Equipment For Sale

CMC 2 Saw Vertical Edger with 40HP.

CM Sawmill Comes With Air operated 15ft carriage Selset set works Head works with 48 inch saw 100hp electric motor Hydraulic pack with all hoses FREE Delivery within 100km of Moncton,NB Trailer not included

CMC 3 Head Block Circle Mill cab and controls carriage and Track

CM&E Chip Heads

CM&E Knife Grinder for CM&E chipping head-rig using bent knives. Many knives are available with grinder.

CM&E Chipping Heads

CUMMINS TIER 4F X-15 (500 HP) 4 PUMP HYDRAULIC SYSTEM ATTACHMENT ONE PISTON PUMP TRACK TWO PISTON PUMPS AUXILIARY FUNCTION ONE GEAR PUMP SEAL AND LUBE D-6N UNDERCARRIAGE ELEVATED FINAL DRIVE DESIGN 28" SINGLE GROUSER WITH MUD HOLE 12 VOLT ELECTRICAL SYSTEM 215 GALLON FUEL TANK 102 GALLON HYDRAULIC TANK BACK UP CAMERA FAE 300U-250 MULCHER ATTACHMENT

2023 CMI C300 282HP Mulcher Now in stock! - 282HP Cummins B6.7 Tier 4 Stage V - Equipped with Shearex HM-100SV2 Mulching Head - 100" Cutting Width / 118" Total Width - Number of Teeth on Rotor: 36 - Hydraulic Push-bar - 4 Pump Closed Loop Hydraulic System - 15,000 LB Winch Assembly - Push button cab lift with manual override - Backup Camera - Spacious Cabin with AM/FM/Bluetooth Radio - Pressurized Cabin w/ Integrated HD Pre-cleaner - Air ride seat - ROPS/ FOPS/ OPS Certification - Hydraulic oil filter pump - Steel Undercarriage w/ Single Grouser 30 in. Track Pads - D4 Type Seal and grease track - Dozer type rollers - 3.24 PSI Ground Pressure (Crawler Only) - 2 Speed Hydraulic Motors w/ 3.8 MPH Max speed - Weight (Crawler Only): 24,800 LBS - Weight (Crawler and Shearex HM-100): 29,894 LBS - Fuel Tank: 105 Gal. - Hydraulic Reservoir: 43 Gal. - Overall Width (With 30" Pad): 89" 1 Year / 2,000 Hour Warranty on Crawler 2 Year / 2,000 Hour Warranty on Cummins Engine 5 Year / 3,000 Hour Warranty on Cummins Emissions 6 Months Parts Only Warranty

2019 CMI 300 Mulcher, Cat Engine with 1600 hrs. Good undercarriage, FAE mulching head… MACHINE Overall Length: 197 inches Ground Clearance: 19 inches Overall Height: 116 inches Overall Tractor Width: 89 inches MULCHER Overall Width Attachment: 107 inches Working Width: 89 inches Overall Height (pushbar fully retracted): 64 inches Total Weight (Crawler & Mulcher): 28,840 lbs Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2019 CMI 300 Mulcher, Cat Engine with 1600 hrs. Good undercarriage, FAEmulching head… MACHINE Overall Length: 197 inches Ground Clearance: 19 inches Overall Height: 116 inches Overall Tractor Width: 89 inches MULCHER Overall Width Attachment: 107 inches Working Width: 89 inches Overall Height (pushbar fully retracted): 64 inches Total Weight (Crawler & Mulcher): 28,840 lbs Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

2023 CMI Twister II C175 now in stock! - 173HP Cummins B4.5 Stage V - Equipped with Shearex HM-70SV - Hydraulic Pushbar - 4 Pump Hydraulic System - 15,000 LB Winch Assembly - Push button cab lift with manual override - Backup Camera - Spacious Cabin with AM/FM/Bluetooth Radio - Pressurized Cabin w/ Integrated HD Pre-cleaner - Air ride seat - Resettable breakers on dash panel - ROPS/ FOPS/ OPS Certification - Hydraulic oil filter pump - Steel Undercarriage w/ Single Grouser 22 in. Tracks - D3 Sealed and Lubed track - Dozer type rollers - 3.83 PSI Ground Pressure - 2 Speed Hydraulic Motors w/ 3.85 MPH Max speed - Weight (Crawler Only): 17,411 LBS - Weight (Crawler and Shearex HM-60SV): 20,696 LBS - Fuel Tank: 78.5 Gal. - Hydraulic Reservoir: 29 Gal. - Ground Clearance: 22" - Overall Width (With 22" Pad): 82"

CATERPILLAR TIER 4F C-13 (475 HP) 4 PUMP HYDRAULIC SYSTEM ATTACHMENT ONE PISTON PUMP TRACK TWO PISTON PUMPS AUXILIARY FUNCTION ONE GEAR PUMP SEAL AND LUBE D-6N CAT OEM ELEVATED FINAL DRIVE DESIGN 28” SINGLE GROUSER WITH MUD HOLE 12 VOLT ELECTRICAL SYSTEM 215 GALLON FUEL TANK 102 GALLON HYDRAULIC TANK BACK UP CAMERA STANDARD WINCH PACKAGE FAE 300 U 250 MULCHING HEAD

2009 CMI C175 Twister, 5000 Hours, FAE Head, Excellent Undercarriage, New Head Bearings. Teeth are 90%, New Head Skid Plates, Just Fully Serviced, No Leaks. A/C

CUMMINS B4.5 STAGE V (173HP) 4 PUMP HYDRAULIC SYSTEM 12 VOLT ELECTRICAL SYSTEM 78.5 GAL FUEL TANK 29 GAL HYDRAULIC RESERVOIR SEALED AND GREASED, D3 CHAIN 22” SINGLE GROUSER TRACK PADS WITH MUD HOLES TWO SPEED HYDRAULIC MOTORS PUSH BUTTON CAB LIFT BACK UP CAMERA AM/FM BLUETOOTH RADIO HYDRAULIC OIL FILLER PUMP AIR SUSPENSION SEAT ROPS/FOPS/OPS CERTIFICATION 12 VOLTS DC OUTLET ELECTRICAL SYSTEM WITH BREAKERS IN DASH STANDARD 15,000LB WINCH FAE 140U 200 MULCHING HEAD

2020 CMI C3003200 hours, Rebuilt final drives, New rails, sprockets, and rollers, FAE 200 mulching head

2023 CMI C300 Mulcher -590 hours -Warranty -Like new Turn Key

CML NEW FINISHING TOWER/6 Multi Level Oven System: This type of oven is very flexible thanks to the FIFO (First In / First Out) operation and the possibility to adjust the stay time using more or less belt trays.It is particularly suitable to help the evaporation of the volatile components contained in UV curable paints, or to carry out a first degree of drying of conventional paints in an 'out of dust' environment. - Its technical characteristics also make this system extremely suitable for drying or curing materialDescription of the Standard Equipment & Specifications: -- Overall dimensions: 7,650 x 3,300 mm x 3,250 mm height (25’ x 11’ x 10.67’ H). -- Weight: 4.000 kG (8,819 Lbs)Multiple Floors Dryer, mod. TOWER/6 Paint Coated parts (panels components) are transported on (6) belt conveyor trays, moving vertically up/down, having a length of 6,500 mm (256") each. This practical length makes it possible to load "two panels charges" having a length of 3,000 mm. (9.85 feet) each. -- Max. weight supported by every belt tray level: 115 kG (253.5 Lbs). -- Max. allowed thickness 50 mm (1.97 inches) -- Speed controlled by inverter at belt travel steps of 3.250 mm (127.9") or in continuous model. -- Vertical movement on (4) pre-tensioned chains controlled by motor with gearbox. -- Cabinet made of structural carbon steel profiles and pre-painted insulated panels, complete with entry door and windows. -- Ventilation by means of laminar air distribution among the floors. Average air speed 2 m/Sec (6.56 feet/Sec) - (100% of the air volume is taken from the outside and exhausted to the outside). -- Air supply unit complete with centrifugal fan taking the air from the outside of the building, complete with heat exchanger to be supplied with hot water, with temperature adjustment system and double set of pocket filters. -- Air ductworks between air supply and exhaust fans and distribution boxes (plenum) is included. -- Ready to be connected to emergency system to stop the line -- Curing Tunnel operating functions controlled by SCHNEIDER PLC via electronic keypad input. -- Separate electrical cabinet in IP 55 execution - IP 55 motors -- Manufactured according to CE Standards and covered by a (12) Months or 2,000 Operating Hours Warranty for defective parts or materialOther Dims, Operation & Utilities: -- Dimensions of the electrical switchboard: 800 x 600 x 2,000 mm (2.7’ x 1,97’ x 6,56’) -- Total power: kW 10,5 -- Compressed air:: lt/Min 20 (5.29 gal/Min) -- Exhausted air volume: m³/Hr 7.500 (264,860 feet³/Hr) -- Supply air volume: m³/Hr 7.500 (264,860 feet³/Hr) -- Thermal power: Kcal/h 125.000 (326,000 BTU/Hr), - AIR In/Out: 50°C (122°F)

This machine is in good working condition and can be inspected under power. Specs (to be confirmed): - Electric spindle 18.1 HP - X-axis stroke 145.66î - Y-axis stroke 82.67î - Z-axis strke 13î - Working area 145.66î x 68.90î - Automatic tilting head - Telescoping spindle extension for surface polishing - (26) ISO 40 tool holders at rear - Bar code reader for program interface

CMS NC-P.F./112-TUCU 5' x 12' 5-Axis CNC Router, with ATCSpecifications: -- Travels: X-Axis (Side-to-side) 3,600 mm (141.73"), Y-Axis (Front-to-back) 1,600 mm (62.99"), Z-Axis (Up-and-down) 700 mm (27.56"), 4th Axis (Around Z-Axis) 360° Continuous, & 5th Axis (Head inclination) +/- 100°. -- Distance between housings 155". -- Feed speeds: X-Axis 0 - 54,000 mm/Min. (0 - 2,125.98 IPM), Y-Axis 0 - 45,000 mm/Min. (0 - 1,771.65 IPM), & Z-Axis 0 - 10,000 mm/Min. (0 - 393.70 IPM). -- Positioning speeds: X-Axis 54,000 mm/Min. (2,125.98 IPM), Y-Axis 45,000 mm/Min. (1,771.65 IPM), & Z-Axis 10,000 mm/Min. (393.70 IPM).Equipped with: -- (2) 1,830 LR x 1,560 mm FB (72.05" LR x 61.42" FB) Moving tables, with Independent or synchronized movement, LIGNOSTONE surface, & Ground & tempered interchangeable slideways. -- CMS "TUCU" Universal 5th Axis head, with 8 kW (10-3/4 HP) - 18,000 RPM - 600 Hz ISO 30 Air-cooled electrospindle, with Variable spindle speeds 0 - 18,000 RPM, Max. Tool Length & Dia. 110 mm (4.33"). Electronic brake, Reverse, & BERGES "ACI 22" 22 kW (30 HP) Frequency static converter. -- 12-Position Automatic tool changer.Features: -- X, Y, & Z-Axes Carriages, with Ground & hardened sideways via 4-Point hitch (Recirculating, linear, & self-cleaning) bearing (Star-type), & AC Servo motors with Precision dual lead ball screws, Z-Axis with Automatic insert brake. -- Pneumatic compensating cylinders. -- Automatic centralized pressure-injected lubrication.Operator Control: -- ALLEN-BRADLEY/OSAI "86S0 MC" CNC Control, with 9" Color CRT, Color graphic visualization & tool path process simulation, Spiral interpolation, Parameteric functions, Tool radius & length compensation, Brief description of tool path for simple generation of part programs, Teach-in function, Double push button control, & PC.Complete with: -- Documentation. -- EATA "CRIA 2.5 EU3 VE" 15 L (3.96 Gallon) Cap. Chiller. -- BECKER 3 kW (4 HP) Vacuum Pump. -- Spare Spindle. -- Toolholders.NOTE: Machine currently not operational due to control/drive issues.Machine Dimensions: 202" x 140" x 138" H.Control Dimensions: 26" x 24" x 57" H.Control/Electrical Cabinet Dimensions: 40" x 36" x 96"; H.Chiller Dimensions: 24" x 19" x 39" H.Vacuum Pump Dimensions: 36" x 26" x 43" H.

CNC FACTORY PYTHON XPR FLAT TABLE MACHINE (W/ATC): -- Specifications:4' x 8' Flat Table "Bridge Gantry" machine with: "Phenolic "MATRIX" grooved flat table for "NESTED BASE MANUFACTURING". -- Working capacity:"X" Axis 97" (2,464 mm); "Y" axis 49" (1,245 mm); "Z" axis stroke is 20.2" (515 mm); max. material thickness 10" (250 mm). -- Positioning Speed:"X" & "Y" Axis 279 FPM (85 MPM); "Z" axis 115 FPM (35 MPM).All axes movement is with 5G driverless Servo System with direct helical rack & pinion & 5G no homing calibration. -- Work Area:Flat table design with: "Matrix" grid phenolic surface for "Nested Base Manufacturing".The machine has: (6) Independent working zones with dual layer high flow vacuum; 2-left origins, 2-right origins, 1-front origin & 1-rear origin.Auto-material alignment pins, auto-unloading arm, material loading wheels; rear & side material alignment pushers. Automatic on/off vacuum flow, vacuum hold-down communication, automatic parts hold down, and release.Robotic Material Sensing Dust Hood; Single and dual vacuum ports. -- Machining:(1) 12 HP (8.9 kW) Air-cooled "HSD Electro-Spindle" with: ISO 30 adaptor, RH & LH rotation; variable speed from 1,000 - 24,000 RPM.(1) Rapid Fire 12-position revolving tool changer for "on the fly "ATC". -- Operator & Machine Control:"SYNTEC" PC Front End with: CNC Factory 5G, 5th generation CNC control + At machine cabinet and cutting software. Handheld MPG remote control with individual axis & real time simulation control; CNC speed control overrides & compensation at machine virtual support, HD digital monitoring camera, Wi-Fi, and Ethernet ready.Air-Conditioned control cabinet, 21" "TOUCH SCREEN" monitor; All mounted on a mobile cart. -- Complete with:(1) 150 cbm (60 Hz) Vacuum Pump; automatic pressurized Lubrication System for linear guides, pads and recirculating ball screw. Auto tool length measurement probe. Perimeter Safety System & fencing. -- Actual Model is: CNC FACTORY PYTHON XPR CNC