Equipment For Sale

Toyota Model 42-5FG25 Forklift Sideshift

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i4t TOYOTA 7FDU45 9,150 Lb. Cap. Diesel Forklift Truck, with 8,895 Hours (As of 10/16/24) & Side Shift Specifications: Max. lift height 179", Lift speed 95 FPM. Turning radius 9.03', Right angle stack 10.9'. Equipped with: 2-Stage Mast, with Back tilt 6°, 5-3/4” x 44” x 27-1/2” H Forks, Max. fork centers 58", Side Shift, & Mast guard. TOYOTA "13Z" Diesel engine. 8.35-15-15 Dual pneumatic front & 7.00-12/5.00 Solid rear tires. Overhead guard, with Rated vertical impact 32,000 Ft.-Lbs. & Headlights.

Toyota 7000 Capacity Forklift

TOYOTA 7FGCU25 Cushion ForkliftSpecifications: -- Load Capacity: 5000 lbs -- Power: 53 HP -- Power Measured: @ 2400rpm -- Fuel Type: Gas/LPG -- Tire Type: cushion -- Max Speed: 10.6 MPH -- Overall Height - Mast Lowered: 6.73’ -- Right Angle Stack: 7.86’ -- Turning Radius: 6.46’ -- Mast Load Center: 24";Lift Speed: 118 FPMEquipped with: -- Sideshifter -- 4-Wheel Sit Down

Trace Machine Pallet 4 Stringer Nailer w/Stacker & 56in X 11ft 6in Pallet Rollout

Self-propelled track carrier Self-powered slasher Radio remote control No hydraulics or electrics Reguired

Trackside Mfg Stretch Wrapping Machine 31"x10' infeed and outfeed, 24" belt, no power

1988 Trail Mobile Flatbed 48' Spread axle Rebuilt frame New air ride New hardwood deck Lights good Brakes good Aluminum rims Low pro 22.5 tires (need replaced soon)

2009/2010 53' x 102" Transcraft Conestoga (Curtain Side)Flatbed VIN# 1TT F532S x A 1088115 Merlott Vango Tarp.

2012 Transcraft 48' aluminum flatbed trailer w/air ride VIN 1TTF-482C9D3756763

1999 TRANSPORT 5 AXLE LOG PUP AIR RIDE 24' BED

2013 5 AXLE LOG PUP TRAILER 24' DECK ALUMINUM STAKES SUPER SINGLES 445/50R22.5

TRAVAINI TRO 501-1A-200V "40 HP VACUUM PUMP (LIQUID RING) 11,969 Hours:40 HP Travaini liquid ring, single stage vacuum pump "TRSC 100-700/C/F". Nominal capacity 500 ACFM @ 20" HgV; max Vacuum 27" HgV. -- Pump materials:Include cast iron housing, ductile iron impeller, and stainless steel shaft. Shaft seals are carbon face with viton elastomers. -- 40 HP:200 Volt, 3-Phase, 60 Hz, TEFC monoblock assembly for direct drive, no field alignment needed. -- Sealing fluid re-circulating system includesReservoir of carbon steel with fluid level gauge and drain, high-efficiency discharge separator and oversized heat exchanger. -- High temp switchTo protect against over-temp operation. -- Suction line accessories includeInlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve, and vacuum relief valve. -- Heat exchangerIs an air cooler type made from aluminum and extended surface fins. -- Electrical controls include:Starter/overload reset, pump running light, hour meter, hi-temp light, and terminal blocks, all mounted in a NEMA 12 cabinet.

2006 Trelan 23 -No blow by and doesn't use oil -New hood jack -New cylinder -10 sets of new blades -Extra set of belts -Disk pockets are in good shape

1988 Trelan Model 18 Whole Tree Chipper Equipped with Detroit 518 Diesel Engine, Engine Hours Unknown, New Drive Chain and New Belt, New Tire, No Separator Ready for the Woods... Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

1989 Trelan 23 Chipper -9000 frame hours -Rebuilt C-27 CAT with 200 hours on engine -New tires -New outrigger piston -Rewired corded remote -New wireless remote -New hoses -New intakes -New bearings in the PTO -Engine Preheater -New Auto-feed system NEEDS PAINT BUT WILL GO STRAIGHT TO WORK!!!

(4) -710/50/30.5 Trelleborg 428 forestry tires with rims $8,000 OBO

2012 Tremzac 824 shavings mill Call 800-459-2148 for more info.

TREMZAC 4284500 Twin Arbor Shaving Mill -- Hopper capacity 42" X 84" -- (2) 75 HP Electrical motor (included) -- Stationary unit with conveyor. -- Handles logs 5" - 22" in diameter and 84" lenght. -- Capacity (shaving) 125 to 500 cubic feet/Hour. -- Hopper Magazine: 42" Wide x 84" long -- Adjustable platen for different shaving thickness. -- Cutterhead 42" wide with (8) knives -- Hopper with hydraulic motor and variable feed speed.Also included: -- Set Up Stand -- (2) spare shaving cutter head

Tri State Machinery Straight Line Rip Saw S/N 4.5.74-72