Woodworking Equipment For Sale

CAM-WOOD BR-2732X Boring Machine27-Spindle boring head on 32 mm centers with position indicator.Features & Specifications: -- Stops in 0° & 90° with pneumatically assisted positioning in vertical & horizontal. -- 0" - 3" Adjustable drilling depth with speed control. -- Head height fine adjustment with mechanical digital readout. -- (2) 2 HP - 3,400 RPM Motors. -- Cast iron 45" x 19-1/4" table with side fences for mirror-image. -- Line boring fence with repeat stops. -- Foot actuated pneumatic clamps & drill cycle.Complete with: -- Magnetic starter, overload protection. -- Optional quick-change chucks $28.00 ea.

CAM-WOOD BR-3532X CONSTRUCTION BORING MACHINE35-Spindle boring head on 32 mm centers with position indicator.Features & Specifications: -- Stops in 0° & 90° with pneumatically assisted positioning in vertical & horizontal. -- 0" - 3" Adjustable drilling depth with speed control. -- Head height fine adjustment with mechanical digital readout. -- (2) 2 HP - 3,400 RPM Motors. -- Cast iron 52" x 19-1/4" table with side fences for mirror-image. -- Line boring fence with repeat stops. -- Foot actuated pneumatic clamps & drill cycle.Complete with: -- Magnetic starter, overload protection. -- Optional quick-change chucks $28.00 ea.

CAM-WOOD BR-2132 Boring Machine21-Spindle boring head on 32 mm centers with position indicator.Features & Specifications: -- Stops in 0° & 90° with pneumatically assisted positioning in vertical & horizontal. -- 0" - 3" Adjustable drilling depth with speed control. -- Head height fine adjustment with mechanical digital readout. -- 2 HP - 3,400 RPM Motor. -- Cast iron 37-1/2" x 19-1/4" table with side fences for mirror-image. -- Line boring fence with repeat stops. -- Foot actuated pneumatic clamps & drill cycle.Complete with: -- Magnetic starter, overload protection. -- Optional quick-change chucks $28.00 ea.

Heavy Double Head Line Borer with (2) 21-spindle heads; 32 mm spindle spacing.Specifications: -- Drilling from the bottom up and with 5-1/2" - 23-1/2" distance between rows. -- Drilling vertically from the bottom allows the chips to drop down falling out of the holes. -- Drilling depth of up to 3" max., takes only seconds to set. -- (2) 2 HP - 3,400 RPM motors; spindles with steel gears & high quality bearings. -- Easy repetition by (2) air index pins for continuous line drilling, left and right roller track supports extend up to 400 mm (15-3/4") for larger panels.Features and Includes: -- 120" Back fence with (4) repeat "flip" stops; includes 27-3/4" (704 mm) fence for quick positioning of flip stops. -- (6) Pneumatic holddowns to automatically actuate when the drill cycle begins. -- (42) "Quick Change" chucks for easy tool change. -- Magnetic motor controls and 1/4" air regulator with filter and oiler; 100 PSI required air pressure.

CAM-WOOD CC-388PA Clamp Carrier (8 Sections)8-Section Pneumatic Clamp Carrier with 98" length capacity.Equipped with: -- (6) Heavy Duty zinc plated clamps per section (48 clamps total). -- 40" Opening on clamps. -- Jaw sizes of clamps are 3-1/2" with inward draft. -- Pneumatic overhead panel flattener. -- Pneumatic clamp tightener and 1/2 HP electric motor rotation.Standard features: -- Large I-beam frame & legs for max. rigidity and durability. -- Heavy-duty zinc-plated clamp with huge 3/4" diameter jack bolt for super strength. -- Powerful caterpillar chain drive for clamp rotation. -- Select switch control for auto or manual mode.Includes: -- Clamp tightener with pneumatic wrench for rapid tightening and loosening of clamp. -- Pneumatic panel flattener to hold panels flat while clamps are tightened.Versatile and reliable Edge Gluing Machine for Solid Wood gluing, including laminate board, parquet, flat stock, table top, core block, truck flooring, turnings, chair seat, legs, spindle blanks, stair tread, and many others.

This is a two year old system. The seller changed their machinery footprint and no longer needed. This system is meant to package material to bring to another line, not for shipping. Designed to nest/stack/pack up to 36” in height This system consists of the following components (1) Cameron Automation Scoop lifter system for material up to 6” in width Dual length measurement sensors Cameron Automation Computer (1) Cameron Automation Plywood Kicker (1) Cameron Automation Plywood Belt Driven Roller Conveyor Produces bundles up to 15” wide x 36” high Includes the big bundle nester option General specifications: Flooring lengths from 8” to 8’6” Flooring widths from 1½” to 6” Flooring thickness from 3/8” to 1” Pack width: up to 46” Production capabilities: 55 lineal feed per minute Capable of (36) 7’ bundles per hour 5,000 sq. ft. per shift Semi-automatic infeed approximately 31’ long Singulator Operating voltage: 440v, 3PH

Cameron Automation Flooring Nesting Line Buffer Table for making 2'-10' flooring into nested bundles. Makes a new bundle every 30 seconds. Feeds from right to left

CANTEK - C 12 RSH, ...Straight Line Rip Saw:Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", saw arbor speed 4,400 RPM. -- 16 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", -- Distance from column to center of chain 18". -- Table size is 39" x 57", table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickel chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond-cut surface for positive material feeding.

CANTEK - C 12 RSH, ...Straight Line Rip SawRuggedly constructed with cast iron & ground tables; cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12"; saw arbor dia. 1"; saw arbor speed 4,400 RPM. -- 15 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", distance from column to center of chain 18". -- Table size is 39" x 57"; table height 31-1/2". Features: -- The cast iron upper-pressure housing provides a stable mounting for the precision ground & Nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond cut surface for positive material feeding.Approx. (600) Hours production time.Total amperage is 21.5 amp and the gross weight is approx. 2,530 Lbs.

CANTEK - C 12 RSH, ...Straight Line Rip SawRuggedly constructed with cast iron & ground tables; cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12"; saw arbor dia. 1"; saw arbor speed 4,400 RPM. -- 15 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", distance from column to center of chain 18". -- Table size is 39" x 57"; table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & Nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. --:1-Piece cast iron chain with a diamond cut surface for positive material feeding.Total amperage is 21.5 and the gross weight approx. 2,530 Lbs.

CANTEK C-12RSH Overcutting Straight Line Rip Saw;Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (8) holddown rollers and solid welded steel base chassis.Specifications: -- 3.35" Max. thickness cap; 8" min. length; variable feed speeds from 50 to 120 FPM and powered by a 1 HP feed motor. -- 1" Dia. saw arbor powered by 15 HP arbor motor; swings 8" thru 12" dia. blade at 4,500 RPM; with 18" distance from blade to saw column. -- Arbor runs in precision angular contact type ball bearings (eliminates any radial run-out & axial thrust) - V Belt driven from below. -- 31-7/8" From floor to top of table; table is 39" wide x 57" long. -- Rigid machine body consists of a thick welded steel frame with an integral table which is fitted with a sturdy cast column. Feed & Chain: -- 1-Piece cast iron chain with a diamond cut surface for positive material feeding and absolute straight line feeding. -- Precision caterpillar chain and double "VEE" guide rails are made of special cast iron. -- Equipped with high-frequency hardened chain Guide Rails. -- The chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Hold-down rolls for increased control and precise straight line cutting (6 rows).Features: -- Easy to access adjustments and controls. -- Mechanical operation Chain Oiler (Best) provides consistent lubrication to the chain track and automatically adjusts to your feed speed. -- Equipped with: (3) Sets of anti-kickback fingers; (2) top and (1) set in the table. -- (1) 5" dia. dust outlet. -- Soft start, Star Delta starter - Telemechanique-Square D, Magnetic Wye/Delta Starters - Low Amperage Soft-Starter on the arbor motor - Electrics to UL/CSA Standards.Available Options when order with machine: --20mW Laser (FPIMLC1320W) & Laser Holder (FPICAN03) – made in N.A.... $ 495.00 -- KANEFUSA 12" Glue Joint Carbide Rip Saw Blade...$ 165.00

CANTEK - C14RS, ...Straight Line Rip SawSpecifications: --Overcutting Rip Saw. -- 4.92" Max. thickness cap; 8" min. length. -- Variable feed speeds from 49 to 128 FPM and powered by a 2 HP feed motor. -- 1-1/2" Dia. saw arbor powered by 15 HP arbor motor. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long. Equipped with & Features: -- (3) Rows of antikickback fingers: (2) Top & (1) Bottom, for safe operation. -- (8) Holddown rolls for increased control and precise straight line cutting (6 rows). -- 6" (150 mm) Wide chain track runs on double-V guide rails, which are made of special cast iron for added wear. -- Magnetic Controls.

CANTEK MODEL CFS100 / EM-12 DEFECT SAW AND END-MATCHING SYSTEM:Consisting of a CANTEK model "CFS-100" Optimizing Cut-Off Saw followed by a CANTEK Model "EM 12" Through-Feed End Matcher and with the following specifications and features: CANTEK "CFS-100" OPTIMIZING CUT-OFF SAW -- Up to 20 mm X 200 mm or 100 mm X 100 mm( 3/4" X 7.87" or 3.9" X 3.9" cutting capacity with 18" x 30 mm bore sawblade is driven by a 10 HP motor driving the saw spindle at 3,200 RPM; 2.7 HP servo drive feed system drives the stock up to 260 FPM; 0.787" min. distance between crayon marks; requires 75 to 80 PSI at the saw and 100 to 120 PSI at defect blow-off station. Machine comes completely wired and programmed. -- Machine is ideal for separating crayon marked waste zones from useable material before entering into a feed-thru End Matcher; provides (3) times greater production than manual cut-off saws.5% + Material recovery (yield increase) over manual cutting; compact and user-friendly design; controller adopts an industrial grade computer that employs a 32-bit floating-point DSP system and features flash and battery backup SRAM for double security; superior to conventional PC-based controls, it can fully eliminate the machine going down or being damaged due to a poor environment, such as, unstable voltage, high temperature, sawdust, etc. -- With defect blow-off system combined with computerized logic control permits the blow-off time and the length of defect to be set as desired; provides efficient defect removal and eliminates defects from bumping against the sawblade, resulting in the machine going down or sawblade damage. -- Computer control provides easy and fast maintenance; feed system driven by a servo motor for fast and accurate motion and position control; max. feed speed up to 260 FPM; cutting rate up to 80 cuts per minute with cutting accuracy within approx. ±1mm / 0.40"; control employs a touch screen for easy learning and operation.Features: -- New machine design features maximum maintenance convenience; high quality electric components provide maximum dependability; safety guards for maximum operator protection; 48" long infeed table standard - longer available option; 18" carbide blade included.(5) Cutting modes include: -- Adjustable end cuts to a max. of 10mm (0.4") -- Fixed length of cutting mode. -- Sequential cutting mode with (10) sets of cutting sizes held in memory (for sequential cutting mode only). -- Cutting on fluorescent marks with double-end trimming (perfect solution for end matching). -- Reading fluorescent marks with double end trim, fixed-length, random length end match, and finger joint block cutting. CANTEK "EM-12" END MATCHER -- Continuous through-feed system; handles random length min. 10.6" to any length x 0.4" to 1.38" thickness x 12" width capacity; -- 295 FPM max. feed speed; average speed of 75 FPM based on 6'-6" board lengths; with 118" infeed and 98" outfeed tables; -- 5.5 HP Shaper motors, 1 HP feed motor an

CANTEK EM-12 End Matcher;1.6" to 12" Width x 0.4" to 1.38" thickness (to 2-1/4" optional) x 10.6" min. length capacity. Unlimited lengths possible.Specifications: -- Feed speeds to 295 FPM with approximate production speeds of 77 FPM (based on 6-1/2' incoming boards). -- Standard 173" long infeed table and standard 86" (2,200 mm) long outfeed table; -- (2) 10 HP cutterhead motors with 40 mm spindle diameters; 1 HP feed motor; 1/2 HP motor drive to cutterhead carriage; clamping pressure from top and side; 24 volt DC controls.Standard equipment and Features: -- Designed for machining tongue & groove with or without V's on flooring and panel products; designed to be used for finger joint cutting. -- Heavy-duty self supporting main frame; compact design requires minimum floor space.Feedworks: -- Capable of processing material as short as 11" to an unlimited length; variable speed through-feed systems is controlled by frequency inverter; through-feed system allows the tongue to be cut simultaneously on the tail of one board and the leading edge of the next board. -- Powered top Urethane rolls and spring loaded bed rollers feed the material into position for processing. -- Pneumatic side pressure ensures the material is held square against the fence.Complete with: -- Safety and noise reduction enclosure; convenient touch screen control is used to quickly activate and adjust the machine functions. -- Powered 176" long infeed conveyor is included (additional length optional); with a 86.6" long outfeed table (additional length optional). -- Includes: (2) Individual Precision Insert Tooling Heads as Supplied with Machine & stacked to make (1) pair of heads; set of heads provided for groove on left and tongue on right.

CANTEK - GOODSPEED CP-1250 AP Hydraulic Copy Lathe. -- General Data: 44" Length cap. with 4" min. length of stock and 1/2" - 4" max. diameter cap., hopper feed with automatic chucking, square or round stock can be hopper fed. -- Equipped with: 7.5 HP Spindle motor, 1,800 - 3,200 RPM spindle speed adjustable by pulley change, 3 HP hydraulic motor. -- Complete with: Swivel control panel, PLC sequence controller built into separate control cabinet, (3) pressure gauges, automatic way & support collar lubrication & safety wire mesh across the front of machine. -- Includes: Two hydraulic copiers (rough + fine). Travelling steady rest and installed knives. -- Production capacity: Approx. (5 - 7) pieces/Min for 600 mm length, (3 - 5) pcs./Min for 900 mm length, (2 - 3) pcs./Min for 1,200 mm length, depending on cutting speed, type of material, etc. -- Electrical load: 11.4 amps, 10.5 HP @ 575/3/60.volts.

CANTEK JF-330A Profile Knife Grinder Clamping length of 12" (300mm) for both straight and profile grind; dia. of knife swing 12" (300mm). Grinding arbor: 3 HP grinding motor with VFD (LED Readout) drive from 1500 to 4200 RPM. Quick change removable (140mm) wheel adapter. Machine set for axial constant grinding and template set up on right hand side. Over the wheel precision diamond dresser assembly for dressing and dimensioning of wheel. Manual positioning: of grinding wheel to tool; positioning of back clearance angle and side clearance angle 5°/10°/15°. Quick change stylus turret for applications. (6) included with machine. Carriage: SCHNEEBERGER lineal bearing table movement. Table movement 12" x 6". Coolant system: 1/8 HP motor from coolant pump located in tank below. (3) coolant nozzles for smooth flow of coolant to knife rest during grinding. Additional hose with nozzle for cleanup. Stainless steel splash guards throughout!Option included: Motorized Side Clearance – including set left and set right Motorized Wheel Back Clearance Angle Motorized Grinding Wheel In/Out

CANTEK - C 12 RS, ...Straight Line Rip Saw:Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", saw arbor speed 4,400 RPM. -- 16 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", -- Distance from column to center of chain 18". -- Table size is 39" x 57", table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickel chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond-cut surface for positive material feeding.

CANTEK MX-370P EDGEBANDER (W/ PRE-MILL & CORNER ROUNDING): --Specifications:0.4 - 3 mm Edge thickness, panel thickness 0.315" - 1.77". Minimum panel length 6.7", minimum panel width 3-¾". Heated infeed fence for better glue adhesion. Fixed feed speed 29 FPM.Equipped with: -- Pre-mill (2) 1.5 kW each (12,000 RPM) counter-rotating cutter-heads for removing up to 3mm of the panel edge. -- Quick change 1.2 kg Teflon-coated glue pot is designed for EVA hot-melt glue. The glue pot is a Quick-Change type and can be removed and replaced in less than 1 minute. -- Guillotine shear: The guillotine shear can rough trim coiled material up to 3 mm in thickness. Pressure rollers section consist of one large driven roller, followed by a smaller one. Workstations: -- End Trim: The end trim system is a single motor with (2) saw blades. The unit is mounted on high-precision linear guide rails. -- Top & bottom trimmers with (2) high-frequency motors for top & bottom trimming of the panel. Each motor has an inset knife cutter-head which can be adjusted from flush to beveled finish for thin edges, and radius trimming (2 mm radius). Single motor Corner Rounding Unit Can process between 0.4 - 3 mm and up to a board thickness of 1.77" (45 mm). The multifunctional cutter can round straight or radius edges with a 2 mm radius cutter. -- Radius scraping unit fine-tunes the edge radius while removing knife marks during the milling process on radius edging. Insert knives have a 2 mm radius. -- Buffing unit leaves a super finish on ABS and PVC edging and removes any discoloration on the edges.

CANTEK MX350 EDGEBANDER (W/ PRE-MILLING): -- Specifications:0.4-3 mm Edge thickness, panel thickness 8~45 mm, min. panel width 100 mm (4″), min. panel length 170 mm (6.7″). Equipped with: -- Quick melt Teflon coated glue pot 2.5 Lb capacity. Two spring loaded pressure rollers (One driven, one idling). Automatic coil feed PVC/ABS up to 3mm thick, pneumatically operated guillotine. Laminate strip material can be hand-fed. PLC control system with LED display and keypadWorkstations: -- Pre-Mill station with (2) 1.1 Kw 12,000 RPM trim motors 32 mm (1.25") max. material thickness. -- Single motor front and rear edge trim station. -- Top & bottom trim station with insert knife cutters for radius trimming & bevel trimming. -- Top & bottom scrape station 2 mm radius. -- Top & bottom buffing. -- Feed speed 29 FPM

CANTEK LBS300-5S 3-Sided Moulding Sander5-Head Brush Sander, 11" width and 4" height cap., for 3-sided sanding of linear profiled material. Head Configuration: -- (2) Sets of Top abrasive brushing heads with variable speed adjustment by inverter, 0.75 HP (0.55 kW) motor each. -- (1) Left side head, adjustable up/down, in/out, and can be set on an angle, 0.5 HP (0.37 kW) motor. -- (1) Right side sanding head which can be adjusted up/down and in/out, 0.5 HP (0.37 kW) motor. -- (1) Left side sanding head is adjustable up/down, in/out, and can be set on an angle, 0.5 HP (0.37 kW) motor. -- Brush head spindle speed adjustable from 200 - 1,200 RPM. -- Variable feed speed of 6.5 - 27 FPM, adjustment by frequency inverter.Features & Specifications: -- Min. workpiece length 26", min. workpiece thickness 3/8". -- 0.25 HP (0.18 kW) Conveyor motor, 0.33 HP (0.25 kW) moving brush head motor. -- Depending on the application, brushing heads can be cleaning brushes or abrasive cloth brushes. The dovetail pocket design allows for easy abrasive/brush replacement. -- Centralized control panel for operator convenience integrated into machine base.Also available in 460V, 3-Ph, 60 Cy (factory order only – app 10-12 weeks)