Woodworking Equipment For Sale

MAKITA LS1013 10" Double Bevel Sliding Compound Miter Saw, with Stand Specifications: Miter angles 52° Right & 47° Left, with (9) Positive stops at 15°, 22.5°, 31.6°, & 45° Left or Right & 0°. Bevel angles 45° Right & 45° Left. Dimensional lumber cut capacity: 2" x 12" at 90° & 2" x 18" at 45° Left. Arbor dia. 5/8" Equipped with: 1,430 W - 13 A - 3,700 RPM Motor, with Electric brake. Complete with: DELTA "55-155" Universal Miter Saw Stand. Machine with Stand Dimensions: 104" x 28" x 59" H. Machine Dimensions: 30" x 28" x 25" H. Machine Weight: 50 Lbs. Stand Dimensions: 104" x 22" x 35" H. Stand Weight: 85 Lbs.

Makor Start One M (S-ONE-M) Finishing Line Infeed & Outfeed System Storage Trolleys This line has been removed from operation and is in dry storage, as shown in the last (3) photos.

MAKOR LTS/6E Profile Sander(6) Stations, 6"Width Capacity (approx), PLC Controller. -- 5.5HP Variable Speed Feed Motor with (6) 6"W Powered Feed Belts. -- 1st Station: Tiltable 3-Point Oscillating Profile Sander, 24" Contact Sanding Area, 2HP MAKOR Motor with Cooling Fan and J1000 Drive. -- 2nd Station: Tiltable 3-Point Oscillating Profile Sander, 24" Contact Sanding Area, 2HP MAKOR Motor with Fan and J1000 Drive. -- 3rd Station: Tiltable Polishing Head 2HP MAKOR Motor with Fan and J1000 Drive. -- 4th Station: Tiltable Polishing Head with with 2HP MAKOR Motor with Fan and J1000 Drive. -- 5th Station: Tiltable Polishing Head with 2HP MAKOR Motor with Fan and J1000 Drive. -- 6th Station: Tiltable Polishing Head with 2HP MAKOR Motor with Fan and J1000 Drive.

MAKOR LTSI/6 Profile Sander(6) Stations, 6"Width Capacity (approx), PLC Controller. -- 5.5HP Variable Speed Feed Motor with (6) 6"W Powered Feed Belts. -- 1st Station: Tiltable 3-Point Oscillating Profile Sander, 24" Contact Sanding Area, 2HP MAKOR Motor with Cooling Fan and J1000 Drive. -- 2nd Station: Tiltable 3-Point Oscillating Profile Sander, 24" Contact Sanding Area, 2HP MAKOR Motor with Fan and J1000 Drive. -- 3rd Station: Tiltable Polishing Head 2HP MAKOR Motor with Fan and J1000 Drive. -- 4th Station: Tiltable Polishing Head with with 2HP MAKOR Motor with Fan and J1000 Drive. -- 5th Station: Tiltable Polishing Head with 2HP MAKOR Motor with Fan and J1000 Drive. -- 6th Station: Tiltable Polishing Head with 2HP MAKOR Motor with Fan and J1000 Drive.Dimensions are 20’ L x 5’ W, 8’ H, and weighs approximately 7,000 lbs.

System includes: Vacuum Coater UV Oven with (9) lamps Lateral Transfer Table Max width 9" Able to run clear or pigmented coating

ROTOFAST 10 panel cleaner is designed for automatic cleaning of parts just prior to coating application for a dust-free finish. A rotating brush is combined with air blow-off units and an anti-static bar in order to efficiently clean flat or profiled parts of different shapes and dimensions. KEY FEATURES --Top surface One rotating brush with variable speed and height adjustment --One de-ionizing (anti-static) bar --One group of rotary blowers with timed entry --One group of fixed blower nozzles with timed entry Bottom surface --One group of fixed blower nozzles with timed entry --All components housed in single cabinet with suction hoods --Feed speed adjustable by potentiometer --Rubber pressure rollers to secure parts while brushing --Belt conveyorWeight 600 Kg.

MAKOR Q1 Spray Line including Paint Pumps and Guns:This line was set up with the idea of adding a stack oven after the sprayer in the future if it is required. This line has seen very little use.Station #1: Infeed loading conveyorStation #2: MAKOR Q1 paper belt sprayer 3 circuits plus a cleaning circuit.Station #3: Ppowered roller conveyorsStation #4 (3) three lamp UV oven. Station #5: Outfeed conveyor. The line comes with (2) two paint pumps and (4) four spray guns, the brands GRACO MERKUR and GRACO spray guns. Reciprocating Spray Machine, Makor Q-ONE 1300 with Changeover SystemFlexibility, reliability, and ease of use, combined with limited managing cost and investment, make Q-ONE the ideal machine for companies with low-volume production applying water-based or solvent-based paints, or glues. Even companies switching to automatic coating applications for the first time can realize the advantages of the Q-ONE: Higher production and paint savings, uniform coating, and higher and more consistent quality.Structure and Transport System:The single steel frame guarantees perfect stability and the absence of vibration during the oscillating spraying. A part reading bar is located at the entrance of the machine to detect the workpiece shape to optimize paint consumption. The workpiece transport system consists of a paper belt or plastic film supported by a vacuum belt system makes the machine self-cleaning, eliminating downtime and maintenance costs, but does not allow the recovery of the sprayed productoverspray is prevented from accumulating on the lower side of the workpiece paper roll replacement is quick and easy.Spraying Group:The guns, mounted to oscillating supports, are adjustable to allow optimal orientation of the spraying zone the entire oscillating group is connected to the frame of the machine through pads that guarantee the absolute absence of vibrations, resulting in perfect paint quality on the workpieces, the pressurization of the zone containing the oscillating mechanisms extends its life and requires little maintenance.Four (4) guns can be connected to one of the three (3) coating circuits three (3) high-pressure circuits with recycle for coatings one (1) high-pressure circuit (without return) for solvent. Coating circuits have return hoses for quickly washing the circuit and for the recirculation of paint-standard supply provides two (2) gun holding plates with a quick disconnection system to allow for fast replacement of the spraying unit.Paper Unrolling and Rewinding System:The unrolling system at the entrance and the rewinding device at the exit are designed to maintain constant tension of the paper, avoiding breakage even when it is soaked by the paint, loading and unloading the support rolls are easy due to lateral pull out on wheeled carriers. An independent vacuum hold-down fan enables superior control of the paper belt rewind station and includes a self-adjusting system to maintain a consistently flat paper belt transport

MAKOR Q-ONE Feed Through Spray Machine. -- The Q-ONE sprayer is a single arm Reciprocating System with a paper belt overspray collection; it combines productivity, flexibility, and quick change-over with a limited investment. -- This continuous belt conveyor system, combined with disposable paper promotes a "self-cleaning" machine & dramatically reduces clean-up & service time.Operation: -- Suitable for all types of conventional coatings from solvent to water-based materials; -- Conveyor advances only when parts are present. -- Conveyor system with a vacuum belt to secure & support the feeding of the disposable paper, ensuring proper tracking & automatic winding of the paper roll. -- The paper roll change-over time is only a few minutes. The panel lies flat on the belt which prevents the transfer of over-spray onto the bottom side. -- Spraying enclosure is pressurized via (2) intake fans and filtered by means of dry filters. -- This system allows clean air & maintains a consistent airflow throughout the Spray Cabin, also limiting the machine maintenance time to a minimum and producing an enhanced quality finish, control & containment of over-spray, resulting in significant material economy. Internal airflow is adjustable utilizing inverters. -- Spray system uses an inverter drive and variable speed reciprocating trolley which provides a consistent spray speed & pattern across the entire conveyor belt. Equipped With: -- Spray system with (4) spray guns, mounted on a "Quick-Change" gun support trolley. -- (2) High-pressure lacquer feeding circuits with recycle through a fluid distribution manifold (pre-disposed for (2) additional laquer feeding circuits). -- PLC touch-screen for clear visual operator interface & large memory storage of working programs, parameters, controls & diagnostic functions. Photo diode light bar reads the location and size of part to be sprayed.Technical Specifications: -- Working Width: 0 - 1,300 mm (0" - 51"). -- Feed Motor: 0.75 kW, variable speed control from 2.5 - to 5 MPM (8 - 16 FPM). -- Vacuum Belt Motor: 1.5 kW(2 HP). -- Paper Rewind Motor: 0.18 kW. -- Paper Roll: Dia. 21.5" max. (approx. 9,500 lineal ft.). -- Reciprocator Motor: 2.2 kW. -- Exhaust Fan Motor: 5.5 kW. -- Air Flow: 7,950 CFM. -- Pressurization Air: 2 x 3,900 CFM. -- Total Installed Power: 13 kW.NOTE: Really still like new with Very Low hours !! It's probably still the original roll of paper on the machine.

MAKOR Q-ONE 1300 FEED THRU FLAT LINE SPRAY SYSTEM: -- Features:The Q-ONE sprayer is a single-arm Reciprocating System with paper belt overspray collection; it combines productivity, flexibility, and quick change-over with a limited investment. This continuous belt conveyor system, combined with disposable paper promotes a "self-cleaning" machine & dramatically reduces clean-up & service time.Operation: -- Suitable for all types of conventional coatings from solvent to water-based materials; -- Conveyor advances only when parts are present. -- Conveyor system with a vacuum belt to secure & support the feeding of the disposable paper, ensuring proper tracking & automatic winding of the paper roll. -- The paper roll change-over time is only a few minutes. The panel lies flat on the belt which prevents the transfer of over-spray onto the bottom side. -- The spraying enclosure is pressurized via (2) intake fans and filtered by means of dry filters. -- This system allows clean air & maintains consistent airflow throughout the Spray Cabin, also limiting the machine maintenance time to a minimum and produces an enhanced quality finish, control & containment of over-spray, resulting in significant material economy. Internal airflow is adjustable by means of inverters. -- The spray system uses an inverter drive, variable speed reciprocating trolley which provides a consistent spray speed & pattern across the entire conveyor belt.Equipped With: -- Spray system for (4) spray guns (guns NOT included), mounted on a "Quick-Change" gun support trolley. -- (2) Gun holding plates with "QC" (quick-change) system to allow for fast gun replacement -- (3) High-pressure Coating Circuits with recycling through a fluid distribution manifold + (1) High Pressure Circut (without return) for Solvent. -- Recycling Coating Circuts have return hoses for quick washing the Circut & recirculating of the Coatings. -- PLC touch-screen for clear visual operator interface & large memory storage of working programs, parameters, controls & diagnostic functions. Photodiode light bar reads the location and size of the part to be sprayed. Technical Specifications: -- Working Length: infinite -- Working Width: 25 - 1,300 mm (1" - 51") -- Working Height: 3 - 60 mm (0.125" - 2.375") -- Feed Motor: 0.75 kW, variable speed control from 1 - 6 MPM (3.3 - 19.6 FPM) -- Vacuum Belt Motor: 1.5 kW (2 HP) -- Paper Rewind Motor: 0.18 kW 0.24 HP). -- Paper Roll: Dia. 550 mm (21.6") max. -- Reciprocator Motor: 2.2 kW -- Exhaust Fan Motor: 5.5 kW -- Air Flow: 7,950 CFM -- Pressurization Air: 2 x 3,900 CFM -- Total Installed Power: 13 kWNOTE: Pumps & Spray Guns are NOT included with this system.

Two Bay 52" capacity Pneumatic clamping

2005 Marathon Spray Booth 14' wide x 25.5' long x 8'9" tall Booth only no racks, spray guns, paint pots etc included

MARCON M6000C DOUBLE ROW LINE BORER(2) Rows of (23) spindles on 32 mm spindle centers; up-stroke boring heads w/panel supports & each with 1 HP motor. -- Adjustable from 6"-24-1/2" on double 1-1/8" round supports w/ACME hand wheel screw positioning; drill bits operate individually or both heads at once. -- (2) Spring loaded holddowns; (2) index pins for accurately locating additional holes, 10 mm collets. -- Equipped with: Air/electrical controls, and foot-operated switch.

Marinus Powermax 300 End Matcher HB Precision attachment 400 v (will need transformer in US)

--In auction: https://exfactoryauctions.com/Detail/SH-230492/event/A122024$1 --NO RESERVE!-- MARTIN T 23 Tilting Spindle Shaper, with 30 mm (1.18") Interchangeable Spindle & Power Feeder Specifications: Table size 940 x 1100 x 850 mm (37.01” x 43.31” x 33.46”) H, with Table insert dia. 90, 130, 205, 305, & 480 (3.54”, 5.12", 8.07”, 12.01”, & 18.90”). Spindle tilt 0° to 45°. Maximum capacity under nut 7". Vertical spindle adjustment 145 mm (5.71"). Spindle speeds 3000, 4,500, 6,000, & 90,000 RPM. Equipped with: 6.4/7.8 HP Motor. "MK5" Spindle shaft. Mechanical spindle brake, with Foot pedal. Hand spindle lock. Complete with: 11-1/2” x 4-3/4” Left & Right Fences, with 21” x 6” H Left & Right Wood fences. 1996 CO-MATIC 1 HP 4-Speed 4-Roll Power Feeder, with Speeds 13, 26, 26, & 72 FPM. Dimensions with Power Feeder: 42" x 42" x 63” H.

MARTIN T-71 Sliding Table SawSpecifications: -- 10' Cutting cap., 9.5' sliding table; 3-position table locking mechanism, cast iron machine table, 7.5 HP motor; tilting saw arbor (arbor speed 2,800 - 4,000 & 5,500 RPM) with tilting from 0° - 45.5°, 16" saw blade cap.; 1 HP - 9,400 RPM scoring motor. -- Max. cutting height 5-11/16", hydraulic saw blade height & tilt adjustment by foot pedal control; cutting width between saw blade and rip fence 49". -- Complete with: -- Rip fence with micro-adjust; crosscut fence flip stops.From seller: "It will hold its accuracy and precision as long as you care for it. It will cure all past trauma of inaccuracy from lesser saws. I used this saw to dimension all solid wood parts, cut out sheet goods, cut joinery in the plywood and cut solid wood joinery from furniture scale parts up to timber-framing parts. It will cut 3/4"; wide x 1 1/2"; deep dadoes in a single pass without even flinching."

MARUNAKA Model RD – 8J WIDE Single Deck Veneer Roll Dryer;Complete with the following features: -- 1988 - year of manufacture. --Working width – 51"; --Length of the dryer – 24 Ft (4 Sections) --Type of heating - Steam --Operational in 2018 when mill closed --Professional rigging and loading available.

MARUNAKA Model RD-3UB/RD-6UB (Connected) Single Deck Veneer Roll Dryer;Complete with the following features: -- (3) 3 HP circulating fans with (1) 3 HP exhaust blower thru the ceiling. -- Optional heat source: electric (7) Elements/Zones, computer controlled thermocouples in addition to (2) Natural gas burners (OEM).. Both dryers have a 100amp circuit breaker with 100amp fuses. The RD 8 operates with 4 fan motors and 4 heaters. The RD 6 has 3 fan motors and 3 heaters";.. -- Capable of temperatures to 120° Celsius (250° Fahrenheit). -- Working width 1000 mm or about 39 inches. Veneer is fed endo.Please Note: -- Dryer is (2) separate units; all equipment will fit into a 40' container for shipment from Eastern USA. -- All equipment is in good working condition including all fans and blower, temperature control works properly; feed roll drive works well. -- Rolls have been nickel treated to minimize corrosion/oxidation. -- This dryer equipment is still in place. -- MARUNAKA (2) Models: RD-3UB and RD-6UB currently connected to increase capacity. Can easily be separated.NOTE: Refurbished in 2005, operated from 2005 - 2012. Still operational ready to work!

MASTER MACHINERY MC-MDS-1 Single Spindle ShaperSpecifications: -- Table size: 27.5" x 32" -- Spindle speed: 7500 - 10,000 RPM -- Main motor: 3 HP

MASTERWOOD PROJECT 313 CNC MACHINING CENTER (W/ACT/BORING): -- Specifications:Working Capacity:"X" Axis 3,080 mm (121"), "Y" axis 1,100 mm (43") width; -- Positioning Speed:Programming speed in X-axis 197 FPM (60 MPM), Y-axis 162 FPM (49 MPM), Z-axis 58 FPM (18 MPM). -- Boring unit:(13) independent vertical spindles, (9) in X-axis, (5) in Y-axis; (4) horizontal spindles with (1 + 1) in X-axis for edge boring in the left- & right-hand panel edges. -- Machining:(1) 7.5 HP (5.6 kW) high speed router (1,000 - 24,000 RPM) by frequency inverter; 1.5 HP (1.1 kW), 6,000 RPM grooving saw with manual rotation for X-axis or Y-axis; -- Work Table: (6) moveable support rails with (2) vacuum cups ea., double zero settings, (6) pneumatic backstops and (2) pneumatic side stops creating (2) working zones. -- Operator & Machine Control:TECNOSUD "K68800" Microprocessor control for (3) axis, lineal, circular, and helical interpolation. Equipped with 14" color video graphic monitor, keyboard for data entry, 1.44 MB floppy disk drive, 64K RAM, RS-232 for possible connection to office PC, all mounted in separate free-standing control cabinet; features to run CPL/Parametric "TRIG" programming and "Spline" CAD/CAM. -- Complete with: Dual zone vacuum pump. Ontario Hydro approved electrics. -- Actual Model is MASTERWOOD PROJECT 313

MASTERWOOD OMB1CN3-TF Horizontal Slot Mortiser. One NC working head (3) axis with programmable microprocessor.. Machines a sequence of slots on windows, doors, shutter, or cabinets without moving workpiece. Continuous cycles with loading/unloading. -- Equipped with: (1) Maka style chisel mortising unit, (1) Vertical routing unit and (1) TF Horizontal routing unit. High frequency drilling - routing with controlled axis, DC motors, ball screw driven. -- Max Mortise workpiece size 150x110x2800 mm length, (5.9"x4.3"x110.2"). Vertical and horizontal routers 142"; length. -- Max slot depth 130 mm (5.1"). Max vertical head stroke 140 mm (5.5"). -- Features: Pneumatic hold-downs bar mounted above table. Flip-up pneumatic pressure beam for additional support when needed. Free-standing control and electrical cabinets house computer monitor and keyboard. Master universal electronic system controller (MW CN10 Centromac) -- Vertical routing assembly: 4HP, 220/380v 3 PH, 9,000 RPM -- Horizontal routing assembly 5"; 220/380v, 3 PH, 9,000 RPM -- Memory for 50 cycles. Mirror imaging with preset tool speed (over-writeable knob). -- Total load 21 KVA -- Overall dimensions 4200mm long x1600x1600mm (166"x63x63"). Electrical cabinet 1,000 high x 450x950mm (40"x 18"x38"). Approx. weight 3800 Kg (8,400 Lbs.).