Woodworking Equipment For Sale

CANTEK MODEL CFS100 / EM-12 DEFECT SAW AND END-MATCHING SYSTEM:Consisting of a CANTEK model "CFS-100" Optimizing Cut-Off Saw followed by a CANTEK Model "EM 12" Through-Feed End Matcher and with the following specifications and features: CANTEK "CFS-100" OPTIMIZING CUT-OFF SAW -- Up to 20 mm X 200 mm or 100 mm X 100 mm( 3/4" X 7.87" or 3.9" X 3.9" cutting capacity with 18" x 30 mm bore sawblade is driven by a 10 HP motor driving the saw spindle at 3,200 RPM; 2.7 HP servo drive feed system drives the stock up to 260 FPM; 0.787" min. distance between crayon marks; requires 75 to 80 PSI at the saw and 100 to 120 PSI at defect blow-off station. Machine comes completely wired and programmed. -- Machine is ideal for separating crayon marked waste zones from useable material before entering into a feed-thru End Matcher; provides (3) times greater production than manual cut-off saws.5% + Material recovery (yield increase) over manual cutting; compact and user-friendly design; controller adopts an industrial grade computer that employs a 32-bit floating-point DSP system and features flash and battery backup SRAM for double security; superior to conventional PC-based controls, it can fully eliminate the machine going down or being damaged due to a poor environment, such as, unstable voltage, high temperature, sawdust, etc. -- With defect blow-off system combined with computerized logic control permits the blow-off time and the length of defect to be set as desired; provides efficient defect removal and eliminates defects from bumping against the sawblade, resulting in the machine going down or sawblade damage. -- Computer control provides easy and fast maintenance; feed system driven by a servo motor for fast and accurate motion and position control; max. feed speed up to 260 FPM; cutting rate up to 80 cuts per minute with cutting accuracy within approx. ±1mm / 0.40"; control employs a touch screen for easy learning and operation.Features: -- New machine design features maximum maintenance convenience; high quality electric components provide maximum dependability; safety guards for maximum operator protection; 48" long infeed table standard - longer available option; 18" carbide blade included.(5) Cutting modes include: -- Adjustable end cuts to a max. of 10mm (0.4") -- Fixed length of cutting mode. -- Sequential cutting mode with (10) sets of cutting sizes held in memory (for sequential cutting mode only). -- Cutting on fluorescent marks with double-end trimming (perfect solution for end matching). -- Reading fluorescent marks with double end trim, fixed-length, random length end match, and finger joint block cutting. CANTEK "EM-12" END MATCHER -- Continuous through-feed system; handles random length min. 10.6" to any length x 0.4" to 1.38" thickness x 12" width capacity; -- 295 FPM max. feed speed; average speed of 75 FPM based on 6'-6" board lengths; with 118" infeed and 98" outfeed tables; -- 5.5 HP Shaper motors, 1 HP feed motor an

CANTEK EM-12 End Matcher;1.6" to 12" Width x 0.4" to 1.38" thickness (to 2-1/4" optional) x 10.6" min. length capacity. Unlimited lengths possible.Specifications: -- Feed speeds to 295 FPM with approximate production speeds of 77 FPM (based on 6-1/2' incoming boards). -- Standard 173" long infeed table and standard 86" (2,200 mm) long outfeed table; -- (2) 10 HP cutterhead motors with 40 mm spindle diameters; 1 HP feed motor; 1/2 HP motor drive to cutterhead carriage; clamping pressure from top and side; 24 volt DC controls.Standard equipment and Features: -- Designed for machining tongue & groove with or without V's on flooring and panel products; designed to be used for finger joint cutting. -- Heavy-duty self supporting main frame; compact design requires minimum floor space.Feedworks: -- Capable of processing material as short as 11" to an unlimited length; variable speed through-feed systems is controlled by frequency inverter; through-feed system allows the tongue to be cut simultaneously on the tail of one board and the leading edge of the next board. -- Powered top Urethane rolls and spring loaded bed rollers feed the material into position for processing. -- Pneumatic side pressure ensures the material is held square against the fence.Complete with: -- Safety and noise reduction enclosure; convenient touch screen control is used to quickly activate and adjust the machine functions. -- Powered 176" long infeed conveyor is included (additional length optional); with a 86.6" long outfeed table (additional length optional). -- Includes: (2) Individual Precision Insert Tooling Heads as Supplied with Machine & stacked to make (1) pair of heads; set of heads provided for groove on left and tongue on right.

CANTEK TA-14 Tilting Arbor Table Saw. -- Heavy-duty cast iron table precision ground for accuracy. -- Rugged machine frame construction provides maximum stability and reduced vibration. -- 14" Blade capacity. and 0° - 45° tilting arbor. -- 7.5 HP Motor with double V-belt drive. -- Rip fence for a 50" max. cut with a precision Rip fence. -- 48" x 38" Cast iron table. -- Blade guard, miter gauge, push button controls. -- Parts list & operation manual.

CANTEK 1214 TABLE SAWHeavy-duty cast iron table precision ground for accuracy. -- Rugged machine frame construction provides maximum stability and reduced vibration. -- 14" Blade capacity. and 0° - 45° tilting arbor. -- 10 HP Motor with double V-belt drive. -- Rip fence for a 50" max. cut with a precision Rip fence. -- 48" x 38" Cast iron table. -- Blade guard, miter gauge, push button controls. -- Parts list & operation manual.

Non-Oscillating Edge Sander with end sanding kit. -- 6" Wide x 108" long belt. -- 6" x 40" Graphite covered platen. -- 1 HP -1.5 HP, or 3 HP -2 HP, 3-Phase motor w/magnetic switch. -- 7" Diameter drive pulley. -- 7-3/4" x 37" Front table with a 6" vertical adjustment. -- End table for radius work with a 6" vertical adjustment. -- Heavy laminated tables, fabricated steel base and swing-away dust hood.

CANTEK - SS512TB Tilting Spindle ShaperSpecifications: --Tilting spindle from -5° to +45° and 6" x 43" fence. --1-1/4" interchangeable spindle is standard (other sizes available). -- Large cast-iron table is ground and polished for maximum stability and durability. -- Powerful 7.5 HP motor for even the most demanding profiling work. -- Five spindle speeds can be easily adjusted to suit your tool diameter. -- 5-1/2" Useable spindle length, above table 13-¼"; below table 8-¼". -- Electronic spindle brake for added safety and facilitates fast changeover. -- Precision fence assembly with micro-infeed and outfeed fence adjustment. -- The finger-style fence allows the fence to be adjusted around the cutter for added safety and workpiece stability. -- Table size 31 ½"; x 39.4″. -- Dust port (1) 5″ on guard, (1) 4" into the table.

CANTEK LBS300-5S 3-Sided Moulding Sander5-Head Brush Sander, 11" width and 4" height cap., for 3-sided sanding of linear profiled material. Head Configuration: -- (2) Sets of Top abrasive brushing heads with variable speed adjustment by inverter, 0.75 HP (0.55 kW) motor each. -- (1) Left side head, adjustable up/down, in/out, and can be set on an angle, 0.5 HP (0.37 kW) motor. -- (1) Right side sanding head which can be adjusted up/down and in/out, 0.5 HP (0.37 kW) motor. -- (1) Left side sanding head is adjustable up/down, in/out, and can be set on an angle, 0.5 HP (0.37 kW) motor. -- Brush head spindle speed adjustable from 200 - 1,200 RPM. -- Variable feed speed of 6.5 - 27 FPM, adjustment by frequency inverter.Features & Specifications: -- Min. workpiece length 26", min. workpiece thickness 3/8". -- 0.25 HP (0.18 kW) Conveyor motor, 0.33 HP (0.25 kW) moving brush head motor. -- Depending on the application, brushing heads can be cleaning brushes or abrasive cloth brushes. The dovetail pocket design allows for easy abrasive/brush replacement. -- Centralized control panel for operator convenience integrated into machine base.Also available in 460V, 3-Ph, 60 Cy (factory order only – app 10-12 weeks)

Cantek E6 Oscillating Edge Brush SanderIdeal for sanding the edges of cabinet doors, stair treads, or furniture components.Brush abrasive can sand into profiles or break the edges.Oscillation ensures optimum usage of the abrasive and ensures a quality sanding result. -- Adjustable spindle height for maximum usage of the abrasive. -- Adjustable & removable back fence for linear or curved sanding --Variable speed sanding head. -- Magnetic starter with emergency stop button. -- Built in dust hood -- Comes with 1 (one) set of 150 grit abrasives

CANTEK SRS330 Straight Line Rip Saw;Features: -- Very Rigid machine body with a welded steel frame with an integral cast & machined table, which is fitted with a sturdy cast column & saw unit. -- Excellent precision work accuracy and durability. -- Absolute straight line feeding up to 13 ft. of ripping. -- Precision caterpillar chain and double "VEE" extra long (47.2";) guide rails are made of special cast iron the chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Holddown rolls (6 rows).Specifications: -- Max. work piece thickness 4.33". -- Min.work piece length 8". -- Distance between saw and column 18.1". -- Saw arbor dia. 1" and Saw blade dia. 10"; - 14". -- Saw arbor speed 4,300 RPM. -- Useable Chain Length 47";. -- Glue line guarantee 13’ (+/- 0.0098"; or 0.25 mm). -- Feed speeds variable 30 to 130 FPM. -- Arbor motor 20 HP -- Feed motor 2 HP -- Table size 36.6" x 64.6, Table height 31-7/8". Utilities: -- 230 V = 60.8 Full Load Amps. -- Electrics 460/3/60 = 30.4 Full Load Amps. -- Dust Collection Outlet 4"; -- Net weight 3,190 Lbs.Available Options: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03) -- Extra Saw Blade: 14";x0.157"; kerf x 1.5"; bore x 60T (CANC14RS-BLADE-14)

CANTEK R-18 Heavy Duty Straight Line Rip Saw "Cuts From The Bottom"Equipped with & Features: -- Extra Heavy Main Frame Throughout with large support table. -- 6"; Minimum length with this type of saw the blade is cutting downwards, forcing the Blade onto the chain – hence max. stability and safety are realized. -- Better chip clearance for shavings on deep cutting. -- Glue Joint Range – 12"; to 10 Ft.Specifications: -- Depth of Cut 4.7"; (120 mm) max. -- Split chain – double track with HRC60 Rockwell Hardened Guideways. -- 26"; (660 mm) Saw to Column. -- (8) Press Rolls hold material firmly on the track. -- 20 HP Main Motor. -- 3 HP Feed Motor. -- Feed Speed 42 to 164 FPM variable. -- Automatic chain and track Oiler -- 41"; Length of chain above table -- Saw Arbor Height adjustable -- Max. 18"; Blade Diameter x 2"; Bore Dia. saw Arbor with 14 mm pin at 6 5mm centers.Complete with: -- Saw Arbor Brake Included -- Anti-kickback fingers top and bottom -- Dust collection outlets: Top 4" (100 mm), Bottom 6"; -(150 mmm). CFM Required: 1,400 CFM. -- Table Dimensions: 78-3/4"; x 40"; x 33.5"; high (Can be added to optional) -- Net weight - 4400 Lbs. -- Stock Machine Electrics 460/3/60 to UL/CSA Standards (Other voltages available on request)Note: The advantage of cutting from below on thick material, the gullet of the sawblade projects above the stock to clear the shavings halfway through the cut

CANTEK - C 12 RSH, ...Straight Line Rip Saw:Ruggedly constructed with cast iron & ground tables, cast iron pressure housing with (6) guide rollers, and solid welded steel base chassis.Specifications: -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", saw arbor speed 4,400 RPM. -- 16 HP Saw arbor motor, 2 HP feed motor, 45 - 120 FPM variable speed range. -- Min. workpiece length 8", max. cutting thickness 3-3/8", -- Distance from column to center of chain 18". -- Table size is 39" x 57", table height 31-1/2".Equipped with & Features -- The cast iron upper pressure housing provides a stable mounting for the precision ground & nickel chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- 1-Piece cast iron chain with a diamond-cut surface for positive material feeding.

CANTEK C10RSStraight Line Rip SawSpecifications -- 12" Over cutting Rip Saw ruggedly constructed with cast iron & ground tables, -- Cast iron pressure housing with (6) guide rollers and solid welded steel base chassis -- Saw blade dia. 8" - 12", -- Saw arbor dia. 1", -- Feedspeeds of 50, 65 and 85 FPM - 4,500 RPM, --10 HPsaw arbor motor; 1 HP feed motor, --Min. workpiece length 8", max. cutting thickness 3-3/8", --13 3/4" distance between saw and column, -- 30" X 50" table size, 31-1/2" table height.Equipped with & Features: -- Cast iron upper pressure housing provides a stable mounting for the precision ground & nickle chrome steel saw arbor and can be easily adjusted by hand wheel for thickness changes. -- (1)-piece cast iron chain with a diamond cut surface for positive material feeding.Included: Manual , and several blades and the toolkit.

CANTEK C-14RS Straight Line Rip Saw; Absolute straight line feeding Rip Saw. Rigid machine body consists of a thick welded steel frame with an integral table which is fitted with a sturdy cast column. Excellent precision work accuracy and durability.Specifications: -- 4.92" Max. thickness cap; 8" min. length; variable feed speeds from 50 to 120 FPM and powered by a 1 HP feed motor. -- 1" Dia. saw arbor powered by 20 HP arbor motor; swings 12" thru 16" dia. blade at 4,500 RPM; with 24" distance from blade to saw column. -- 31-7/8" From floor to top of table; table is 50" wide x 75" long.Feed System & Chain: -- Precision caterpillar chain and double "VEE" guide rails are made of special cast iron. The chain connecting pins are made of high grade steel - heat treated & ground for high durability and low wear. -- (8) Hold-down rolls for increased control and precise straight line cutting (6 rows). -- Mechanical operation Chain Oiler (Best) provides consistent lubrication to the chain track and automatically adjusts to your feed speed. When oil runs out the machine track stops running to avoid damage to track. Features: -- Precision Built Saw Arbor constructed of nickel chrome steel, large diameter, accurately ground and dynamically balanced. The arbor runs in precision angular contact type ball bearings (eliminates any radial run-out & axial thrust) - V-Belt driven from below, with easy to access adjustments and controls. -- (3) Sets of anti-kickback fingers; (2) top and (1) set in the table. -- Soft start - Star Delta starter. Telemecanique U/L magnetic starters.Options available at additional cost: -- 20mW Red Laser (FPIMLC1320WFL) & Laser Holder (FPICAN03)..................................... $ 495.00 -- Extra Saw Blade: 14";x0.157"; kerf x 1.5"; bore x 60T (CANC14RS-BLADE-14)........... $ 118.00

CANTEK SS512CSB Heavy Duty Production Shaper with Sliding Table & Spindle Brake7.5 HP Features: -- Cast iron sliding table runs on ball bearing for smooth table transition. -- Cast iron ground & polished table with insert rings; table size: 31- ½"; x 39.4″. -- Precision ground and electronically balanced spindle. -- V-belt drive with (5) feed speeds is easily accessed from the front of the machine. -- Electric spindle brake for added safety. -- Spindle lock - with limit switch safety, machine will not start with lock engage. -- Micro spindle height adjustment with dial indicator. -- Interchangeable cutter spindle. -- Forward/reverse spindle rotation. -- Adjustable "finger" type fence Independent micro-fence adjustment on both sides. -- Includes the following standard equipment: 1- 1/4" Spindle, (1) 5"; dust chute on guard & (1) 4"; dust chute in the table, safety guard, Miter tenon jig, and Telemecanique magnetic controls.Net weight 1034 Lbs. Machine dimensions 48.4"; x 39.4"; x 52 ¾";. Shipping weight 1166 Lbs.Shipping dimensions 45 ¼"; x 37"; x 41";

CANTEK SS-512TSB Tilting Spindle and Sliding Table Shaper:7.5 HP - 3-Phase motor, overall table dimensions 31.50" x 39.40", sliding table 10.25" x 39.40". -- Spindle stroke 7"; 1-1/4" dia. spindle with 5 MT receiver and 4-3/4" cap. under the nut. Spindle tilts -5° & +45°. -- (5) Spindle speeds: 3,000, 4,000, 6,000, 8,000 & 10,000 RPM.Complete with: Spindle reversing switch, micro-adjustable fence 6" x 43", thermal overload protection and dust hood.16 weeks delivery.

CANTEK MX340 Edgebander (Single Phase)The MX340 from CANTEK is designed to be a compact, and durable edgebander. -- This machine is equipped with end trimming, flush trimming, PVC scraping, and buffing. -- The CANTEK MX340 Edgebander is operated through a PLC control system with an LED display and keypad.Specifications: -- The MX340 handles panel thicknesses of 0.315" up to 1.77" (8 mm to 45 mm). -- The coil feed accepts edgebanding from 0.4 mm to 3 mm thick, and strip material can be hand-fed. -- Conveyor feed speed is 29.5 FPM (fixed).Work stations: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Pneumatically operated guillotine for up to 3 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit 0.3 HP motor. -- Double top and bottom trimming units (2) 1/2 HP motors. -- Top and bottom scraper/radius scraper. -- Top and bottom buffing station (2) 0.16 HP motors.

102" Width cap. Veneer Clipper completely reconditioned to modern mechanical and safety standards to meet todays manufacturing needs. Original machine frame will be fully disassembled cleaned and repainted. The frame is the only part of the original machine used and all components are upgraded.Mechanical upgrades include:1. 2-Hand anti-tie back push button cycle activation 2. Photo safety eyes located on both front and back side of blade3. Full safety guarding including a fully enclosed knife section 4. New electric motor and gear box main drive system5. New knife and shear bar6. All new electrical/control box with Components and Wiring7. All new upgraded bearings including replacing Babbitt bearings Machine comes with a full (1) year warranty

CARGATE D-860 Rotary Veneer Lathe, Heavy Duty: -- Built specifically to handle large diameter logs as well as small logs. It has a log length capacity of an easy 8'-6" and a diameter capacity of up to 5', peeling down to perfect 4" cores for optimal log utilization. -- This moneymaker looks like a big brother to a Premier Lathe. It comes complete with beefy Bull Gears and boasts plenty of output capacity along with the following main features and components:Specifications: -- BRUNETTE MACHINE WORKS Hydraulic Retractable Spindles - 4" inner, 8" and 11" outer. These are the same spindles as are utilized on a Premier Lathe. -- The spindles are driven by angle-cut 72" diameter Oil-Bath Bull Gears. (This is actually identical to an upgrade to Premier lathes still running.) -- Factory Hydraulic Backup Roll. (This backup roll rides on adjustable rollers riding down on top of the carriage. This prevents backup roll from pushing excessively hard against the core. It produces perfect 4" cores).Equipped with: -- DURAND Charger and Pumps (self centering). -- Factory Log Deck - Complete with S-drive and Gearbox. -- Factory Air Trash Gate, Infeed Conveyor (infeed to chipper). Infeed to PRENTICE Air Bag Clipper, Timing Wheel and Holddowns. -- Factory 5' Wheel, 6-knife, Veneer Chipper with Hold-down Drum Roller, and S-drive complete. -- 6' FERANO Chip Screen and Conveyor. -- Steel Framework and 450 FPM plus uniwind speed!Highlights & Background: -- This lathe is capable of peeling very high production. In 1967 it was actually regularly peeling 225,000 sq. ft. 3/8 basis, or 400 - 500 cubic meters per 8-hour shift. The lathe is in wonderful overall condition and portions can be turned on today although it has not seen service since 2005. When you think "CARGATE" think "big PREMIER" and you will have the right idea.Price shown is in US Dollars. - Experienced Owner is flexible to assist in removal and perhaps installation.

Owner has changed gears and is no longer needing equipment. Great working condition and ready to be shipped.

2016 Casadei Flexa 47 Edgebander 230 V/3 PH