LOBO CT508 STRAIGHT KNIFE PLANER20" x 8" Capacity, 5 HP single phase motor, 4-knife - 5,000 RPM cutterhead, 7" minimum part length, 1/4" maximum stock removal, manual bed height adjustment. -- 20" X 26" Bed dimensions. -- Feed speeds 16 /20 FPM -- Cutter head speed 5,000 RPM -- Chain drive feed rollers -- Solid chip breaker -- Extension rollers for longer stock. -- Complete with magnetic control, start/stop feed clutch, and dust hood.

Lobo 3-Head 43″ Wide Belt Sander (+ Flap/Brush Head)43" width cap, Drum, Drum, Combination HeadHead Configuration:1st Head: 9"; diameter grooved rubber-covered contact roll, with 20 HP – 1,760 RPM Motor.2nd Head: 9"; diameter grooved rubber-covered contact roll, with 15 HP – 1,760 RPM Motor.3rd Head: Combination Head with 6"; diameter grooved rubber-covered contact roll, smooth steel contact roll, with a 2″ air-inflated finishing platen, & 15 HP – 1,760 RPM Motor.Specifications -- All (3) heads have dial indicators for positioning PLUS a FOURTH dial indicator on the platen. The fourth head is a flap sander brush with a 3 HP motor -- Between heads one and two you will find hold-down shoes. Hold-down shoes control a workpiece as it passes through the sander, making it easier to run shorter parts through and prevent trailing edges and sniped or dubbed leading edges. -- Overall all capacity is 43″ wide X 5-5/8″ thick. -- Sanding Belt Dim. 43" X 75"Equipped with & Features: -- The feed mat, besides having 100% life, is 43″ wide and 7-1/2′ long. -- The feed motor is 3-1/2 HP and has variable speed from 5-45 FPM. -- The “FPC-515"; Touchpad Position Controller with LED Display for programmable thickness adjustment is in near flawless condition..

MURPHY-RODGERS MRZ 17/16L Interior/Open 6 Bag Dust Collector with Auger and Rotary Air Lock General specs: Approx. 7,600 CFM @ 8" SP. (6) top filter bags @ 24" dia. by 72" long. (6) bottom disposable plastic dust storage bags. -- Fan/Motor: 25 HP BALDOR TEFC motor direct driven fan with electrical starter. 17" diameter inlet, with lifting hooks. The bag collector motor is brand new and has never been powered on or fired up. -- Comes with: Main approx. 17" dia trunk line, shut-off, and Quick clamp removal for filter and plastic bags. -- All steel construction with rugged support legs. Air Deflectors allows operator to adjust the air flow and amount of waste evenly into the 6 waste bags. -- Note: NFPA 664 (Fire Code) states that a max. of 5,000 CFM is limit allowed for indoor enclosure-less dust collectors.

MURPHY-RODGERS MRJ-610-122 Pulse Jet Dust Collector with Rotary Air Lock and Transfer Fan.Specifications: -- 8,500 CFM approx. @ 9 to 1 air to cloth ratio baghouse dust collector with (60) 10-feet long filters; total cloth area of 943 sq. ft. -- Filter Cleaning: Continuous Self-cleaning Using Compressed Air. -- Main Fan: 30 HP top-mounted blower motor. with approx 18" dia. inlet. --System includes: Relay/Transfer fan, steel structure support stand, low height as waste is transferred by fan, safety ladder/platform, top safety railing, and approx. 16" Rotary Air Lock.Actual model is MRJ 610 -122.

MURPHY-RODGERS HEC-216-S/10 33,000 CFM Continuous Duty Automatic Self-Cleaning Pulse Jet Baghouse Dust Collector Equipped with: (216) 5" Dia. x 10' L Cloth filter bags for a total of 2,827 sq/ff. of filter area. (2) 42-1/2" W x 68" H & (2) 40-1/2" x 68" H Top access doors. (3) Front & (2) side 27" W x 54" H Filter access doors. (2) Square cone bottom hoppers, Each with, 25" x 25" Discharge openings. System utilizes (2) 4-1/2’ x 6’ x 4’ H Waste containers (NOT included). CHICAGO 100 HP - 1,780 RPM Roof-mounted blower, with 41” Dia. inlet. Motorized dampers for winter & summer modes. Winter mode: Directs air back into building, reducing heat loss. Summer mode: Directs air outside, cooling building. Electrical controls (as pictured). Complete with: Spare Filter Bags. NOTE: Installed Used in 2016 with "New" 100 HP motor, new bearings in blower & "New" spring mounts. NOTE: Variable Frequency Drive needs to be replaced. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

MURPHY-RODGERS - MRT-12 AS, ...Dust Collector (Interior) -- Specifications:Motor: TEFC 10HP, 230/460, 3 PH; Inlet diameter: 12"; Collection Outlet Opening: 11″; (1) Four (4) bag unit; 3,500 CFM. -- Floor space: 62" Wide x 102" deep x 118" high. -- NOTE: (4) Barrels (as pictured) are included!

MURPHY-RODGERS - MRSE-24: RAL Dust Collector; loaded with features. -- General Data: Self-contained baghouse, approx. 15,000 CFM with 1,913 sq./ ft. of filter area based on: 7.8 to one Air-to-Cloth-Ratio. -- Fan/Motor: 40 HP BALDOR motor; 22" dia. inlet; primary separator built into the unit; secondary separation of fine particles by filter bags. -- Equipped with: 16" Dia. bottom dump outlet controlled by a Rotary Air Lock with: Approx. 18" dia. discharge outlet. -- Complete with: (2) Electric motor driven automatic bag shakers; angle frame truck height support stand with walkway platform and full height ladder to access top of unit.Fan/motor mounted on top of the collector. -- Includes: Magnetic starter. control panel; silencer; explosion doors. -- Approx. dims.: 84" x 85" x 32' High; 6,100 Lbs.

7.5 HP TEFC BALDOR Motor, 2,960 CFM at 6" W.G., free-standing interior unit, designed for (6) filter bags mounted over two plastic waste bags or barrels for waste collection. -- 10" Inlet dia.; 128 sq. ft. filter area, 66 cu. ft. storage cap.; quick clamp barrel removal. -- It comes with barrels and bags as shown. -- Overall height is 129"; requires 26" x 108" floor space..Magnetic Starter included

NANXING NCG 2512L CNC FLAT TABLE MACHINE (W/LOADING/UNLOADING) + Auto Label Printing Application: -- Specifications:Bridge Gantry with 4' x 8' "Matrix" grid Phenolic surface table for "Nested Base Manufacturing", Automatic Loading and Unloading System with Vacuum cups & Sweeping Arm.Loading flow from Left to Right configuration. -- Work area:"Matrix" grid Phenolic surface flat table designed for "Nested Base Manufacturing". -- Working cap.:"X" Axis is 98.4" (2,500 mm), "Y" axis is 48" (1,220 mm) & "Z" axis is 9.8" (155 mm);Max. programmable speed: "X" & "Y" Axis 98 FPM (30 MPM), "Z" axis 65 FPM (20 MPM). -- Boring Unit:(10) Independent vertical boring spindles with (5) spindles in "X" axis & (5) spindles in "Y" axis, for 10 mm tools max dia. and 35 mm max. bore and 32 mm OC; -- Machining:(1) 12 HP (9 kW) Vertically mounted HSD electro-spindle router with HSK-63F adapters, Inverter controlled variable spindle speed up to 24,000 RPM, with max. torque from 12,000 RPM.(1) 8-Position Automatic tool changer with "revolver type" ATC tool plate. -- Operator & Machine Control: "SYNTEC" Controller, English language cutting/optimizing software, MS-Windows "10" based technology,32-bit Pentium - 400 MHz processor (w/operating system for Windows 7), 4 GB hard drive,15" Dell, international keyboard, soft-touch keypad & industrial mouse and USB port. -- Complete with:(2) 7.5 HP (5.5 kW) air-cooled vacuum pumps that provide 5,650 cu.ft./hr. (160 m3/hr.) of suction power: Safety & Emergency stops: Automatic lubrication system for guides & ball screw: Auto-Transformer for voltages between 200-600 V: -- Options Include: (1) NC Controlled infeed Scissor Lift table with vacuum loading Automatic Label Printing Station with Automatic Material Alignment (1) Rake system (1) NC controlled & powered flat belt outfeed table with vacuum sweeping system Tool Touch-Off Probe with automatic program update according to the tool length. Actual Model is NANXING NCG 2512L

NASH - 50-72: Spindle Sander -- (10) Spindles; 72" chucking. -- Cap., 3/8" - 6" dia. range; 2-1/4" dia. main arbor with long keys for driving head & tailstock wheels. -- Variable spindle speeds: 700 - 3,000 RPM; 7.5 HP spindle motor. -- 2 HP Feed & oscillation sanding rack motor; 60" max. sanding cap. with: (5) Sanding racks, self-adjusting and oscillating. -- Variable oscillating speed: (60 - 120) Strokes/Min; oscillating stroke adjustable up to 2" in length.Equipped with: -- Overhead mounted dust hood., -- Push-button control panel; production rate of (10 - 30) pieces/Min.

NASH 50-72 Spindle Sander(10) Spindles, 72" chucking cap., 3/8" - 6" dia. range;Specifications: -- 2-1/4" Dia. main arbor with long keys for driving head & tailstock wheels. -- Variable spindle speeds from 700 - 3,000 RPM, 7.5 HP spindle motor, 2 HP feed & oscillation rack motor, variable oscillating speed (60 - 120) strokes/Min, oscillating stroke adjustable up to 2" in length. -- (5) 72" Sanding racks, self-adjusting & oscillating. -- Equipped with: Overhead mounted dust hood, push-button control panel; production rate of (10 - 30) pieces/Min. -- Includes: brushes and sandpaper

NEDERMAN S-500 BAG HOUSE DUST COLLECTOR. -- Open Bag house designed for interior application; 5 HP TEFC material fan motor, 1,750 RPM; free standing 2,000 CFM open frame bag house, 162 sq. ft. of filter area via (16) beane material filter bags; 7.5" W.G. static pressure. -- Bottom discharge into (2) plastic waste collection bag. -- Includes: Side-mounted blower assembly with support legs; (2) quick disconnect clamps for the plastic bags. Starter motor with push buttons. Option:42 Gallons Drum Discharge, Single Drum (2 REQUIRED FOR COMPLETE S-500)

NEDERMAN S-750 BAG FILTER Dust Collector. The NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. With a 7.5 HP motor and a 4,500 CFM @ 6" WG it's the ideal solution for the small shop or single work-cell operation. -- Specifications: 7.5 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: 243 Sq/ft of filter media, easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 11". -- Available in 208/230 or 480 V, 60 Cy, 3 Ph. Must specify voltage at the time of orderAvailable options:42 Gallons Drum Discharge - Single Drum (3 REQUIRED)230 Gallon Dump Bin

NEDERMAN S-1000 BAG FILTER Dust Collector. The NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. It's the ideal solution for a smaller shop or single work-cell operation.Specifications: -- With a 10 HP motor and a 5,000 CFM @ 7" WG and 360 Sq/ft of filter media. -- 10 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: Easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 16". Available in 208/230/460 V, 60 Cy, 3 Ph. Must specify Voltage at time of orderAvailable option:- Aluminum Impeller: - 45 Gallon Drum Discharge - Single Drum (3 REQUIRED)- 230 Gallon Dump Bin: Available spare parts:- Filter Bag (24 Filters)- Plastic Bags (Roll of 90 - 8 mil thickness) - 500mm Clamp (bags, barrels, and bin)

NEDERMAN - S-1000: BAG FILTER Dust CollectorThe NEDERMAN S-Series Baghouse Dust Collector is: Quick to install and Easy to operate. It is the ideal solution for the small shop or single work-cell operation. -- Includes: 10 HP Motor; CFM range from 4,000 CFM @ 8" WG to 5,000 CFM @ 7" WG. -- Equipped with: 10 HP - 1,750 RPM TEFC Motor; (24) Beane material filter bags; (3) plastic waste collection bags; (3) clamps for easy removal of waste bags; magnetic starter. -- Features: 360 Sq/ft. of filter medial; easy installation, typically (1) hour; quiet operation. -- Inlet opening 15". (2) Units available!

NEDERMAN S-1000 BAG FILTER Dust Collector w/ Auto Bag ShakerThe NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. It's the ideal solution for a smaller shop or single work-cell operation.Specifications: -- With a 10 HP motor and a 5,000 CFM @ 7" WG and 360 Sq/ft of filter media. -- 10 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: Easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 16". Includes: -- Auto Bag ShakerAvailable in 208/230/460 V, 60 Cy, 3 Ph. Must specify Voltage at time of orderAvailable option:- Aluminum Impeller: - 45 Gallon Drum Discharge - Single Drum (3 REQUIRED)- 230 Gallon Dump Bin: Available spare parts:- Filter Bag (24 Filters)- Plastic Bags (Roll of 90 - 8 mil thickness) - 500mm Clamp (bags, barrels, and bin)

NEDERMAN S-750 BAG FILTER Dust Collector w/ Auto Bag ShakerThe NEDERMAN S-Series Baghouse Dust Collector is quick to install and easy to operate. With a 7.5 HP motor and a 4,500 CFM @ 6" WG it's the ideal solution for the small shop or single work-cell operation. -- Specifications: 7.5 HP - 1,750 RPM TEFC Motor, (24) Beane material filter bags and magnetic starter. -- Features: 243 Sq/ft of filter media, easy installation, typically (1) hour; quiet operation, (3) waste discharge points. Inlet opening 11". -- Available in 208/230 or 480 V, 60 Cy, 3 Ph. Must specify voltage at the time of orderIncludes: -- Auto Bag ShakerAvailable options:42 Gallons Drum Discharge - Single Drum (3 REQUIRED)230 Gallon Dump BinAvailable spare parts:- Filter Bag (24 Filters)- Plastic Bags (Roll of 90 - 8 mil thickness) - 500mm Clamp (bags, barrels, and bin)

NEWCNC - SMART ER SERIES I 510: CNC Router w/ATC & Lathe5' x 10' FLAT TABLE CNC ROUTER W/ATC & LATHE: Great for "Nested Base Manufacturing" or just about any type of 3-Axis work. -- Working Table: 63" (1,600 mm) x 122" (3,100 mm). There are: (4) Pop-Up stops to aid in panel positioning; an "M-code" controlled 4-zone electrovalve; special high flow Vacuum Table System. -- X- & Y-Axis Speed: 3,181 IPM (265 FPM / 83 MPM) & Z-axis: 350 IPM (29 FPM / 12 MPM) for quick traverse positioning that reduces total CNC machining time between cutting cycles. "YASKAWA" Servo drives power the axes movement. -- Industrial machine tool welded structurally engineered: Machine base provides a solid foundation for superior cut quality; entire frame is stress relieved and heat treated. -- Moving gantry bridge: Travels on: "THK" Large thick hardened & precision ground rectangle linear guide slider-ways giving extra smooth movement for high-speed traverse & accurate cutting. -- Tool Gantry & Bridge Movement: Large thick inclined teeth rack & pinion; vertical axis travels on a large diameter precision ball screw for smooth consistent movement. -- Machining: (1) 12.6 HP (9.4 kW) Air-cooled SCM Router spindle with: "HSK 63F" Adaptor; variable programming speeds: From 1,000 to 22,000 RPM. -- Tools are loaded into the "SCM" spindle by: (1) 8-position plate "on the fly" ride along carousel ATC (automatic tool changer). -- Tool heights can be set using the Tool Length setting gauge (included); machine requires ER-32 tool collets. -- CNC Control: Industrial Grade "OSAI 10/510" OPEN CNC control with: 19" Color monitor; includes self-diagnosis & alarm history display & background editing; up to (4) simultaneously controlled axes with 3D simulation; helical interpolation; tool offset; length compensation & backlash compensation. -- Compatible with virtually all CAD/CAM programming software on the market; you choose the software that best suits your needs. -- Includes: (1) 7.5 HP (5 kW) "Rotary Vane" type Vacuum Pump. -- Complete with: Dust hood with 6" manifold connection; Tool Length setting gauge; "MPG" handheld wheel remote; safety bumper system on both sides of the moving bridge & a safety bar around the back of the machine. -- Options Include: (1) 12' Lathe attachment with: Chuck and tailstock (...$ 8,450 value); (1) additional 7.5 HP (5 kW) Rotary Vane Vacuum Pump (...$5,150 value).

NEWCNC SMART ER SERIES II 510 CNC ROUTER W/ATC & BORING:5' x 10' FLAT TABLE CNC ROUTER W/ATC & BORING is great for "Nested Base Manufacturing" or just about any type of 3-Axis work. -- Working Table: 63" (1,600 mm) x 122" (3,100 mm). There are (4) pop-up stops to aid in panel positioning & a "M-code" controlled 4-zone electro valve, special high flow vacuum table system. -- X- & Y-Axis speed are 3,181 IPM (265 FPM / 83 MPM) and Z-axis is 350 IPM (29 FPM / 12 MPM) for quick traverse positioning that reduces total CNC machining time between cutting cycles. "YASKAWA" servo drives power the axes movement. -- Industrial machine tool welded structurally engineered machine base provides a solid foundation for superior cut quality, the entire frame is stress relieved and heat treated. -- The moving gantry bridge travels on "THK" large thick hardened & precision ground rectangle linear guide slider-ways giving extra smooth movement for high speed traverse and accurate cutting. -- Tool gantry & bridge movement by large thick inclined teeth rack & pinion; the vertical axis travels on a large dia precision ball screw for smooth consistent movement. -- Machining: (1) 12.6 HP (9.4 kW) Air cooled SCM Router spindle with HSK 63F adaptor, variable programming speeds from 1,000 to 22,000 RPM. -- Tools are loaded into the "SCM" spindle by (1) 8-position plate "on the fly" ride along carousel ATC (automatic tool changer). -- Tool heights can be set using the Tool Length setting gauge (included); machine requires ER-32 tool collets. -- CNC Control: Industrial grade "OSAI 10/510" OPEN CNC control with 19" color monitor; includes self-diagnosis & alarm history display & background editing; up to (4) simultaneously controlled axes with 3D simulation, helical interpolation, tool offset, length compensation & backlash compensation. -- Compatible with virtually all CAD/CAM programming software on the market; You choose the software that best suits your needs. -- Includes: (1) 7.5 HP (5 kW) "Rotary Vane" type vacuum pump. -- Complete with: Dust hood with 6" manifold connection; Tool Length setting gauge; "MPG" hand held wheel remote; Safety bumper system on both sides of the moving bridge & a safety bar around the back of the machine. -- Options Include: (1) 10-Spindle Vertical Boring Block with 5 independent spindles in "X" axis & 5 independent spindles in "Y" axis ($8,450.00 value). (1) Additional 7.5 (5 kW) rotary vane vacuum pump ($5,150.00. value).

NEWMAN/Cameron - KF-24: Dip Chain Gang Rip Saw with CAMERON "34H-M1" Infeed SystemSpecifications -- Saw Arbor: 24" Arbor cap.; 14" max. dia. tooling; 4" max. motorized thickness adjustment;22" min. length for glue joint accuracy; 6" throat. -- 2-13/16" Dia. arbor; 24-1/2" capacity saw sleeve arranged for 3-1/8" dia. bore saw blades; saw blade options: 10" - 14" Dia.; spacers: 4-5/8" dia. includes: (1) Saw sleeve and spacers. -- 75 HP - 3,600 RPM TEFC Direct drive motor; arbor with: Disc brake & load meter; arbor lockout on the access door. Feed & Chain: -- 5 HP Variable feed speed: 20 to 100 FPM with: Jam arbor protection. Dip bed carried on: 5" Pitch hardened Double-V chain; hardened dip cams; extruded structural aluminum feed bed slats with: Replaceable steel-backed rubber insert strips; automatic chain oiler with low level shutoff. -- (2) 4" Dia. air loaded overhead pressure rolls; spring-loaded overhead bed plate; pressure rolls & bed plate unit with motorized adjustment; slide type infeed guide with: Handle block; either side of the guide can be used for a stock engraver. -- Anti-kickback finger system with: (1) Lower & (2) upper on infeed; (1) upper kickback on outfeed. Equipped with & Features: Upper outfeed main dust hood: 7-7/8" Dia. 2,150 CFM Infeed dust hood 4-7/8 dia. (855 CFM). (1) Spare sleeve; (2) setup fixtures; generous array of spacers (see photos).