Equipment For Sale
10580 Results Found
Call for Price
Call for Price
Mereen Johnson 424 DC/SR4 Gang Rip Saw with Automated Infeed with multiple lasers manufacturer’s specs to be confirmed 24” width capacity 3-1/2” thickness capacity 75 HP main motor 3 hp feed motor feed rete 30-245 fpm
Call for Price
$ 47,500
MEREEN-JOHNSON 424 DC GANG RIP SAW 24 inch width capacity 75 HP arbor motor- 3600 RPM direct drive 5 HP variable speed feed ( new belt ) Four ( 4 ) kick-back finger sets : ( Two ( 2 ) top in-feed, One ( 1 ) bottom in-feed, One ( 1 ) top out-feed ) A new out-board arbor bearing assembly New set of alum bars and rubber slats installed It is wired 480 volts 3 phase . The serial no. is MJ-4709 One saw sleeve and set of spacers ( 6 saw blades ) Cleaned, painted, and checked.
Call for Price
Call for Price
The seller has confirmed that this Mereen Johnson 441 Rip saw is in great working/running cnodition and it is ready to load! - 2004 Cameron Auto Opti-Rip Infeed - Model: 34F-M1 - Serial: OR164 - 100% Servo (only Servo is this Cameron) - Full amp load 81 - 44" W bed - Up to 20 saws can be run on the arbor - No moving blades BUT there are moving lasers Although this one has been pulled from service, they have an identical one still running and available for inspection....
Call for Price
Mereen-Johnson Model 441-DC Gang Rip Saw Capacity: Arbor space 41” Arbor Drive: 75 HP 3600 RPM TEFC motor Feed Drive: HP TEFC variable speed direct; 45’ to 225’ feet per minute Hold Downs & Bed Plate: Four 5” dia. Air loaded high yield idle press rolls Saw Sleeve: One 41” capacity sleeve Dust Collection: Four upper dust pick-ups: two (2) 8” dia., two(2) 4” dia., one lower 4”dia. Pick-up:(requires total 4820 CFM @ 5,000 feet per minute) Swing Arm & Tip-Up Cart: One floor mounted dual shaft swing arm and one tip-up saw sleeve set-up cart Electrical: Arranged for 3 phase, 60 cycle, 460V Cameron Automated Opti-Rip Model #34F-M1 System: Manufacture Year: (2004) Complete with length measurement Tally System 5 infeed belt and chains for feeding a Gang Rip saw up to 41” wide 16 width sensors 3 sets of pinch rolls for short stock 1 fixed & 4 movable laser lights This system feed for 4’ to 16’ max lumber length It feeds from operator right to left Wired 220V; If 440V required, a transformer will be needed
$ 91,000
2013 Merlo P40. 17 Reach forklift with 308 hrs. Maximum lifting capacity of 8,800 pounds. It has a maximum lift height of 55' and a maximum reach of 41'. Load capacity at maximum lift height of 5,500 pounds and a load capacity at maximum forward reach of 1100 pounds. Operating Weight 22,928.1lb Length To Fork Face 19.02ft in Ground Clearance 1.58ft in Width Over Tires 7.88ft in Overall Height 8.24ft in Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.
Call for Price
Call for Price
Call for Price
Call for Price
Call for Price
Call for Price
Call for Price
Call for Price
Whole Log Metal Detector with MDI Sensor 28" Belt Will Pass Up to 21" Diameter Logs If Sensor is Raised will Pass 26" Diameter Logs
Call for Price
Call for Price
$ 550,000
Lumber Breakdown, Dual Grading, Trim, Sort, and Stack System – 45’ (4) strand package deck w/ S-drive & H-78 chain, 6’ (4) arm breakdown hoist (hydraulic w/ HPU) w/ stick removal belt & stick stacker, dual grading stations as follows: (1) top (5) strand common shaft dual drive & (1) bottom w/ (5) strand decline table 20’ grading w/ operator control w/ 81X chain, both w/ operator control w/ 81X chain, Softac software & PLC VASKAWA57 VFD, Lucidyne label jet printer, MIC lumber trimmer w/ double paddle fence, MIC (28) bay bin sorter, (5) arm blade type lumber stacker & Sullivan Palatek air compressor (piston),Specifications: 386' long x 24' high, runs 6' - 16' L longer, thickness 1" - 4" thickness, width 6' wide packs, 3 1/2 - 22" wide packs, 3 1/2 - 22" wide, Loaded on your truck, all controls are in order ,this system was running December 1, 2023, ref #171 – For More Details Call for Complete Component System