Woodworking Equipment For Sale

HOMAG OPTIMAT KL-75 / A20 EDGEBANDER 0.4 - 20 mm (3/4") Thickness edgebanding cap., 70 mm min. panel thickness.Equipped with: Automatic edge feed magazine for coil, HPL & strip stock; "Hot Melt" glue system with QA34 Quickmelt unit, with reversible glue roll applicator; pneumatically controlled pressure roll section with 7 pressure rollers. -- Workstations: Double motor front & rear end trim, straight & chamfer trimming (0.5 HP - 10,400 RPM ea. motor). -- Top & Bottom rough trims (2 HP - 11,500 RPM ea. motor). -- Top & Bottom fine trims, tiltable 0° - 30° (0.5 HP - 10,980 RPM ea. motor); open space for workstation. -- Adjustable top and bottom glue scraper. -- Electronic Height adjustment for Top pressure beam with double V-belts, 80 mm wide Heavy Duty feed chain w/rubber pads. -- Feed speed variable up to 35 MPM. -- Complete with: SIKO Digital adjustments on T & B Flush and Fine Trim. -- Homatic NC21 Controller, Fixed position Outrigger panel support, insulated sound cabins w/interior and overhead lighting for all trim workstations. -- Includes Owners Manual and the Electrical Schematics.NOTE: Suggested replacement parts needed, as noted by our technician - all the track pads, the hold-down belt, the pressure roller, and likely a glue pot rebuild. Estimated cost for these parts, not including labor is $5600. The replacement of these parts is NOT included in the machine price.

- Min. panel height 0.47 inch - Max. panel height 1.57 inch - Min. edge thickness 0.01 inch - Max. edge thickness 0.24 inch - Max. forward feed speed 82.02 ft/min - Top pressure with rubber belt - No. Panel Sizing / Milling units 2 Pre-milling unit - Lamps to preheat the side of the panel - Edge coil magazine - Gluing system - glue pot for EVA hot melt glue - premelter for EVA hot melt glue - QA65 - Roller set to press the edge - no. pressure roller 7 - with positioning by NC No. Edge Processing Units 6 First Processing Unit - End trimming Constructor model HL81 - no. motors 2 - with positioning by NC Second Processing Unit - top and bottom rough trimming - no. motors 2 - with positioning by NC Third Processing Unit - Multi Function trimming and corner rounding - Constructor model - FK11 - no. motors 2 - with positioning by NC Fourth Processing unit - edge scraping - with positioning by NC Fifth Processing Unit - glue scraping - with positioning by NC Sixth Processing Unit - buffing - no. motors 2 Spray unit Control system Power Touch

HOMAG AMBITION 2274 (KAL 370/6/A3) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.3 - 3 mm (0.011. - 0.118"), Strip material min/max Edge Thickness 0.4 - 1 mm (0.016 - 0.039"),Panel stock min/max thickness 8 - 60 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18").Minimum workpiece width: 2.36" (60 mm) with workpiece thickness ≤ 22 mm) & 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units:Top/Bottom spraying device prior to workpiece pre-milling. Designed for applying a separating agent, for easier cleaning of any residual glue on the panel. -- In-Feed Fence: Pre-heated manually adjustable in-feed fence with digital indicators. -- Pre-Milling Station:(2) 2.2 HP (3.0 kW) - 150 Hz, 9,000 RPM vertical jointing spindle motors; equipped with panel blow-off device and SIKO digital counters for adjustments. -- Panel Pre-Heat Unit: Quartz lamp for heating substrate edge before glue application. -- Edge Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Maximum roll diameter: 400 mm & 830 mm.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System Homag Quickmelt: QA 3 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast five-minute (5) heat-up time. -- Pressure Section: Programmable (Servo), automatic pressure zone adjustment, (1) large 150 mm dia. driven & (4) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Workstations: -- End Trimming Unit:(2) 1 HP (0.8 kW) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. Programmable (Servo). -- Rough/Pre-Trimming Unit:(2) 0.55 kW 0.74 HP (0.55 kW) - 12,000 RPM Motors, tilting range +/- 1° & counter-rotating to machine feed to prevent blowout & .Height adjustment synchronized with the top pressure-beam .With digital counters. -- Profile/Bevel/Corner Rounding Unit:(2) 0.54 HP ( 0.4 kW) - 12,000 RPM, Multi-function Motors to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge.By way of the machine control, this unit adjusts between a radius and a chamfer without a tooling change.Max. feed speed 20 MPM (65.6 FPM) when using "Corner Rounding Unit". -- Profile/Bevel Scraping Unit:Top & bottom for thick PVC/ABS, electro-pneumatic positioning & pneumatically activated. Pneumatically-controlled

HOMAG AMBITION 2274 (KAL 370/6/A3) EDGEBANDER (W/PRE-MILL/HIGH PRODUCTION) (aka "TAPE ROCKET"): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.3 - 3 mm (0.012. - 0.125"), Strip material min/max Edge Thickness 0.4 - 1 mm (0.016 - 0.039"),Panel stock min/max thickness 8 - 60 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). Minimum Work piece length 610 mm(24").Minimum workpiece width: 2.36" (60 mm) with workpiece thickness ≤ 22 mm) & 4.13" (105 mm) with workpiece thickness > 22 mm). -- Cleaning Agent Spraying Units:Top/Bottom spraying device prior to workpiece pre-milling. Designed for applying a separating agent, for easier cleaning of any residual glue on the panel. -- In-Feed Fence: Pre-heated manually adjustable in-feed fence with digital indicators. -- Pre-Milling Station:(2) 2.2 HP (3.0 kW) - 150 Hz, 9,000 RPM vertical jointing spindle motors; equipped with panel blow-off device and SIKO digital counters for adjustments. -- Panel Pre-Heat Unit: Quartz lamp for heating substrate edge before glue application. -- Edge Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Maximum roll diameter: 400 mm & 830 mm.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System Homag Quickmelt GA 65 / QA 65: QA 65 - EVA Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). Ultra-fast five-minute heat-up time. -- Pressure Section: Programmable (Servo), automatic pressure zone adjustment, (1) large 150 mm dia. driven & (4) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Workstations: -- End Trimming Unit PK 25:(2) 1 HP (0.8 kW) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer to straight snip. Programmable (Servo). -- Fine Trimming Unit PF20:(2) 0.54 HP ( 0.4 kW) - 12,000 RPM, fine trimming unit for edge overhangs at the work-piece upper & lower edge.Operator Interface: -- Power Touch Control Multi-Touch Screen Controller on separate console with 21.5" Full HD flat screen display, keyboard and mouse. Functions in Windows environment, includes fault diagnostic, OS9 real-time operating system."WoodScout", included graphic diagnostic tool designed to increase throughput and decrease down time. Graphical PLC diagnosis display of the error location in the machineCustomer-specific data base system that allows the operator to enter the reason for the error as well as the corrective measures to assist with future tro

HOMAG KAL 310/4/A3/S2 EDGEBANDER (W/PRE-MILLING): -- Specifications:Working Capacity: 0.3 - 3 mm Edge thickness cap., min. panel width 22 mm; max. panel thickness 60 mm; Dual speed -- Equipped with: Pre-Milling Unit 3481: (2) motors, 3 kW, 9000 RPM each, pneumatic controlled/jump milling spindles and adjustable, manual with digital indicator in-feed fence. -- Hot Melt Glue System "QA 34" Quick-Melt Unit: with heated glue roller; -- Edge Magazine Unit 2456: Automatic (2) coil/strip magazine, coils 0.3 - 3.0 mm. -- Pressure Section: Pressure roll section with (3) rollers, (1) large dia. driven & (2) idle rollers; with pneumatic pressure control for straight edges -- HOMATIC "NC 21" Power Control System: Controller operates in Windows-XP environment; Keypad w/LCD display, fault diagnostic, etc.; diagnostic analysis from HOMAG service support via Modem. -- Workstations:End Trimming Unit: (2) motors, 0.18 kW - 12,000 RPM each, to cut excess edge on the front & back of the panel. -- Flush/Pre-Trimming Unit 3201: Top & bottom trim station, 0.55 kW - 12,000 RPM +/- 1° angle adjustment, manual positioning with digital counters. -- Fine/Bevel Trim Unit 3216: (2) motors 0.4kW - 12,000 RPM each, manual positioning with digital counters -- Profile Edge Scraping Unit: with electro-pneumatic adjustment -- Buffing Unit 4402: Top and bottom with oscillation. (2) motors, 0.25kW, 2850 RPM -- Complete with & Features:Electronic DC brakes on all trim motors; sound cabin for all workstations. -- Adjustable outboard panel support with swing out arms for up to 800 mm. -- 80 mm Feed track pads; manually adjusted V-groove belt on top pressure beam and Sound/Safety enclosure over workstations. -- Actual Model is HOMAG KAL 310/4/A3/S2Note: This machine has a new display and a new back up one as well!

HOMAG AMBITION 2262 (KAL 210) PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): + LIGMATECH Return ConveyorSpecifications: -- Working Capacity: Coiled stock min/max Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Panel stock min/max thickness 12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence:Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station:Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor; includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, air jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-HeaterPre-heating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures.Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multi-Purpose Magazine:A multi-purpose 6-coil magazine expands capability by running coiled material.Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgeband. -- Gluing System: (EVA - Hot Melt)QA 34 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allow for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/h (26 LBS/h) -- Pressure Section:Manual Adjustment with digital counter, (1) large 160 mm dia. driven & (6) 70 mm dia idle rollers, pneumatic pressure control depending on edge banding material used.WORKSTATIONS: -- End Trimming Unit HL 81:0.8 kW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30 deg. to straight cut. -- Rough/Pre-Trimming Unit:Top & bottom, 0.55 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°.Manually adjusted with digital counters. -- Profile/Bevel/Corner Rounding Unit FK 11:Multi function 0.4 kW (0.54 HP) x 2)- 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge; Servo controlled, Max. feed speed 20 MPM (65.6 FPM). -- Profile/Bevel Scraping Unit:Top & bottom for thick PVC/ABS, pneumatically activated. -- Flat Glue Scraper Unit:Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit:Top & bottom edge buffing/polishing. -- Spraying Units:Top/Bottom spraying device is designed for applying a separating agent, for easier cleaning of any residual

Homag Double End Tenoner System will be available approximately August 1, 2023 Also available with a direct transfer conveyor and [Gabbiani DET](https://www.carolinamachinerysales.com/listings/4073350-used-2003-gabbiani-sqv-sqi-double-end-tenoner) currently running inline.

Homag Espana CH-03/32/32-PLUS Panel Saw Still under power and available for inspection. 230/480 V

HOMAG AMBITION 2240 PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Working Capacity: Coiled stock min/max Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"),Panel stock min/max thickness 12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18") -- In-feed Fence:Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station:Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor.includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, air jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-HeaterPre-heating the panel brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures.Quartz lamp for heating substrate edge before glue application improved edge quality and optimum bonding. -- Multi-Purpose Magazine:A multi-purpose 2-coil magazine expands capability by running coiled material & strips. Magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panelon the edgebanding. -- Gluing System: (EVA - Hot Melt)QA 3 - Quick Melt Overhead Unit & heated roller applicator digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gatesLower melting unit equipped with automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr) -- Pressure Section:Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used.Work Stations End Trimming Unit HL 81:0.8 kW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & Bottom Flush Trimming Unit:Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12:Multi-function 0.4 kW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10:Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit:Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11:Top & bottom edge buffing/polishing, pneumatically activated.Operator Interface: HOMATIC PC 22 Power Control w/Touch Screen:Controller functions in Windows

Homag BST 500

Homag BOF 311/37/15/R CNC Router Specs (to be confirmed): Homag "Vantage 12L" CNC Router Aluminum router table 60" x 144" working area Gridded Pneumatic reference stops Vacuum gauges Foot pedal control Drill unit Nine (9) vertical spindles One (1) horizontal spindle (two outlet) in X axis One (1) horizontal spindle (two outlet) in Y axis Router 16 HP HSK (quick-change) CW/CCW rotation Variable RPM Ten (10) position rotary tool changer Sound enclosure Front safety mats Safety fencing with interlocked access door Controller Flat screen monitor Standard keyboard and mouse Remote control pendant Also included: Laser projecting unit Ceiling mount

Homag BMG 311 Venture 316L CNC

Homag Optimat NBP084/ Vantech 480 4x8 Bed 12 HP Spindle (replaced in 2019) 7-Position Boring (3) Vacuum Pumps Clean Machine

Homag Drillteq V200 Model Optimat BHX 055

Weeke Model Optimal BHX050 Vertical CNC Machine 8 Vertical Drilling Spindels 2 Horizontal Spindle in X-Direction 1 Horizontal Spindle in Y-Direction Grooving Saw in X-Direction 1 Powerful 5kW ETP 25 Routing Spindle Vector Speed: X-30M/Min Y-30M/Min Z-15M/Min

Homag Centateq N300 CNC Router 5x10 Table Offload conveyor Schmaltz overhead gantry system

Homag Centateq N300 CNC Router Infeed system Outfeed table Boring block (2) Vacuum Pumps

Homag Optimat NBP084/ Vantech 480 4x8 Bed 12 HP Spindle 7-Position Boring (2) Vacuum Pumps Clean Machine

Homag Sawteq B300 38/38 Front Load Panel Saw Specifications: Working Capacity: 149.6'' (3800 mm) Rip cutting capacity; 145.6'' (3700 mm) Pull back capacity. Main saw blade projection 3.74'' (95 mm) 28 HP (21 kW) Main saw blade & 3 HP (2.2 kW) scoring blade; Scoring saw adjustment via "CADmatic" control. - Saw Carriage Forward speed 0 - 492 FPM (0 - 150 MPM) Saw carriage reverse speed 0 - 492 FPM (0 - 150 MPM). - Pusher Fence: Electronically controlled overhead program fence with (6) 2-finger gripper clamps; clamps open up to 95mm (3.7"). Rack & Pinion drive on both sides, forward speed up to 296 FPM (90 MPM), return speed of 296 FPM (90 MPM). - Operator & Machine Control: HOMAG "powerTouch2" PC Front-End with "CADmatic 5.0" Operating System "designed for industrial environments"; virtually unlimited cutting dimensions memory. 21" Full HD widescreen "Touch-Screen" monitor with multi-touch display, online operation from an office PC is possible. All mounted into dust sealed, air-conditioned control cabinet. "Real-Time" Cutting sequences with a new 3D assistance graphic supports the operator and is intuitive to operate, which shortens the training period and reduces errors to a minimum. This results in efficient processes and steady output. Simple handling via tapping and swiping (touch functions) with Quick change between the individual sections CADmatic 5.0 is Tapio compatible & open for communication with other machines and software solutions. The SAWTEQ B-300 "IntelliDivide" optimizing software is tapio-ready from installed software or directly from the tapio cloud, allowing "IntelliDivide" to recognize the machine configuration of your saw and take it into consideration for every optimization run in the cloud, completely automatically & you have the choice

HOMAGDRILLTEQ V-200 CNC MACHINING CENTER (VERTICAL/W/BORING): -- Specifications: Flexible "Vertical" Machining Center with "BORING": Uses less than 5 sq. meter of valuable floor space in addition to an innovative panel handling system. -- Working Cap.Max. workable part size for "X" axis is 120" (3,050 mm); "Y" axis 33.4" (850 mm); max. part thickness 3.1" (80 mm).Min. worktable part size for "X" axis is 7.8" (200 mm); "Y" axis 2.75" (70 mm); min. part thickness of 0.31" (8 mm). - Automatic infeed & outfeed from the LH or RH side. -- Positioning SpeedThe "V-200" can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axis & 50 FPM (15 MPM) in "Z" axis with total safety, providing an unmatched working capacity. -- Boring Unit(1) 3 HP (2.3 kW); Variable speed from 1,500 - 7,500 RPM motor; (13) independent spindles with: (8) spindles in "X" axis & (5) spindles in "Y" axis.(6) Horizontal spindles with (2 + 2) in "X" axis & (1 + 1) in "Y" axis; boring block has "QUICK CHANGE" spindle system. -- Operator & Machine ControlHOMAG "POWERTOUCH" + Windows + WoodWOP Operating System; "IntelCore 2 DUO" Processor.21" TFT Monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; (1) 1.44 MB floppy disk drive, (1) CD RW drive, modem, Ethernet connection.Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible. -- Complete with:Pneumatic part clamping devices; sound enclosure and complete set of safety devices. -- Options Include:(1) "X" Grooving Saw; 9,000 RPM, max. saw blade dia. 100 mm.(1) 12 HP (9 kW) Electro Spindle router with manual Quick-Change adaptor; variable speed from 6,000 - 24,000 RPM. -- Actual Model is: HOMAG DRILLTEQ V-200 OPTIMAT BHX 055.