Equipment For Sale

KUFO UFO-105DC Cartridge Dust Collector. (4) Upper cartridge filter, (4) Bottom bags, 7.5 HP motor, 4,900 CFM. -- Equipped with: Bottom mounted 5-manifold inlet branch with (5) 4" inlets connect to a 8-1/2" dia. inlet. -- Push button starter mounted to base with (4) swivel casters. -- Upper cartridges 19-1/2" x 39-1/2", filler material 1 micron Polyester. Bottom bags 19-1/2 x 31" plastic bags (4) ea. -- Unit is pre-wired 220 V.

KUFO UFO-104D Dust Collector4-Bag self-contained free-standing unit (4 up & 4 down, all cloth), 23-3/4" dia. bags. -- Features: 4,167 CFM, 10 HP Motor. -- Bottom mounted 6-manifold inlet branch with (6) 4" inlets connect to a 9.5" dia. inlet; available as option: manifold with (5) 5" dia. inlets. -- Complete with: (4) Upper filter bags 2.5 micron and (4) lower cloth collector bags 2.5 micron, lower collector bags have 21 cu. ft. storage cap. each (84 cu. ft. total) -- Equipped with: Push button starter, base is mounted on (4) swivel casters.

Kuka KR60-3 Robot System KR C4 Control System Kuka Programming Smart Pad Robot Enclosure (3) Heave duty conveyor racks

KUNDIG DUPLEX 53-RC-E Wide Belt Sander (2) Heads; 52" Width cap. Drum, Combination Head.Head Configuration1st Head: 7-1/4" Dia. rubber covered contact roll, 25 HP motor.2nd Head: Combination head with rubber covered contact roll and segmented finishing platen, infeed sensors sense the panel and electronically control the platen height with timers, variable edge control can also be set, 20 HP motor.Specifications: Abrasive belt size 54" x 75" with air tensioning and electronic abrasive belt tracking, both heads with abrasive grit thickness adjustment, 2 HP Variable feed drive. -- Conveyor belt speeds 9 - 45 FPM, controlled by electronic inverter & adjustable on the control panel; infeed & outfeed rubber covered holddown rollers.Equipped with & Features: -- Workpiece thickness cap. 1/8" - 6-1/4", motorized thickness adjustment with LED readout. -- A joystick controls the conveyor opening and start/stop of the feed, automatic "over-thickness" protection and automatic conveyor belt tracking. -- Constant passline of conveyor height at 35". -- Air blow off of second head abrasive belt. -- Emergency stop button, motor load meters, magnetic controls.NOTE from the seller: There is a small leak in the air bladder . The sander has 6,541 working hours

Max. operating width in grain direction approx. 3200 mm Min. operating width in grain direction approx. 600 mm Width of the veneer strips across the grain from approx. 60 mm Veneer thickness approx. 0.3 – 2.5 mm Capacity up to 28 joints/min. Feed speed approx. 30 m/min. Operating voltage 480 V, 3 Ph, 60 cycles

L & L 400HP Belt Driven DensifierSpecifications: -- Main motor: 400 HP -- Densifier tank thickness: 3/4" Wall -- Tank dimensions: 50" Dia. x 48"Equipped with: -- Funnel-top lid with interlocked limit switch -- Heavy-Duty operator platform with stairway -- Soft Start -- Infeed Conveyor -- Mezzanine -- Was used to process PE film scrapNOTE: Unit has seen very little use.

LM Bump Rollcase Package Saw Includes waste conveyor under saw and elevated conveyor 550v/3 phase Approx 55" Bar Already dismantled and ready to load, as shown in the last two photos.

2003 | Honda Engine | Needs Carburetor Work

Model: HMPC-7-24 | Cuts up to 20' bundles | Hydraulic Controls | Laser to indicate cut | 35' Waste Conveyor System

L & M Verticut 2000 Saw bars, LM unit saw bars Overall length 68”+- 5 bars available Used Saw chains available Contact us for a delivered price

2016 | Model# 200MP-7-SS | Honda Engine | Ran when taken out of service

Model: HMPC-7-24 | 2003 | Voltage: 600V | Extra Bar and 5 Chains Included

LA NUOVA SCOLPITRICE 201-16 Multi-Spindle Carving Machine.(16) Cutter Stations, 55" max. workpiece length,Specifications: -- (16) Dual carving spindle heads, 8" between spindles, 20" max. working diameter. -- Each head has a roughing & finishing spindle, all heads swivel 360° with pneumatic locking. -- Upper carriage controlled by (2) High Frequency changers allowing (2) motor speeds of 12,000 & 18,000 RPM. -- Pneumatic chucking of material, stock turns 360°. Copy stylus of hardened and ground steel, adjustable for depth on either side. -- Traverse feed of carving heads was patented and requires no maintenance. -- Includes: Lot of tooling. Table for flat/horizontal copying.Note: Machine completely gone over and all heads rebuilt in 2011 and used sparingly since.Actual model is 201-16.

V2000 60 x96TS-1VL-ONS-OCE-06PS Transportation Simulator Performs both rotary and vertical motions Designed for testing larger crates up to 60-in. by 96-in

LACEY-HARMER E-LINE Self-contained Visible Diode Laser End ShooterEconomical self-contained Visible Diode Laser; optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° - +40° C operating temperature, 90 V for 250 nano-Sec mechanical stock. Beam angle with 5 mW - 15 mW output, 636 nm wave length. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed -- Projects a line from approx. 12' to 15' depending on area lighting -- Consisting of two parts; (1) crossbar style mounting bracket, please add...$ 143; (2) axis slide brackets for easy positioning, add...$ 125 each or alteratively a simple universal stationary mounting bracket add...$ 30.

LACEY-HARMER LD-2002 Diode LaserEconomical self-contained Visable Diode Laser, optics housed in a sealed cell to provide added protection against contaminants and moisture; nickel plated housing. -- Specifications: 100 Millampere operating current, -20° to +40° C operating temperature, 90 V for 250 nano-sec surge protection. Beam angle 5 to 90 degrees, 5mW to 35mW output, 636 nm wave length for lines up to 20' projection. -- Options: 36" Long Diode Array Stand adjustable up to 90° from mounting surface, lines move easily and parallel to each other, micro-adjustment to make lines parallel, no tools needed. -- Optional items consist of: Crossbar style mounting bracket, please add...$ 90; axis slide brackets for easy positioning, add...$ 125 or alteratively a simple universal stationary mounting bracket, please add...$ 30.

1- 5mm Boring and Inserting Unit with Vibratory Hopper 1-8mm Boring and Inserting Unit with Vibratory Hopper Power: 208v-220v, 3 Phase, 30 Amps 96? Maximum Work Zone 4 zone stops 3-Axis Control For Positioning Weight 6,000lbs Solid One-Piece Welded Tubular Steel Frame Footprint (L x W x H): 135? x 45? x 82? Shipping Dimensions (L x W x H): 42.3? x 49? x 43? Shipping Weight: 7500 lbs

Hot Air Edgebander for Preglued banding 0.4 - 1.5 mm thickness Automatic cutoff for up to 1/32" Coil feed with manual feed for strips Panel thickness 10-50mm Front and rear end trim Top/bottom trim

Laguna Bandt 4 Edgebander Machine is 6 months old Extremely low hours - Buyer upgraded to a larger machine!

Gantry Clearance: 12? Z Axis Travel: 13? Table Size: 4’x8' Working Area: 49?x97? Rapid Speed: 1,800 IPM Cutting Speed: 1,000 IPM Spindle HP: 12HP Spindle Speed: 6,000 – 24,000 RPM Cutting Time: 50 Hours Electrical: 208-230V/ 3PH Equipped With: 12 HP HSD Spindle 8 Position ISO 30 ATC Yaskawa AC Servos Drive Motors 6 Zone Vacuum Table Planetary Gear Box Drive System Tooling Kit Helical Rack & Pinion X/Y Axis Ball Screw Z Axis 10 HP Stock Regenerative Blower Vacuum Pump Syntec Industrial Control System Controller: B+R PP65 Stepper Package Footprint: 78?x127? Approx. Shipping Weight: 3,500 Lbs