MARINUS Powermax 300 HD End Matcher With Defecting, Cut to Length & Optimizing Cut-Off CapabilitiesFeatures & Specifications: -- Heavy and stable construction -- Cutterhead Carriage and Clamp System utilizes HD Lineal Bearings – grease lubricated. -- Heavy Duty – low maintenance Feed Chains Into machine and takeaway of material after cutting/ end matching. -- Continuous high-speed feeding system with accurate positioning utilizing HD Servo Drives. -- 2 Servomotors for maximum feed control and acceleration and deceleration control -- Servo-driven feed motor & gearbox for highest efficiency speed feeding and control of the cutterhead carriage includes independent step-less speed control forward & reverse. -- Pneumatic side pushers (holding material firmly against the fence) for guaranteed square angle cut. -- 2 Cut-off sawing servo motors: 5 HP each (3,0 kW) – 450 mm (17.7";) dia. blades with inverters (VDFs) for varying blade speed -- 2 High-speed milling head servo motors with inverter (VFD) (12HP - 7,5 kW each) with speeds to 12,000 RPM - 5"; (125 mm) dia. -- Adjustable cutterhead stroke based on material width to increase throughput speed based on the width of material input. -- 1 Luminescence-Sensor camera for defect crayon mark -- Inductive-Sensors – for detecting the position of the carriage and the others for detecting the positions of the saw blades. -- Cutoff waste powered belt conveyor in machine (below feed system- 12"; from floor) with drive motor for waste cutoff pieces taken to the outfeed end of the machine. Other Technical Specification: -- Machine is completely enclosed by safety doors. -- Machine is produced to CE Safety and Electrical Standards to UL/CSA Standards -- Lenze PLC Control -- Operation from operator’s control with touch screen control – mounted on the front right cover of the machine. -- Air pressure required – 85 PSI (6 Bare) -- 1x 8"; (200 mm) & 2 x 4.75"; (120 mm) dia dust outlets with approx. 5,000 to 5,500 mm and from 3050 to 3350 CFM -- Router Remote Access – with an internet connection, factory can monitor the performance of your machine. Also allows for easy access to service and softwareupdates and downloadsInput & Output Material Specifications -- Board Widths: 2";(50mm) Min. to 12.28";(312mm) Max. Min width 1.75"; (44.5 mm) min. -- Board Input Lengths: 17.9"; (450 mm) Min. to 20 ft.(6000mm) Max. -- Board Output Lengths: 15.9"; (400 mm) Min. -- An available short-piece option can be added to reduce output. length to 10"; (250mm) Min -- Board Widths: 2";(50 mm) min. to 12.28";(312 mm) max. -- Board Input Lengths: 17.9"; (450 mm) Min. to 20 ft. (6000 mm) Max. -- Board Thickness:4"; (10 mm) Min. - (to 0.315"; (8 mm) on request) (to 2"; (50 mm)Standard Programs / Programming -- The machine is equipped with 2 Primary Programs: -- 1. Endmatching – includes trimming ends and endmatching -- 2. Cutting only (no endmatching) -- 3 Sub-Programs -- 1. Defecting

MARCUS TRANSFORMER 15 KVA, 3-Ph, Auto, 600/480 V Transformer with tap for 440 V.15 KVA Auto-ventilated "dry type" transformer 600 V in (primary); 480 V out (secondary) with tap on secondary for 440V at full capacity. -- Manufactured with grain oriented silicon steel is used. -- Coil windings with high quality magnet wire and the enclosure is made of heavy gauge steel w/ventilation openings. -- UL and CSA approved.

MARTIN T 23 Tilting Spindle Shaper, with 30 mm (1.18") Interchangeable Spindle & Power FeederSpecifications: -- Table size 940 x 1100 x 850 mm (37.01"; x 43.31"; x 33.46";) H, with Table insert dia. 90, 130, 205, 305, & 480 (3.54";, 5.12", 8.07";, 12.01";, & 18.90";). -- Spindle tilt 0° to 45°. -- Maximum capacity under nut 7". -- Vertical spindle adjustment 145 mm (5.71"). -- Spindle speeds 3000, 4,500, 6,000, & 90,000 RPM.Equipped with: -- 6.4/7.8 HP Motor. -- "MK5" Spindle shaft. -- Mechanical spindle brake, with Foot pedal. -- Hand spindle lock.Complete with: -- 11-1/2"; x 4-3/4"; Left & Right Fences, with 21"; x 6"; H Left & Right Wood fences. -- 1996 CO-MATIC 1 HP 4-Speed 4-Roll Power Feeder, with Speeds 13, 26, 26, & 72 FPM.Dimensions with Power Feeder: 42" x 42" x 63"; H.

MARUNAKA Model RD – 8J WIDE Single Deck Veneer Roll Dryer;Complete with the following features: -- 1988 - year of manufacture. --Working width – 51"; --Length of the dryer – 24 Ft (4 Sections) --Type of heating - Steam --Operational in 2018 when mill closed --Professional rigging and loading available.

MARUNAKA Model RD-3UB/RD-6UB (Connected) Single Deck Veneer Roll Dryer;Complete with the following features: -- (3) 3 HP circulating fans with (1) 3 HP exhaust blower thru the ceiling. -- Optional heat source: electric (7) Elements/Zones, computer controlled thermocouples in addition to (2) Natural gas burners (OEM).. Both dryers have a 100amp circuit breaker with 100amp fuses. The RD 8 operates with 4 fan motors and 4 heaters. The RD 6 has 3 fan motors and 3 heaters";.. -- Capable of temperatures to 120° Celsius (250° Fahrenheit). -- Working width 1000 mm or about 39 inches. Veneer is fed endo.Please Note: -- Dryer is (2) separate units; all equipment will fit into a 40' container for shipment from Eastern USA. -- All equipment is in good working condition including all fans and blower, temperature control works properly; feed roll drive works well. -- Rolls have been nickel treated to minimize corrosion/oxidation. -- This dryer equipment is still in place. -- MARUNAKA (2) Models: RD-3UB and RD-6UB currently connected to increase capacity. Can easily be separated.NOTE: Refurbished in 2005, operated from 2005 - 2012. Still operational ready to work!

MASTERWOOD PROJECT 313 CNC MACHINING CENTER (W/ACT/BORING): -- Specifications:Working Capacity:"X" Axis 3,080 mm (121"), "Y" axis 1,100 mm (43") width; -- Positioning Speed:Programming speed in X-axis 197 FPM (60 MPM), Y-axis 162 FPM (49 MPM), Z-axis 58 FPM (18 MPM). -- Boring unit:(13) independent vertical spindles, (9) in X-axis, (5) in Y-axis; (4) horizontal spindles with (1 + 1) in X-axis for edge boring in the left- & right-hand panel edges. -- Machining:(1) 7.5 HP (5.6 kW) high speed router (1,000 - 24,000 RPM) by frequency inverter; 1.5 HP (1.1 kW), 6,000 RPM grooving saw with manual rotation for X-axis or Y-axis; -- Work Table: (6) moveable support rails with (2) vacuum cups ea., double zero settings, (6) pneumatic backstops and (2) pneumatic side stops creating (2) working zones. -- Operator & Machine Control:TECNOSUD "K68800" Microprocessor control for (3) axis, lineal, circular, and helical interpolation. Equipped with 14" color video graphic monitor, keyboard for data entry, 1.44 MB floppy disk drive, 64K RAM, RS-232 for possible connection to office PC, all mounted in separate free-standing control cabinet; features to run CPL/Parametric "TRIG" programming and "Spline" CAD/CAM. -- Complete with: Dual zone vacuum pump. Ontario Hydro approved electrics. -- Actual Model is MASTERWOOD PROJECT 313

MASTERWOOD OMB1CN3-TF Horizontal Slot Mortiser. One NC working head (3) axis with programmable microprocessor.. Machines a sequence of slots on windows, doors, shutter, or cabinets without moving workpiece. Continuous cycles with loading/unloading. -- Equipped with: (1) Maka style chisel mortising unit, (1) Vertical routing unit and (1) TF Horizontal routing unit. High frequency drilling - routing with controlled axis, DC motors, ball screw driven. -- Max Mortise workpiece size 150x110x2800 mm length, (5.9"x4.3"x110.2"). Vertical and horizontal routers 142"; length. -- Max slot depth 130 mm (5.1"). Max vertical head stroke 140 mm (5.5"). -- Features: Pneumatic hold-downs bar mounted above table. Flip-up pneumatic pressure beam for additional support when needed. Free-standing control and electrical cabinets house computer monitor and keyboard. Master universal electronic system controller (MW CN10 Centromac) -- Vertical routing assembly: 4HP, 220/380v 3 PH, 9,000 RPM -- Horizontal routing assembly 5"; 220/380v, 3 PH, 9,000 RPM -- Memory for 50 cycles. Mirror imaging with preset tool speed (over-writeable knob). -- Total load 21 KVA -- Overall dimensions 4200mm long x1600x1600mm (166"x63x63"). Electrical cabinet 1,000 high x 450x950mm (40"x 18"x38"). Approx. weight 3800 Kg (8,400 Lbs.).

MATH-EX (6) PERSON BASIC RECYCLING SORT LINESpecifications: -- 16 Feet x 32" Inclined feed conveyor with 48" high hopper and 2" high cleats @ 36" centers. -- 36 Feet x 32" Sort conveyor with infeed transition guides and Belly rest skirt on one side. -- Sort platform with OSHA stair and handrail. -- (6) Sort chutes with 52" of clearance. -- 1-1/2 HP, 460 volts 3-phase drives.Custom order your Sorting Line with approx. 7 to 8 week lead time for delivery.

MATH-EX (6) PERSON BASIC RECYCLING SORT LINE -- 16 Feet x 32" Inclined feed conveyor with 48" high hopper and 2" high cleats @ 36" centers. -- 36 Feet x 32" Sort conveyor with infeed transition guides and Belly rest skirt one side. -- Sort platform with OSHA stair and handrail. -- (6) Sort chutes with 52" of clearance. -- 1-1/2 HP 460 volts 3 phases drives. -- (2) VFD Controllers mounted in control panel -- Pedestal style stand. -- Emergency pull cord stop or-E-stop for sort conveyor -- Motor wire and flex conduit for (2) conveyors shipped loose. -- BRAND NEW WITH WARRANTY -- ALLOWS 7 TO 8 WEEKS DELIVERY -- LOADED ON YOUR TRUCK

MATH-EX (6) Position (Person) Basic Recycling Sort Line Specifications: -- 16 Feet x 32" Inclined feed conveyor with 48" high hopper and 2" high cleats @ 36" centers. -- 36 Feet x 32" Sort conveyor with infeed transition guides and Belly rest skirt one side. -- Sort platform with OSHA stair and handrail. -- (6) Sort chutes with 52" of clearance. -- 1-1/2 HP, 460 volt, 3-phase drives. -- (2) VFD Controllers mounted in control panel -- Pedestal style stand. -- Emergency pull cord stop or-E-stop for sort conveyor -- Motor wire and flex conduit for (2) conveyors shipped loose. -- (1) 6" Diameter Ceramic Drive Pulley -- (1) Stainless steel Back ChuteOptional Equipment: -- (2) VFD Controllers mounted in control panel -- Pedastal style stand -- Emergency pull cord stop or E-Stops for sort -- More wire and flex conduit for (2) conveyors

MATH-EX 4-Position (Person) Basic Recycling Sort Line Specifications: -- Slider bed belt conveyor: Model 600, Style B. -- Frame construction: 10-auge, bolt together. -- Pulley diameter: 6" Dia. -- Conveyor length: 16'. -- Angle of incline: 25°. -- Effective width: 32". -- Belt: Black PVC 120 COS. -- Endura-cleat: 2" High @ 48" centers. -- Side skirts: 12" High (tob), 12-gauge. -- Belt return: Bottom pans. -- Belt speed: 60 FPM. -- Drive mount/side: Shaft mount, right-hand side. -- Motor: 1 HP, 460 V, 3-Ph. -- Live load capacity: 394 Lbs. (fixed speed). -- Controls: Start/Stop control - (2) e-stops - mounted and wired. -- Infeed height: 0" BOF. -- Discharge height: 83" BOF. -- Supports: provided.Included Features: -- Black side guides -- Bottom pans. -- Infeed hopper. -- Transition guides.Overall floor-length: 174" (end to end).Approximate shipping weight: 1,876 Lbs (includes platform and controls.) Plus packaging.

OMGA RADIAL 600 P3S Radial Arm Saw - 24" Crosscut Solid saw carriage with replaceable tempered steel sliding tracks. -- Carriage travels on (8) bearings with dust scrapers for smooth travel & extended track life. -- 180° Swivel of entire saw carriage for mitered crosscuts. -- 45° Saw head tilt for compound miter cuts. -- Spring loaded return for safe return of saw head after completion of the cut. -- Oversized replaceable wooden tabletop with full length back fence. -- Fabricated open steel base. -- Electromagnetic brake to stop the blade within (2) Seconds. -- Magnetic controls, push button controls & thermal overload switch. -- Options: Single-phase motor, Blade, Dado head guard, Dust collection system, and Roller tables for infeed & outfeed.

OMGA RN 450 Radial Arm SawSpecifications: -- 3 HP Saw motor; 12" blade; 17-3/4" crosscut cap.; 26-3/4" rip cap.; 3-1/2" @ 90° thickness cap., 2-1/2" at 45°; 1-1/2" dado cap.; solid saw carriage with replaceable tempered steel sliding tracks. Equipped with: -- Carriage that travels on (8) bearings with dust scrapers for smooth travel & extended track life.180° Swivel of entire saw carriage for making mitered crosscuts; 45° saw head tilt for compound miter cuts; spring-loaded return for safe return of saw head after completion of the cut. Complete with: -- Oversized replaceable wooden table top with full-length back fence; fabricated open steel base; electro-magnetic brake to stop the blade within (2) seconds. Includes: -- Magnetic controls, push button controls & thermal overload switch. -- Single-phase 2 HP motor available.

OMGA Radial 1250-7 Radial Arm Saw -- Specifications: 7 HP Saw motor, 43.897" crosscut cap. at 90°; 6-7/8" thickness cap. at 90°, 4-7/8" at 45°; 59" rip cap.; 20" dia. blade with 1" bore; 1-3/4" max. dado cap.; 3,400 RPM Arbor Speed. -- Features: Solid saw carriage with replaceable tempered steel sliding tracks. -- Carriage travels on (8) bearings with dust scrapers for smooth travel & extended track life. -- 180° Swivel of entire saw carriage for mitered crosscuts. -- 45° Saw head tilt for compound miter cuts. -- Complete with: Spring loaded return for safe return of saw head after completion of the cut; 58" x 44" replaceable wooden tabletop with full length back fence; fabricated open steel base; electromagnetic brake to stop the blade within (2) Seconds. -- Includes: Magnetic controls, push button controls & thermal overload switch. -- OPTIONAL EQUIPMENT WHEN ORDERED WITH MACHINE: -- Automatic Air-Over-Oil Head Feed System, foot pedal activated, add $4,379.00 -- Vertical Pneumatic Clamp, add $ 675 -- Horizontal Pneumatic Clamp, add $929 -- RH or LH Roller Table, 6'-7" X 24", add $1,687 -- 3' Aluminum Fence Extension, add $410 -- 6' Aluminum Fence Extension, add $580

OMPEC TRO/10/R50 TYPE CE 3200 10-1/2' Hydraulic Veneer Guillotine, with 10° Cut & 50 mm (1.97") Fence TeethSpecifications: -- Max. cutting length 3,250 mm (127.95"), Nominal cutting length 112". -- Cutting width 23 - 1,020 mm (0.91" - 40.16"). -- Max. cutting height 80 mm (3.15"). -- Table height 950 mm (37.40").Equipped with: -- 7.5 kW (10 HP) Hydraulic motor. -- Motorized parallel back fence, with 1/2 HP Motor, Digital readout, Hand wheel for fine adjustment, and Ball screw guides. -- Two-Handed operation & Safety light curtain.Complete with: -- Manual. -- Replaceable cutting pads.Machine Dimensions without Back Fence/Table or Hydraulic Unit: 192" x 20" x 76" H.NOTE: Very well maintained, though machine has been stored outside under tarp since Mid-2023, thus some surface rust can be expected.

--Make an Offer!--Liquidation Surplus Machine-- OMPEC TRO/10/R50 TYPE CE 3200 10-1/2' Hydraulic Veneer Guillotine, with 10° Cut & 50 mm (1.97") Fence Teeth Specifications: Max. cutting length 3,250 mm (127.95"), Nominal cutting length 112". Cutting width 23 - 1,020 mm (0.91" - 40.16"). Max. cutting height 80 mm (3.15"). Table height 950 mm (37.40"). Equipped with: 7.5 kW (10 HP) Hydraulic motor. Motorized parallel back fence, with 1/2 HP Motor, Digital readout, & Hand wheel for fine adjustment, and Parallel rack & pinion guides. 2-Handed operation & Safety light curtain. Complete with: Manual. Replaceable cutting pads. NOTE: Very well maintained, though machine has been stored outside under tarp, thus some surface rust can be expected.

ONEIDA AIR SYSTEMS XXK050346 Cyclone Dust Collector w/ After-filter Plenum. Cyclone & Cartridge Fabric Filtration Dust Collection System for High Pressure CNC applications (need more static pressure for effective cleaning of cutter heads). -- Performance: 2,120 CFM @ 2" SP with Filter. 5 HP US Made BALDOR , Class F, TEFC motor. Magnetic Starter w/ on-off switch and overload protection. -- Fan/Wheel housing: Extremely strong cast aluminum, non-sparking (per NFPA fire code). Efficient Backward Inclined high performance and low noise. No rivets or welds. Fully welded fan housing 11 ga. Motor Housing plate. Includes: -- Cyclone: (8") solid welded inlet with Neutral Vane. Technology reduces filter maintenance. 16-gage cyclone barrel with solid welded construction. Rectangular outlet cam be rotated independent of inlet - 8-bolt patterns. Outlet is 10.03" x 7.64" inside dimensions. Square to round adaptor available. Approx. 26" dia. cyclone housing. -- After-filter plenum for (10) filter bagsDust collector is missing cyclone stand and filter bags. .

ONEIDA AIR SYSTEMS XXK200300 Cyclone Dust Collector w/ Rotary Air Lock: Cyclone & Fabric Filtration Dust Collection System. -- 3,800 CFM @ 12" SP to 6,800 CFM @ 2.7" SP with 20 HP Baldor Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (4) High Efficient Axtar Spun-Bonded Media cartridge after-filters for 620 sq. ft. of filter media with inverted plenum. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Fan is welded carbon steel, backward incline, dynamic, two plane balanced. Same as aircraft turbine rotors. -- 16" Rectangular Inlet with square to round inlet adapter. -- Includes: Freestanding Leg Kit with Rotary Airlock, magnetic starter, internal silencer reduces sound to 82 dB @ 10'. MADE IN THE USA.

ONEIDA AIR SYSTEMS FXK041500 Cyclone Dust Collector w/ After-Filter Plenum: Cyclone & Fabric Filtration Dust Collection System. -- 3,800 CFM @ 12" SP to 6,000 CFM @ 2.7" SP with 15 HP Baldor Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (4) High Efficient Izumi Axtar Spunbond Media cartridge after-filters (hanging) for 620 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Fan is welded carbon steel, backward incline, dynamic, two plane balanced. Same as aircraft turbine rotors. -- Inlet size 14" round. outlet 16" round dia. -- Includes: Heavy Duty angle iron stand, magnetic starter, internal silencer reduces sound to 85-87 dB @ 10'Includes Rotary Air-lock for dumping into a waste bin!MADE IN THE USA.

ONEIDA AIR SYSTEMS XXK070323 Cyclone Dust Collector w/ Rotary Air Lock: Cyclone & Fabric Filtration Dust Collection System.Specifications: -- 2,900 CFM @ 1.5" SP with 7.5 HP US Made, Class F, TEFC motor with 1.15 service factor. -- High efficiency 12-gauge cyclone barrel with fully seam-welded construction. Powder coated paint finish, weather-proof cyclone and fan blower. -- (2) High Efficient Izumi Axtar Spunbond Media cartridge after-filters for 310 sq. ft. of filter media. Filters 99.9% efficient of 0.2 - 2.0 microns, Teflon-like coating to facilitate dust cake release. -- Impeller is 16.5" Diameter, Single-piece, backward inclined, non-sparking/non-ferrous, cast aluminum alloy. -- Inlet size 10" round. outlet 12" round dia. Includes: -- Rotary Air Lock, magnetic starterOptions: -- Freestanding Leg Kit with Dual 55-Gallon steel drum less Rotary Air Lock...as for pricing. MADE IN THE USA.(Actual P/N XXK070323-460-AIR).