Equipment For Sale

Nye High-Rollout Bucket, heavy duty design, extra dump height for loading high trucks. Nye builds standard replacement buckets as well as specialized buckets to suit our customers' demands. Models include Hot Slag buckets, High-Rollout Buckets, Heavy Duty Loader Buckets (HD Buckets), General Purpose Buckets, (GP Buckets), Tire Buckets, Scrap Aluminum Buckets, Stump Buckets, Demolition Buckets, Garbage Buckets, and loader buckets with clamps.

Nye Stump Harvester

Nyle Kiln L300 - L300 Nyle high temperature Lumber drying Kiln - 240v single phase. Capable of temps up to 160 degrees. - Bought new in 1999 Call 800-459-2148 for more info.

350 Pallets / 6-8 Cords | 480V | 2023 | BTUh 800,000 | Dimensions 40' L x 8' W x 9' 6" H Drying Time: Summer - Drying: 2 - 3 Days / Heat Treating: 2 - 4 Hours Winter - Drying: 3 - 5 Days / Heat Treating: 3 - 6 Hours

Nyle PHT350 Kiln System was powered up and tested, but not put into production.

Nyle Firewood Dry kiln No chamber included

OAKLEY H-5 Double Sided Edge Sander. -- General Specs: With 7.5 HP -1,800 RPM TEFC motor; (2) 8-1/2" x 57-1/2" Cast Iron platens; 8" x 164" abrasive belt, 4,680 FPM belt speed. -- Equipped with: One 11" x 62" Cast iron side table on one side and (1) 19" x 64" cast table on the other side, (1) cast iron radius tilting end table, end table tilts 0 ° - 45°; 6" vertical table travel w/hand wheel adjustment. -- Features: Rubber covered direct drive pulley and idler pulley,Complete with: Magnetic starter with overload protection, (8) dead head radius ends with graphite covering, and (1) steel covered spare head roll.

Oakley Edge Sander

OGAM Gang Rip 30HP Motor w/electrical still Hooked Up, Model PO 195, S/N 15149

OGAM - PO-340, ...Dip Chain Gang Rip Saw Specifications: -- 75 HP TEFC Motor, dip chain feed with overhead arbor. -- 4.3"; x 13.3"; Cut capacity. -- 16" Max. blade diameter. -- Power rise and fall. -- 70 mm dia. arbor. -- 2 HP Variable feed speed up to 115 FPM.Equipped with & Features: -- Automatic chain oiler. -- (3) Sets antikickback fingers. -- Adjustable infeed fence. -- Motor load meter. -- Many new saw blades.

OGAM MODEL PO-340 DIP CHAIN GANG RIPSAW ( THis is a Parts machine only )Specifications: -- 60 HP arbor motor, dip chain feed with overhead arbor, 13-3/8" (340 mm) max. rip cap. (between saw blades), 12-5/8" chain width. -- 9-13/16" Mn. to 13-7/8" max. blade dia., 4-3/4" max. depth of cut (manual raise and lower of the spindle), 70 mm dia. arbor runs @ 4,200 RPM; min. board length 19-3/4" (without short stock feed plate-see photo). -- Variable speed belted feed motor 20 to 100 FPM (approximate).Note From Seller: Ogam Gang Rip Saw. 60 HP motor 230/460. I don’t know much about this machine. Bought it used but haven’t been able to hook it up due to our current electrical service. The person I bought it from says it ran well when taken out of service. Can load on a truck.

OGAM PO/M Straight Line Rip Saw;Specifications: -- 20 HP Main motor. -- 24"; throat capacity. -- Max. cutting height: with 12" blade 3", with 16" blade 4". -- Min. diameter of circular saw blades: 8". -- Max. dia. of circular saw blades: 16". -- Min. length of working pieces: 10". -- Variable feed speed from 50 -154 Ft./minute. -- Feeding belt width: 11". -- Spindle Speed: 4,500 RPM. -- 36"; x 60"; table.Equipped with & Features: -- Fence and rail system with one stop. -- Infeed table row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Top row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Split hold down steel smooth roller around blade. -- Split hold down steel smooth roller around blade. -- Steel smooth top hold down roller. -- Chain is in excellent condition!

Ogden SL3660 RFS

30 brand new Oleson 10" double cut band blades. Entire lot for $20,000.00. Individual blade $1,175.00. Buyer pays for shipping. Call 800-459-2148 for more info.

OLIVER 5385 Single Head Wide Belt SANDER (37") 1-Head and 37" belt width Combination Sanding Head with rubber covered contact roll and adjustable finishing platen, 1/8" - 5" Thickness capacity, 36" width capacity.Specifications: -- 20 HP Main drive motor. -- 1 HP Variable speed (15 to 45 FPM). -- 1/4 HP Power raising and lowering conveyor bed motor. -- 37" X 75"; Abrasive belts for longer life and less loading.Features; -- Central control panel features digital thickness set-up control for accurate stock height and removal. -- Four post lift design assures accurate consistent results. -- Oscillating belt is controlled by an air sensor to prevent sanding lines. -- Finishing Platen is fully adjustable and can be removed. -- Multiple dust ports for efficient dust management. -- Independent motors run the sanding belt, feed conveyor, and table elevation for maximum power to each operation.

OLIVER 5390 Dual Head Wide Belt Sander1/8" to 6" Thickness capacity 36" Width capacity.Equipped with: -- 20 HP main drive motor, 2 HP variable conveyor feed 15 to 49 FPM.Head configuration: -- 1st Head: Contact drum -- 2nd Head: Roller and PlatenFeatures: -- Digital thickness controller w/ thousandth's jog feature. -- Omron electronic eye sanding belt tracking. -- Variable speed drive 15 to 49 FPM -- Power raising and lowering of the conveyor with digital thickness set-upSpecification: -- Max. width cap 36" -- Feed motor 2 HP -- Elevation motor 0.5 HP -- Max. thickness 6" -- Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 4.75" dia. with 2" wide finishing Platen -- CFM requirements 3600 -- Feed speeds 15 - 49 FPM -- Belt size 37" x 60".

Oliver 144 Jointer, no fence Call 800-459-2148 for more info.

OLIVER 4430 20" PLANER WITH HELICAL HEAD20" Maximum stock width cap., 1/4" to 8" max. stock thickness, 10" minimum stock length. Equipped with: -- 5 HP Main drive motor and mechanical raising and lowering of the cutter head. -- Fixed bed height of 29-7/8". Table dimensions 20"L X 21"W. Overall all table dimensions with infeed and outfeed bed extensions 51"L X 21"W. -- 3-1/4" Dia. Helical Cutter Head with 4-sided carbide inserts. -- Auto-Depth lock via nitrogen-charged cylinders eliminates snipping. -- 8" Max. thickness adjustment via handwheel includes LED Digital readout for head positioning. -- 4-Post support for proper head alignment.Complete with: -- 5" Dust outlet and built-in mobile base for ease of movement

OLIVER 4470 25" Straight Knife Planer Full 24" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through the 4-knife standard cutter head, this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor. --OPTIONAL EQUIPMENT: Byrd Shelix Cutterhead (ADD $2,400)

OLIVER 4470 25" Shelix Cutterhead Planer; 10 HP motor Single Phase, or 15 HP 3-Phase motor. Full 25" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through , Byrd Shelix Cutterhead this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor.