Equipment For Sale

Filtering

Reset All 

thru
 Used     New
Viewing Page 467 of 495
9898 Results Found
Sort By 
Call for Price

VECOPLAN RG 42-40 SINGLE SHAFT SHREDDERSpecifications; -- 40 HP MotorVecoplan ShredderModel: RG 42/40 XL PVYear: 2007Motor: 40 HP, 460V, 60HZRPM: 1465Feed Opening: 42" x 48"Blades on rotor: 27Weight: 3,700 lbs

Katie Lechelt
800-374-5009 ext:452
Call

Call for Price

VECOPLAN RG52/60 SINGLE SHAFT SHREDDER Includes Box Dumper and ConveyorsSpecifications: --In Feed Opening: 52″ x 58″ --Rotor Length: 52″ --Rotor Diameter: 15″ --Hopper Volume: (4) Cubic Yards --Cutters: 37 --Drive Motor: 60 HP --Box Dumper / Table --Infeed Conveyor --Discharge Conveyor for Gaylord Box Loading

Katie Lechelt
800-374-5009 ext:452
Call

Call for Price

Vecoplan RG 42/60 XL 60 HP Motor 15" Rotor 42" x 52" Hopper Opening 1" Screen This machine went through a rebuild. It was not big enough for the buyers application. Available immediately.

Carolina Machinery Sales, Inc
704-288-1904
Call

Call for Price

VECOPLAN RG 70/200K Shredder with Steel Belt Conveyor & Dust CollectorSpecifications: -- Hopper Opening: 70″ x 80″ -- Hopper Volume: 4 – 6-1/2 Cubic Yards -- Main motor: 200 HP -- Rotor diameter: 20″ -- Number of cutters: 84 (triple row) -- Size of cutters: 40 mm x 60 mm -- Screen size: Holes 2″ -- Rotor speed: 145 RPM -- Rotor diameter: 20″ -- Hydraulic Feed Ram: 10 HP - 2-Speed -- Throughput: 2,000 – 28,000 Lbs/HrEquipped with: -- 10 HP Motor Dust Collector -- 48″ W kW SCHMIDT Shredder Infeed Conveyor w/ 20′ pit section

Katie Lechelt
800-374-5009 ext:452
Call

$ 70,000

This listing Is for a complete line that consists of a Flow Coating line that feeds into a cross transfer oven and back out on to an outfeed conveyor making a 180 degree circuit. The heat exchanger needs to be heated by means of a hot water boiler or similar. Maximum Part width: 305 mmSpeed range: 2 - 10 m/min.Pos. 1 - FEEDING BELT CONVEYOR:For feeding the batches into the flowcoater, Belt with marked area to built a gap for the angle transfer, Technical Data: length: 2300 mmPos. 2 - IMPREGNATION MACHINE VEN FLOW:For flowcoating of profiles in continious production with a waterbased impregnation (viscosity similar to water)The material is is sprinkled on the surface and remains for appr. 10 seconds. After this time a high pressure air knife nozzles will blow the acess materialfrom the surface. The whole cabin is built with fall to the side to collect the rest of the material. It is reused after passing a filter system. The cabin is built of stainless steel. The blowing off of the access material by air knife is effected by a high pressure fan.The machine comprises:1 conveyor system with spray protected roller system length 3000 mm1 sprinkling zone with two nozzle systems adjusted to reach the whole surface of the workpiece. length: 200 mm1 penetration area length ca. 1000 mm time of residence ca. 10 sec1 blowing zone with adjustable knife nozzles air supply with high pressure fan air flow adjustable by frequency converter length ca. 1000 mmair speed ca. 40 m/sec. material supply to supply the two sprinklers with fluid and collector for recovered material.workpiece tolerances:twist: max. 1° on the whole length, straightness max. 0,5mm deviation/m in horizontal and vertical weight distribution: evenly on whole length coating material: waterbased impregnation. Unstable components can not be repositioned when tilted.Pos. 3 - MOULDING ANGLE TRANSFER VEN TRANS 90°conveying from lengthwise direction to crosswise, comprising:1 excenter-transfer arms integrated into the driven infeef roller conveyor. The tacted transfer system allows a minimum distance between the singlemouldings on the following cross transfer system.Technical Data:length of roller conveyor: 4500 mmroller pitch: 185 mmnumber of transfer arms: 22spacing 185 mmtacting cycle: max. 30/min.Pos. 4 - MOULDING CROSSWISE V-BELT CONVEYOR:Mouldings are conveyed by means of various v-belts along the system. The unit is fitted with an insulation cover between the conveyor. A drying tunnel is fitted on top of the unit.Technical data:length: 4000 mmoperating width: 4200 mmnumber of belts: 22distance of belts: 185 mmoutfeed prepared for an additional angletransfer:position of driving shaft in the middlegaps for passing of the carriers of the angle transferPos. 5 - JET DRYING TUNNEL 70 °C:Made of sandwich elements with fire preventing insulation material. The even distribution of air over the full operating width is reached by using slot nozzles on the full width of the tunnel. One combined heating-, fan

Dan Wolters
800-374-5009 ext:376
Call

$ 7,500

John Deere 1010E Forwarder Tracks and Tires Veriga tracks at 90% Used approximately 800 hours Three Nokian Forest Rider 650-45-24.5 tires at 80% mounted on rims and one rim

Mike Stuck
828-773-2204
Call

$ 460,000

2017 Vermeer TG7000 Tub Grinder w/Cab and Loader. Work ready machine. Cat C27 950 HP, air compressor, magnetic head pulley, Remote control, auto reversing fan, Series duplex drum. 7175 Hours $460,000 OBO 616-875-2241

 Zeeland, MI
616-875-2241
Call

$ 410,000

Hours-1,677 Serial Number- 1VRC312H8K1001097 Low-hour late model grinder That was used for regrind. The machine is very clean and straight for age and hours. Machine Has Full Factory Warranty Remaining Delivery is available at the buyer’s expense

Vernon Novak
828-773-6456
Call

$ 245,000

2013 Vermeer HG6000 -6000 hours -CAT C-18 engine -New material output belt that comes with it -Tires and lights good

Josh Digirolamo
828-302-7264
Call

$ 180,000

Josh Digirolamo
828-302-7264
Call

$ 165,000

2023 Vermeer Vacuum excavator VX75A1055 -148 hours -500 gallon spoils tank -250 gallons water storage -Remote control boom -74 HP Tier 4 diesel -1,200 CFM vac -3 stage filtration,8 GPM @ 3,000 PSI -Heater box option Fully loaded unit like NEW

Josh Digirolamo
828-302-7264
Call

$ 64,500

Lightly used ready to go machine.

 Bridgewater, NH
Michael F Sharp Enterprises
603-252-6689
Call

$ 65,000

2010 Vermeer HG6000 Horizontal Grinder-Around 3K Hours, Cat C-18, 750hp, municipal owned, fire damaged, $65,000 518-434-2747

 Albany, NY
WM Biers, Inc. Port of Albany
518-434-2747
Call

$ 219,900

2015 Vermeer FT3001358 hours Can run carbide to chipper teeth

 Brainerd, MN
U.S. Equipment Sales
877-451-9525
Call

$ 1,500

Vermeer HG6000 3/4" Square Baffel Screen Only had half a truck load ran through it

Carolina Used Machinery
828-773-2204
Call

Call for Price

2013 Vermeer TR626 Wildcat Trommel Screen with 13,000 hours. Recently had all frame work redone – details can be provided. Weight: 47,500 lbs Width: 102 in (8 ft 6 in) Height: 13 ft 4 in Length: 49 ft Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

 Ocala, FL
NEF Equipment
855-251-2648
Call

Call for Price

2012 Vermeer TR626 Wildcat Trommel Screen with 12,500 hours. Weight: 47,500 lbs Width: 102 in (8 ft 6 in) Height: 13 ft 4 in Length: 49 ft Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

 Ocala, FL
NEF Equipment
855-251-2648
Call

$ 275,000

2009 Vermeer HG6000TX Grinder -10,350 hours -New Infeed conveyor, -New Chain and roller -New idler roller bearing -New infeed wear strips -New hammer feed drive belts -New anvil bars -New shear edge and cutters -New mill seat new tail belt -New roller lock cylinder and more -Over 150k in repairs done about 300 hours ago Have receipts of all work!!!!!!!!

Josh Digirolamo
828-302-7264
Call

Call for Price

2014 Vermeer 2300XL Whole Tree Drum Chipper, C13 Cat 440HP with 4474 hours, Infeed, Remote, Woods Ready. Disclaimer The information is the best of our knowledge at the time of the listing. The price may change without notice and additional charges may apply, including freight, taxes, duties, tariffs, quarantine, etc.

 Keene, NH
NEF Equipment
855-251-2648
Call

$ 177,900

2007 Vermeer HG6000 6400 hours 50 hours on rebuilt motor New belts last year New screen Bought a track grinder and no longer need

Mitch Stevens
828-773-6986
Call

Contact Us
  • Toll Free & Canada: (800) 477-7606
  • Direct & International: (931)381-1638
  • Location: 2508 Pillow Dr. Columbia, TN 38401
Copyright © 2020 LumbermenOnline.com - All Rights Reserved