Woodworking Equipment For Sale

FLETCHER FM-2000 Contour EdgebanderSpecifications: 0.4 mm to 2 mm Banding thickness, up to 2" panel thickness, Unit to run strip veneer, coil, rolls of PVC, melamine, or wood veneer. Large overhead glue pot with a quick heat time of 10 minutes. Equipped with: -- Programmable temperature control with safety interlock so that applicator does not run until proper operating temperature is reached. -- 1-3/4" silicone-coated drive roll. -- Foot pedal-controlled tape advance. -- Foot pedal emergency stop. Optional Equipment: -- Power-Feed $ 2,618.00 -- 3° Manual Tilting Table $ 809.00 -- 45° Tilting Table $ 5,382.00 -- Push Button Powered Operated Tilt Table $ 6,232.00 -- Outboard Stock Support $ 1,565.00 -- 3MM Capable $ 2,950.00 -- 4"; Thickness Capacity $ 10,000.00

Forestor 900. Owned 10 years. Last used about 2 years ago. No power. Used to split round posts. Takes a 4 x 6 and makes a 2 x 6. Call 800-459-2148 for more info.

FORMOSA - RSN-12, ...Straight Line Rip Saw w/Laser LightSpecifications: -- Saw dia.: 14". --Saw kerf: 3.2 - 5.0 mm. -- Max thickness: 2" -- Max. process width: Left of saw blade 250 mm; Right of saw blade 500 mm. -- Min length: 200 mm -- 3,450 RPM. -- Feed Speed: 39 or 26 MPM. -- Main motor: 7.5 HP. -- Feed motor: 1 HP. -- Machine dim.: L 1,950 mm x W 1,280 mm x H 830 mm. -- Weight: 950 kG.Equipped with Laser Light.

Fortis Heavy Duty sliding table shaper, 4 speeds, 2 spindles, with air cylinder. Very nice machine $4,500 - Call 218-638-2810 or 218-410-0548

FRAMA - TC-1500, ...Hydraulic Copy Lathe.Hydraulic Copy Lathe with (3) different speeds during execution of the work. Possibility of manual or automatic configuration on (3) intensities: 1) Regular working speed, 2) slow working speed for difficult points reproduction, and 3) fast speed to eliminate nonproductive points. Technical Data. -- Main drive motor: 6 HP. -- Hydraulic pumping unit: 2 HP motor. -- Max. turning dia.: 300 mm (12"). -- Distance between center: 1,500 mm (59"). -- Max. cross-slide speed: 9.5 MPM (30 FPM). -- Carriage return speed: 11 MPM (36 FPM). -- Copying device stroke 75 mm (3"). -- Max. hydraulic pressure between cones: 20 kG/CBM. -- Headstock taper: MT 4. -- (8) Turning speeds: 1,000 - 1,250 - 1,750 - 2,000 - 2,250 - 2,500 - 3,500 - 4,500 RPM. Also included : -- Knife Grinder: 1 HP motor.

FRAVOL SMART S600-23 Edgebander w/Pre-Mill & Corner Rounding:Main Specifications: -- Edge & Workpiece Capacity: 0.4 - 8 mm (0.016 - 0.315") edge; 10 - 60 mm (0.394 - 2.362") panel thickness; -- 140 mm (5.512") min. panel length and 100 mm (3.937") min. panel width. -- Feed-speed, 14 or 18 MPM (46 or 59 FPM.)Front-End Equipped With: -- Pre-Milling Station (RT/S), (2) motors @ 1.1 KW (1.5 HP), 12.000 RPM, LH & RH rotation w/pneumatic programmable jump control for chip-free and clean panel edges. Standard equipped with Dia. 60 mm x 64 mm H, with diamond inserts. -- IR Panel Heat Lamp: Improves gluing bond especially during cooler ambient temperatures and humid conditions. -- Automatic Edge magazine: For strips up to 8 mm & coil stock up to 3 mm thick PVC. -- Duo Gluing System: For regular granulate Hot Melt (EVA) and easy conversion to PUR glue. "Teflon lined" glue tank with bi-directional glue roller. Automatic temperature reduction during stand-by time. Glue tank has quick release system for maintenance or quick change to a different color or glue type. -- Side Pressure Section: (3) Pressure rollers, (1) motorized, (2) idle, pneumatic pressure control and programmable NC-positioning servo motor.Work-stations: -- End Trimming (INT 2/S): (2) motor @ 0.50 KW (0.70 HP) 12,000 RPM, automatic pneumatic chamfer 0° - 15° or total exclusion from control panel. Glides 45° on prismatic linear hardened steel guides. -- Trimming Unit (RF-S/S): Top/Bottom flush/bevel/radius milling unit, (2) motors, 0.73 KW (1.00 HP) 12,000 RPM. Pneumatic remote tilt in (2) positions, postion-1 for radius and thin edges up to 0.8 mm trimming, position-2 for flush trimming up to 8 mm edges.Equipped with banding thickness gauge block feature for quick and easy set-up/changeover. Includes 1-axis NC servo control motors for programmable change-over from thin to 8 mm solid wood edges or incremental re-positioning of the cutter head. -- Corner Rounding Unit (SYNCRO 1): Compact and easy to set up for leading & trailing edges, (1) motor 0.22 KW (0.295 HP) 12.000 RPM, electronically synchronized. Working capacity, min. 10 mm, max. 60 mm panel thickness. -- Profile Scraping Unit (RB/S): Top & bottom radius scraping for PVC - ABS edges. Heavy construction to eliminate vibrations and guarantee superior edge quality. Air blow-off jets and chip collection box. -- Clean Spray System: Top/Bottom spray nozzles applies edge cleaning solvent prior to buffing. -- Glue Scraping Unit (RC/S): Top & bottom pneumatically operated glue scraping on flat panel surface to remove potential glue squeeze-out that otherwise would coat the cloth buffing discs. -- Buffing Station (GSI/S): Top/bottom (2) motors, 0.09 KW (0.125 HP) 2,800 RPM, manual, horizontal, vertical and tilting adjustment -- Hot Air Unit PHON (GP/S): Top/bottom hot air blowers to restore PVC color after scraping. Electrical power 2,000 Watt, 0° to 600° C temperature adjustment.Complete With:• PLC Program Control, with 10.7" col

FRAVOL VSR TOP & BOTTOM TRIMMERSpecifications: -- Edgebanding thickness 0.4 mm to 3 mm, 16 mm (0.62") to 60 mm (2.36") panel thickness capacity. The rough trimming function uses vertical copy pads and one disc copier between the two cutters in a horizontal position, allowing 0.4 mm to 3mm radius edge rough trimming without replacing the cutters. Panel working height (thickness) is from 16 mm to 60 mm.Equipped with & Features: -- Two 12,000 RPM motors complete with braze welded hard metal cutters Ø 50x16- Z6. Your choice of profiles R1; R2; R3; 5°; 30°. -- The machine comes with a new, patented worktable that provides smooth panel sliding and extremely flexible edging without using jigs. -- Sliding on nylon blocks allows perfect cleaning of the panel melamine surfaces.

FRAVOL - VSR, ...Top & Bottom TrimmerSpecifications: -- Edgebanding thickness: 0.4 mm to 3 mm; 16 mm (0.62") to 60 mm (2.36") panel thickness capacity. Rough trimming function uses vertical copy pads and (1) disc copier between the (2) cutters in a horizontal position; allows 0.4 mm - 3 mm radius edge rough trimming without replacing the cutters. - Panel working height (thickness):16 mm - 60 mm.Equipped with & Features: -- (2) 12,000 RPM Motors with: Braze welded hard metal cutters; Ø 50 x 16 - Z6. - Choice of profiles: R1, R2, R3; 5°; 30°. -- Machine with: New, patented worktable that provides smooth panel sliding and extremely flexible edging without using jigs. -- Sliding on nylon blocks allows perfect cleaning of the panel melamine surfaces.

FRUILMAC RANDOMAT E - End Matcher; --For End Matching flooring or cabinet & entry door rails; the feed-thru system allows continuous feeding of random length parts with any kind of profile.Capacity & Description: -- Width cap. 1-3/16" x 9-7/8'; length cap. 6-5/16" x 137" length (longer lengths with additional support); 3/8" min. - 1-3/16" max. thickness cap. --÷ Approx. (10) cycles/Min depending on part length & width; -- Feed system with (2) 120" long x 10" wide powered infeed & outfeed belt conveyors, parts are automatically fed & positioned with sensors. -- Positive stop to the 1st vertical shaper head (a 2nd shaper head is next to the 1st one); cope cycle is automatic. -- Parts are conveyed past the 1st & 2nd shaper head, automatically reversed and positioned to a positive stop for the 2nd cut on the other end of the part. At the same time the 1st shaper head would be coping the 1st end of another part.Equipped with: --÷ Twin 7.5 HP - 7,500 RPM high-speed shaper motors which pneumatically traverse in tandem for each cutting cycle. --÷ Cutting station with overhead hold-down wheels and 4-point pneumatic clamping with (2) overhead & (2) horizontal clamps. --Controller & Operator Interface: Key Pad SIEMENS Controller, PLC controlled conveyor & shaper cut cycle for automatic operation, variable feed speed conveyor line, and shaper head advance with LED readout on the controls. --Includes Infeed and Outfeed Conveyors

FRIULMAC - Dual-Feed, ...Double End Cut-Off SawFor squaring workpieces and for transportation to a Planer or Moulder with a straightening table.Specifications: -- 79" Max. (2,000 mm) opening from Saw to Saw. Motorized opening with LED readout on the control panel; left-hand fixed with left-hand fence line. -- Hopper Magazine - material capacity: Min. length: 7.87" (200 mm), max.: 79" (2,000 mm); width: 1-1/8" (30 mm) to 6-3/4" (170 mm); and thickness: 0.59" (15 mm) min. up to 2-3/8" (60 mm) max.; hopper stack height: 23-1/2" (600 mm).Each side is equipped with: -- (2) Trim saw motors, 5.36 HP each; saw blade dia. 9.84" (250 mm). -- Hydraulic feed drive unit: 4 HP (3 kW) motor. -- Trimming & throughput capacity: Up to (55) pieces/Min.NOTE: Voltage transformer for 600 Volts available with the machine

FRIULMAC Quadramat Single End TenonerSingle end tenoner with (4) heads with Jump cope, cope, disc sanding and disc sandingSpecifications: -- Workpiece Length: 125 - 1500mm -- Workpiece Width: 125-1500mm -- Workpiece Thickness: 13 - 40mm -- Configuration: Jump-Cope, Cope, Wheel-Sanding, Wheel-Sanding -- First Station: 7.4 HP Jump-Cope/Profiling Unit with 40mm Diameter Shaft, 6000 RPM Rotation -- Second Station: 7.4 HP Cope/Profiling with 40mm Diameter Shaft, 6000 RPM Rotation -- Thirds Station: 4.7 HP Sanding Wheel -- Fourth Station: 4.7 HP Sanding Wheel -- Variable Speed Control of Sanding Stations from 750 - 1400 RPM -- Feed Speed: 13 - 98 FPM

FRUILMAC RANDOMAT-E End Matcher;For end-matching flooring or cabinet & entry door rails; the feed-thru system allows continuous feeding of random-length parts with any kind of profile.Specifications: -- Width cap. of 1-3/16" to 9-7/8"; length cap. of 6-5/16" x 137" length (longer lengths with additional support); 3/8" min. - 1-3/16" max. thickness capacity. -- Approx. (10) cycles/Min depending on part length & width; -- Feed system with (2) 120" long x 10" wide powered infeed & outfeed belt conveyors, parts are automatically fed & positioned with sensors, and a positive stop to the 1st vertical shaper head (a 2nd shaper head is next to the 1st one); cope cycle is automatic. -- Parts are conveyed past the 1st & 2nd shaper head, automatically reversed, and positioned to a positive stop for the 2nd cut on the other end of the part. At the same time, the 1st shaper head would be coping the 1st end of another part.Equipped with: -- Twin 7.5 HP - 7,500 RPM high-speed shaper motors, which pneumatically traverse in tandem for each cutting cycle. -- Touch-screen SIEMENS Controller, PLC controlled conveyor & shaper cut cycle for automatic operation. -- Variable feed speed conveyor line; shaper head advance with led readout on the controls. -- Cutting station with overhead holddown wheels and 4-point pneumatic clamping with (2) overhead & (2) horizontal clamps.Includes:(4) set of used tooling

- End Matcher for the Continuous Feeding of Random Length Work Pieces - Minimum Working Length: 160mm (6.3") - Working Width: 30-250mm (1.18"-9.84") - Working Thickness: 10-30mm (0.39"-1.18") - Two 7-1/2 HP, 3ph Profiling Motors - Spindle Speeds: 6,800 RPM - Spindle Diameters: 40mm - Cutterhead Feed Motor: 1 HP - Two 1-1/2 HP Motors for Infeed/Outfeed Conveyors - Infeed/Outfeed Conveyor Sizes: 123" x 11" - Sound/Safety Enclosure - New in 2004 - Current Voltage: 460V

The Friulmac Randomat/SQ End Matcher has a Length Capacity 14" to 120" Width Capacity 2" to 10" Thickness Capacity .32" to 1" Feed speed 4 to 30 M/min Feed motor 15HP Scoring motors 4HP with 30mm diameter shaft, 7600 RPM Trim/Hogging motor 7.5HP with 40mm diameter shaft, 6000 RPM Profiling unit J-33 - 7.5HP with 40mm shaft, 6000 RPM Profiling unit J32 - 10HP with 40mm diameter shaft, 6000 RPM

Sanding wheel shaper for the production of profiles on the sanding wheels. -- Template carrier holds metal or plexiglass template (same as can be used on the moulder knives). -- Spindle length 5" with 1" diameter arbor for wheel support. Handles 8" diameter wheels (3) included with the machine. -- X and Y axis on dovetail slide with lineal bearing support for smooth movement during the wheel grinding. Pneumatic clamping on grinding wheels. Depth of grinding 1.5" for raised panel. -- Tilt capabilities from 0 to + 30°. -- Grinds all types of varda wheels on 1 HP motor with speed of 1,750 RPM. --You can customize this machine to you needs.

G & P - EPN, ... Pump Sander (Double-Sided), -- Double-end direct-drive pneumatic Drum Sander. -- 2 HP Motor - 3,600 RPM motor speed. -- (2) 1-1/4" Dia. x 10" long shafts.

GABBIANI GT 2 115 38/38 REAR LOAD AUTOMATIC PANEL SAW: -- Specifications:Working capacity 149.6" (3,800 mm) Rip & Cross-cut pull-back. Main saw blade projection is 4.5" (115 mm).30 HP (22.4 kW) Inverter driven, variable RPM main motor & 3 HP (2.2 kW) scoring motor. Automatic exclusion of scoring unit. Pneumatic quick-change system for blades -- Saw carriage: Feed speed from 3 - 492 FPM (1 - 150 MPM), return speed of 492 FPM (150 MPM.Automatic cutting stack height & length limiter adjusts according to the program dimensions. Automatic saw carriage lubrication. -- Pusher Fence: 0 - 230 FPM (0 - 70 MPM) Forward positioning speed, 230 FPM (70 MPM) return speed.Rack & pinion movement on both sides to assure the pusher remains parallel. (8) Total Material gripper clamps, with (4) of the grippers in the cross-cut section independent & programmable according to the cutting pattern.All gripper clamps open to 4.5" (115 mm); -- Operator Interface:PC Front-end controller with SCM "MaestroCUT" + Windows operating system.21" LCD "Touch Screen" monitor display with real-time graphics + function control keypad. Virtually unlimited program storage via USB ports; RS-232 serial port, keyboard, mouse.Maestro software features machine functions, programming, run time, diagnostics, production reports, imports, language and unit of measurement, optimization cut software (Maestro Pattern)Maestro Cut 3D editor: Label printing software, 3D simulator, graphic editor, panels editor, cutting editor for figured panels, semi-automatic macro.Easy Import: This software imports from an Excel file all data related to part of a cutting list previously selected by the user to Maestro Pattern, Diagnostic for errors or machine malfunction by means of an error signal code, incremental or absolute programming in mm or inches. All enclosed in an air-conditioned control cabinet. -- Rear Lift Table:4-Post screw type powered rear load lift table 149.6" x 63" (3,800 x 1,600 mm); max stack height 23.62" (600 mm) without a pit or risers; -- Complete with: Automatic Side alignment device. Min. part width 2.36", Max. part width 149". Automatic saw blade height adjustment. "Quick-change" blade system. (4) Air support tables 78" x 24" (1,981 x 609 mm), with (1) common blower. -- Options Include:Zebra label printer. Powered Rear In-Feed conveyor with fork cutouts. -- Actual Model is GABBIANI GT2 115 38/38

Gabbiani Double End Tenoner Available approx August 1, 2023 Can also be paired with a direct transfer to a [Homag DET](https://www.carolinamachinerysales.com/listings/4073344-used-2006-homag-fl20-double-end-tenoner) at the same site.

25 Spindles 10 Dowel inserters 2 Dowel hoppers Glue tank Water tank Left and right adjustable fences 4 Pneumatic clamps foot pedal controlControl Panel

Gannomat Pro-Line 50 • Row of holes as well as line drilling in the SYSTEM 32 mm • 50 (2 x 25) holes in one drilling cycle