Equipment For Sale

Model 212 Whirlwind Chop Saw, s/n 2594M81L, 18"x8' infeed rolls, upcut saw

Whirlwind 212 And Others Various Brands And Sizes 8 To Choose From No Feed Tables

Whirlwind Pop-Up saw 212. #00804

Whirlwind Up Cut Saw with Infeed & Outfeed Rollers

Several Whirlwind Up Cut Saws Blade Capacity: 14? Cutting Capacity: 2-3/16? x 8-1/4? Motor HP: 5 Electrical: 230/460V/3PH

WHIRLWIND - 855, ...Dual Table Oscillating Edge SanderDouble-sided with: 8" x 56" Platens size.Specifications -- 7-1/2 HP - 1,725 RPM TEFC Motor; abrasive belt size: 8" x 151"; approx. (150) oscillations/Min with 3/8" stroke. -- 11" x 55" Side table; tilts 0° - 45° with 8" vertical adjustment; tiltable end table; iron frame machine base. Complete with: -- Magnetic electrical controls w/overload protection; dust hood on drive end; all standard equipment.

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i61 WHIRLWIND 1000 L Upcut Saw Specifications: 2-3/16" x 8-1/4" Cap., 14" blade cap., 3,450 RPM, left-hand unit feeding from right-to-left, 5 HP BALDOR motor. Complete with: (5 - 90) Cycles/Min; magnetic starter with low voltage controls, air filter, regulator, coalescing filter, and 4" dust chute. NOTE: The above specs are taken from literature and considered accurate. As always please take advantage of the inspection period to verify. Items seen in the background are NOT a part of this Lot.

Brand New Whirlwind blowers in stock, 8" -14" inlet, good selection, all with AR-400 steel and Dodge bearings, heavy duty built, call with your needs

Whirlwind Undercut Saw with Tiger Stop Fence

Whirlwind Sawdust Blower 36" fan 8 paddle fan 18" inlet reduced down to 17" 16" outlet

wicker forks are on a 644G loader we are parting out . Good condition for information you can contact Gavin 601/394/7796 Tim 251/366/3237 Kameron 251/242/5493 located at 467 Saint Peter Street State Line MS 39362 ALL SALES ARE CASH, CASHIERS CHECK OR BANK TRANSFER.

2005 Wilkens Walking Floor Brand New Tarp

Williams 125 CJS1 Hammermill

Williams 125 HP Hammermill 230/460 3-phase

WILLIAMS - Hammer Mill: Half-round Type ConfigurationFeatures: -- 220 HP Main Drive Motor with Belt Drive; complete with Guard. -- 26"; x 12"; Input Opening. -- Powered Input Pull Rolls -- 4"; Main Shaft with Swing Hammers, approx. 3/8"; thickness -- Ratchet Lift Access Lid. -- Mounted on Steel Support Structure with Access Platform and Ladder -- Pneumatic Bottom Discharge with built-in Viewing Window in Ducting below the Hammermill (no fan included) -- Electrical Cabinet with Motor Starters -- NOTES: This machine was last utilized to break up virgin dried pulp for further processing. Already been removed from service – ready to load.

Williams Hammer Mill 40"w #C740

24” x 36” inlet 8” x 36” outlet 150 HP motor fan on outlet

24” x 36” inlet 8” x 36” outlet 150 HP motor fan on outlet

William & Hussey "W-7S" Moulding Shaper -- Specifications: 17-1/4"x 14" Table size, 2 HP main motor, 2-knife cutter head, 3,450 RPM spindle speed, 7" max. cutting height, 1/4" min. thickness 3/4" deep max cut.. Max moulding cap. 7" wide, max. planning cap. 7" wide. -- Complete with: Dust hood outlet, electrical disconnect, and mounted on fabricated steel stand w/casters, Multi-pass

Ready to run Williams and White circle saw tooth setter. Will run up to a 42" saw.