of work piece with 3mm P