Equipment For Sale

SFVG1200 twin vertical Band Saw 1200mm wheel blade size. Machine used for the log break down process in continuous flow sawmill layouts. Capacity to process logs up to 500mm in diameter and 3.000mm long. This machine is fitted with main motor, motor drive panel, servo motor thickness selection, adjustable saw guides, slabs pneumatic side pressers, special chain and hydropneumatic tensioning system to tension the Band saw. - Wheel blade width: 6”; - Minimum log Length: 1200mm; - Standard maximum log length: 3000mm - Minimum diameter: 120mm; - Maximum log diameter: 500mm; - Saw cut width: 70 to 300mm; - 4 set of pneumatic side pressing rollers for side boards; - Motor size: 2 x 75CV 4P 50hz (INCLUDED) - Drive Panel Included; - Central chain motor size: 7,5 HP 4P; - Linear Cutting speed: 30m/s; - Feed speed capacity: 48m/min; - Saw Blades are not included. - Infeed conveyor length: 4.000 mm included; - Outfeed conveyor length: 6.000 mm included; - Machine width: 5.000 mm; - Machine overall Length: 12.000mm - Servo motor thickness setting system (INCLUDED); - Approximate weight: 15.000 kg;

This is a Horizontal Band Saw Resaw Machine with Two saw heads. This is an ideal Machine for the recovery line, as it processes the slabs coming out of the Vertical Twin band saw machine “the resaw process”. It comes with an input chain conveyor, driven press rollers. Cutting Height and saw blade tensioning setting system. It also comes with main motor, motor drive panel, the Frequency inverter, gear motor drive panel. It does not include the saw blade. - Wheel blade: Ø1000mm; - Wheel blade width: 5"; - Maximum wood width: 400 mm; - Maximum wood height: 380 mm; - Minimum length of wood: 1250 mm; - Single Input table/ conveyor width: 600 mm; - Motor press roller: 1 cv 4P (2x); - With two independent infeed rollers; - Forward speed: 45-50m / min for small logs; - Main motor indicated: 2 x 60 hp - Soft starter Drive panel: included; - Servo motor thickness setting system (INCLUDED); - Main transmission belt: 3 x Channel B; Length: 6.532mm; - Width: 2.220mm; - Weight: 7655kg.

Vance PT600R8 Drum Chipper See this machine at IWF Atlanta 2024! This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

Weeke BHP 007/430 CNC Router 13 HP HSK 63F Spindle with air blast nozzles 8 Position Rack Style ATC 7 Spindle Boring Block 4x8 Table Part location pins (2) Becker 7 HP vacuum pumps Woodwop Light Barrier safety system

The Vantec 2800mm Spindleless Veneer Lathe is designed to process veneer for plywood production from both hard and soft logs. Its metal tempered grooved rollers and lathe knife inclination system work perfectly to make sure there will always be a precise contact area between the lathe knife and the log during the peeling process by eliminating vibration that could cause damage to the Veneer sheets. Vantec Spindleless lathe proves its efficiency by delivering consistent thickness variation and a impressive top linear speed of 180 m/ min throughout the peeling process for face or core veneers with smooth surfaces. - Log diameter up to 600 mm; - Max log length: 2750 mm; - Min log Length: 2300mm; (with stacker) - Min log length:1800mm (no stacker); - Veneer thickness: 1.0 to 4.0 mm; (Pine and eucalyptus); - Log core after peeling: 40 to 45mm; - Maximum linear speed 180 m/min; - Drive panel included; - Each motor is individually connected by a Variable Speed Drive for torque control in two points of traction on the rollers to pre- vent excessive load on tip ends; - Log Central aligner with maximum of 2200 mm of movement; - Pneumatic scriber Knives (02 fitted on the sides to cut in width and 01 in the Center to cut the length); - Width: 7640 mm; - Length: 3400 mm; - Height: 2550 mm; - Approximate weight: 14000 kg.

This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

Equipment designed for debarking/rounding of logs for veneer production. This debarker is capable of processing logs from 120mm to 735mm diameter. It is fitted with metal tempered grooved rollers to press/rotate the log against the lathe knife. The log carriage moves on skates and linear guides through hydraulic cylinders. It has a rack and pinion system that ensures the alignment of the carriage. It also comes with the drive panel, but it does not come with lathe knife. Maximum Diameter capacity (logs with • bark): 735 mm; Maximum diameter for de- • barked/rounded logs: 600mm; Minimum diameter for de- barked/rounded logs: 120mm; Max. log length: 2.800mm; Min. log length: 1.800mm; Rail Skids: 65 model; Rollers gear motor: GD (helical gears); Approximate weight: 9.000 kg; Power consumption: 35HP, Power of the rollers: 50cv 4p (5cv + 20cv); Cylinder diameter: 50mm; Lead Lime: 270 days Hydraulic unit: 210 l; Motor unit: 10 hp 4p; Hydraulic pump: 60 l / min; Width: 7.000 mm; Length: 2.840 mm; Height: 3.100 mm;

The Vantec Veneer Auto Stacker, ELV 1.82B is a Vacuum stacker for 2800 mm Veneer lathe. It is fitted with double stacking system (04 bins), with four veneer transport lines and four 5hp exhausters. with of two stoppers and eight ejecting arms. With drive Panel, VSD for exhaust fans and hydraulics lifting tables. Min veneer sheet length sheet: 2300 mm; • Max veneer sheet length sheet: 2700 mm (or Two sheets of 1350mm); • Min veneer sheet width: 800 mm; • Max veneer sheet width: 1500 mm; • Max height of stacks: 1000 mm; • Exhaust motor: 10 hp 4P (8x); • Inlet conveyor motor: 2hp 8P; • Transport conveyor motor: 6hp 4P; • Hydraulic pump motor: 5hp 4P (3x);

Weeke BHP 007/430 CNC Router 13 HP HSK 63F Spindle with air blast nozzles 8 Position Rack Style ATC 7 Spindle Boring Block 4x8 Table Part location pins (2) Becker 7 HP vacuum pumps Woodwop Light Barrier safety system

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5h VANTEDGE MM 6.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): + EVA & Polyolefin Adhesive ready. Specifications: Working Capacity: Edgebanding thickness 0.4 - 3 mm coil stock capacity & 10 mm strip capacity. Min. panel width 85 mm (3.3"); min. panel length 125 mm (4.9"); panel thickness 10 - 60 mm (0.39" - 2.36"). Tape and Panel Infeed System: 750 mm Coil support table; adjustable track feed speed 14, 16 & 20 MPM (66 FPM). Heavy-Duty large solid polished steel panel infeed fence guide system. Large industrial digital adjustment for the Premill panel material removal amount. Top Pressure Beam Adjustment: Automatic adjustment from the PLC control; pneumatic Pop-Up Stop system. Red LED panel feed indicator light for correct panel spacing. Equipped with: Dual 3 HP Pre-milling motors w/diamond cutter heads; pneumatic "JUMP In/Out function. Misting unit prior to Pre-milling; large dual dust housing ports to help clean the Pre-milling system. Quick change Glue Reservoir for EVA & PO glues; Pressure Section/Infrared Heat Lamp System. Heavy-Duty automatic shear type Guillotine with: "Auto-Set" automatic intervention for strip & coil materials. (4) Pneumatic polished Pressure Rollers with manual digital adjustment to edge thickness. (1) Rubber infeed Tape Roller, (1) metal infeed Tape Roller; direct Universal Drive system - NO Chains. Teflon-coated glue pot; digital thermostats with automatic kick down when the machine is in idle mode. Workstations: End Trimming Unit: Dual 0.5 kW (0.67 HP) high frequency End Trim motors on precision "Auto Lube" Linear Guideways; 90° to 10° pneumatic tilt cut adjustment. Electronic sensors to safely monitor motor positions; thumb screw pneumatic adjustments for simplicity. Tilting Super Finish Top & Bottom Trimming Station: Dual High Frequency 0.65 kW (0.75 HP) motors with Combi Finish insert tooling.Top Servo driven positioning of motors for different edge trimming profiles & positions. Corner Rounding Unit: Motors on precision billet aluminum swing tracer arms with pneumatic guidance and Face Copy System. (2) Independent motors can be adjusted to match tape thickness via digital scales. Profile Scraping Unit: Top, bottom & side Copy Wheels to properly follow your panels edge. Panel Nesting System: Triple Copy System for panels with blind dados & hinge cup holes. Digital adjustment for fine-tuning the unit to the proper tape thickness. Flat Scraping Unit: Large copy wheels. Buffing Unit: Top & bottom Buffing Unit; 0.5 HP (0.37 kW) - 2,800 RPM motors; units tilt 0° - 30°. Dual Hot Air Blowers: To re-embellish edge materials. Operator Interface 10" Color touchscreen PLC with swivel Control Panel. The PLC controls all working units & the adhesive thermostats with 1-touch icon programmable selections. Photo indicator alarms to easily troubleshoot errors/issues. Complete with: I

VANTEDGE MM 6.0 9 C-MOTION Edgebander with Pre-milling & Corner Rounding (EVA & POLYOLEFIN adhesive ready).Specifications: -- 10" Color Tough Screen PLC. The PLC controls all work units and the adhesive thermostats with 1-touch Icon Programmable selections, Photo Indicator Alarms to easily troubleshoot, and Swivel Control Panel.Tape and Panel Infeed System: -- 750 mm Coil support table, heavy-duty large solid polished steel panel in-feed fence guide system, Large industrial digital adjustment for the Pre-Mill panel material removal amount. Top Pressure Beam Adjustment: -- Automatic adjustment from the PLC control, Red LED panel feed indicator light for correct panel spacing, Pneumatic Pop Up Stop system -- Working Capacity: Edgebanding thickness, 0.4 - 3 mm capacity. Min. panel width 85 mm (3.3"); min. panel length 125 mm (4.9"); panel thickness 10 - 50 mm (0.39" - 1.96"), Edge Height 55 mm (2.2").Equipped With: -- Dual 3 HP Pre-milling Motors w/Diamond Cutter Heads, Misting Unite w/Large Dual Dust housing ports to help clean the Pre-Milling system, quick change Glue Reservoir and Pressure Section/Infrared Heat Lamp system; consists of Heavy Duty Guillotine to cut 3 mm coil materials, (4) pneumatic polished Pressure Rollers with manual digital adjustment to edge thickness, (1) Rubber Infeed Tape Roller, (1) Metal Infeed Tape Roller; Direct Universal Drive system - NO Chains. Unit with "Auto-set" automatic intervention, Strip & Coil Edge magazine, automatic shear type guillotine. -- Hot-Melt Glue System: Teflon-coated glue pot, digital thermostats with automatic kick-down when the machine is in idle mode.Workstations:End Trimming Unit: -- Dual 0.5 kW (.67 HP) high-frequency End Trim motors on precision "Auto Lube" Linear Guideway. 90 to 10° pneumatic tilt cut adjustment. Electronic sensors to safely monitor motor positions. Thumb screw pneumatic adjustments for simplicity. Tilting Super Finish Top & Bottom Trimming Station: -- Dual High Frequency 0.65 kW (.75 HP) motors with Combi Finish insert tooling, Top Servo-driven positioning of motors for different edge trimming profiles & positions. Corner Rounding Unit: -- Motors on precision billet aluminum swing tracer arms with pneumatic guidance and Face Copy system. The (2) independent motors can be adjusted to match tape thickness via digital scales. Profile Scraping Unit: -- Top, Bottom & Side Copy wheels to properly follow your panels edge, Triple Copy System for panels with blind Dados & Hinge cup holes., digital adjustment for fine-tuning the unit to the proper tape thickness. -- Flat Scraping Unit: Large copy wheels, Insert tooling, adjustable panel spray mist cooling & cleaning system for special materials and composites, adjustable dual Buffing Wheel system, Dual Hot Air Blowers. Buffing Unit: -- Top & bottom Buffing Unit, 0.5 HP (0.37 kW) - 2,800 RPM motors), units tilt 0° - 30°.Complete With: -- Insulated sound enclosure overall trim stations with a split dust hood,

VECOPLAN RG52/60 SINGLE SHAFT SHREDDER Includes Box Dumper and ConveyorsSpecifications: --In Feed Opening: 52″ x 58″ --Rotor Length: 52″ --Rotor Diameter: 15″ --Hopper Volume: (4) Cubic Yards --Cutters: 37 --Drive Motor: 60 HP --Box Dumper / Table --Infeed Conveyor --Discharge Conveyor for Gaylord Box Loading

Vecoplan RG52-60 U Stretch Slow Speed Grinder 60 HP Motor No Control Panel

MLS Number 11342021 2008 Vecoplan RG32/20U Grinder/Shredder Single shaft grinder / shredder 80 DBA noise level 32 in. by 42 inch opening waste grinder with vertical 2 cubic yard hopper 20 HP rotor motor Equipped with10 inch rotor with 20 indexable/replaceable cutter knives Rotor / cutter head grinds at 95 R.P.M. Hydraulic pusher ram with 1.5 HP two speed pump motor Separate electrical panel with push button controls 80 DBA noise level 8 inch exhaust 8 inch hump magnet screen to produce ½ in.in size Handles 1,000 to 1,200 lbs./ hour depending on product mix and loading. Machine still operating. Will be available sometime in May/June 2022

2016 Vecoplan RG52-60 U Stretch Slow Speed Grinder 60HP Electric Main S/N 112901

Brand new never used!! 16’8” long 22” wide 19” height (adjustable)

Vecoplan Model 45/12/2VU HZF Grinder 75 HP Motor 18" Wide opening No Vibrating Infeed conveyor

Vecoplan RG 42/60 XL 60 HP Motor 15" Rotor 42" x 52" Hopper Opening 1" Screen This machine went through a rebuild. It was not big enough for the buyers application. Available immediately.

VECOPLAN RG 70/200K Shredder with Steel Belt Conveyor & Dust CollectorSpecifications: -- Hopper Opening: 70″ x 80″ -- Hopper Volume: 4 – 6-1/2 Cubic Yards -- Main motor: 200 HP -- Rotor diameter: 20″ -- Number of cutters: 84 (triple row) -- Size of cutters: 40 mm x 60 mm -- Screen size: Holes 2″ -- Rotor speed: 145 RPM -- Rotor diameter: 20″ -- Hydraulic Feed Ram: 10 HP - 2-Speed -- Throughput: 2,000 – 28,000 Lbs/HrEquipped with: -- 10 HP Motor Dust Collector -- 48″ W kW SCHMIDT Shredder Infeed Conveyor w/ 20′ pit section

VECOPLAN - RG 52, ...Single Shaft ShredderCOMPLETELY Rebuilt!VECOPLAN "RG 52" Low Noise Waste Grinder with: Vertical hopper feed; suitable for wood, paper, and plastic applications; 52" x 58" opening. -- 60 HP Rotor motor, power belt drive; 15" dia. high output "Torsion Point" cutting rotor with a (74) 4-way indexable, replaceable cutterknives. -- Rotor/cutter head grinds at approx. 120 - 140 RPM; average noise level 60 - 70 dbA. -- Includes: Heavy Duty construction stress-relieved shell and frame; tramp metal protection; oversized gear box and Heavy Duty roller bearings. -- Precision hydraulic "Process Ram" with: 5 HP, 2-Speed pump motor; fluid "TurboCoupling; monitored by programmable logic control feeding system. -- Separate electrical Control Panel with push button controls. -- Machine weight: 10,000 - 12,000 Lbs.