Woodworking Equipment For Sale

The Vantec Veneer Auto Stacker, ELV 1.82B is a Vacuum stacker for 2800 mm Veneer lathe. It is fitted with double stacking system (04 bins), with four veneer transport lines and four 5hp exhausters. with of two stoppers and eight ejecting arms. With drive Panel, VSD for exhaust fans and hydraulics lifting tables. Min veneer sheet length sheet: 2300 mm; • Max veneer sheet length sheet: 2700 mm (or Two sheets of 1350mm); • Min veneer sheet width: 800 mm; • Max veneer sheet width: 1500 mm; • Max height of stacks: 1000 mm; • Exhaust motor: 10 hp 4P (8x); • Inlet conveyor motor: 2hp 8P; • Transport conveyor motor: 6hp 4P; • Hydraulic pump motor: 5hp 4P (3x);

VANTEDGE MM 6.0 9 C-MOTION Edgebander with Pre-milling & Corner Rounding (EVA & POLYOLEFIN adhesive ready).Specifications: -- 10" Color Tough Screen PLC. The PLC controls all work units and the adhesive thermostats with 1-touch Icon Programmable selections, Photo Indicator Alarms to easily troubleshoot, and Swivel Control Panel.Tape and Panel Infeed System: -- 750 mm Coil support table, heavy-duty large solid polished steel panel in-feed fence guide system, Large industrial digital adjustment for the Pre-Mill panel material removal amount. Top Pressure Beam Adjustment: -- Automatic adjustment from the PLC control, Red LED panel feed indicator light for correct panel spacing, Pneumatic Pop Up Stop system -- Working Capacity: Edgebanding thickness, 0.4 - 3 mm capacity. Min. panel width 85 mm (3.3"); min. panel length 125 mm (4.9"); panel thickness 10 - 50 mm (0.39" - 1.96"), Edge Height 55 mm (2.2").Equipped With: -- Dual 3 HP Pre-milling Motors w/Diamond Cutter Heads, Misting Unite w/Large Dual Dust housing ports to help clean the Pre-Milling system, quick change Glue Reservoir and Pressure Section/Infrared Heat Lamp system; consists of Heavy Duty Guillotine to cut 3 mm coil materials, (4) pneumatic polished Pressure Rollers with manual digital adjustment to edge thickness, (1) Rubber Infeed Tape Roller, (1) Metal Infeed Tape Roller; Direct Universal Drive system - NO Chains. Unit with "Auto-set" automatic intervention, Strip & Coil Edge magazine, automatic shear type guillotine. -- Hot-Melt Glue System: Teflon-coated glue pot, digital thermostats with automatic kick-down when the machine is in idle mode.Workstations:End Trimming Unit: -- Dual 0.5 kW (.67 HP) high-frequency End Trim motors on precision "Auto Lube" Linear Guideway. 90 to 10° pneumatic tilt cut adjustment. Electronic sensors to safely monitor motor positions. Thumb screw pneumatic adjustments for simplicity. Tilting Super Finish Top & Bottom Trimming Station: -- Dual High Frequency 0.65 kW (.75 HP) motors with Combi Finish insert tooling, Top Servo-driven positioning of motors for different edge trimming profiles & positions. Corner Rounding Unit: -- Motors on precision billet aluminum swing tracer arms with pneumatic guidance and Face Copy system. The (2) independent motors can be adjusted to match tape thickness via digital scales. Profile Scraping Unit: -- Top, Bottom & Side Copy wheels to properly follow your panels edge, Triple Copy System for panels with blind Dados & Hinge cup holes., digital adjustment for fine-tuning the unit to the proper tape thickness. -- Flat Scraping Unit: Large copy wheels, Insert tooling, adjustable panel spray mist cooling & cleaning system for special materials and composites, adjustable dual Buffing Wheel system, Dual Hot Air Blowers. Buffing Unit: -- Top & bottom Buffing Unit, 0.5 HP (0.37 kW) - 2,800 RPM motors), units tilt 0° - 30°.Complete With: -- Insulated sound enclosure overall trim stations with a split dust hood,

//This machine is in an Auction on exfactoryauctions.com// //Link to machine: http://exf.ac/i5h VANTEDGE MM 6.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): + EVA & Polyolefin Adhesive ready. Specifications: Working Capacity: Edgebanding thickness 0.4 - 3 mm coil stock capacity & 10 mm strip capacity. Min. panel width 85 mm (3.3"); min. panel length 125 mm (4.9"); panel thickness 10 - 60 mm (0.39" - 2.36"). Tape and Panel Infeed System: 750 mm Coil support table; adjustable track feed speed 14, 16 & 20 MPM (66 FPM). Heavy-Duty large solid polished steel panel infeed fence guide system. Large industrial digital adjustment for the Premill panel material removal amount. Top Pressure Beam Adjustment: Automatic adjustment from the PLC control; pneumatic Pop-Up Stop system. Red LED panel feed indicator light for correct panel spacing. Equipped with: Dual 3 HP Pre-milling motors w/diamond cutter heads; pneumatic "JUMP In/Out function. Misting unit prior to Pre-milling; large dual dust housing ports to help clean the Pre-milling system. Quick change Glue Reservoir for EVA & PO glues; Pressure Section/Infrared Heat Lamp System. Heavy-Duty automatic shear type Guillotine with: "Auto-Set" automatic intervention for strip & coil materials. (4) Pneumatic polished Pressure Rollers with manual digital adjustment to edge thickness. (1) Rubber infeed Tape Roller, (1) metal infeed Tape Roller; direct Universal Drive system - NO Chains. Teflon-coated glue pot; digital thermostats with automatic kick down when the machine is in idle mode. Workstations: End Trimming Unit: Dual 0.5 kW (0.67 HP) high frequency End Trim motors on precision "Auto Lube" Linear Guideways; 90° to 10° pneumatic tilt cut adjustment. Electronic sensors to safely monitor motor positions; thumb screw pneumatic adjustments for simplicity. Tilting Super Finish Top & Bottom Trimming Station: Dual High Frequency 0.65 kW (0.75 HP) motors with Combi Finish insert tooling.Top Servo driven positioning of motors for different edge trimming profiles & positions. Corner Rounding Unit: Motors on precision billet aluminum swing tracer arms with pneumatic guidance and Face Copy System. (2) Independent motors can be adjusted to match tape thickness via digital scales. Profile Scraping Unit: Top, bottom & side Copy Wheels to properly follow your panels edge. Panel Nesting System: Triple Copy System for panels with blind dados & hinge cup holes. Digital adjustment for fine-tuning the unit to the proper tape thickness. Flat Scraping Unit: Large copy wheels. Buffing Unit: Top & bottom Buffing Unit; 0.5 HP (0.37 kW) - 2,800 RPM motors; units tilt 0° - 30°. Dual Hot Air Blowers: To re-embellish edge materials. Operator Interface 10" Color touchscreen PLC with swivel Control Panel. The PLC controls all working units & the adhesive thermostats with 1-touch icon programmable selections. Photo indicator alarms to easily troubleshoot errors/issues. Complete with: I

VANTEDGE MM 6.5 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): + EVA & Polyolefin Adhesive ready. -- Specifications: Working Capacity: Edgebanding thickness 0.4 - 3 mm coil stock capacity & 10 mm strip capacity.Min. panel width 85 mm (3.3"); min. panel length 125 mm (4.9"); panel thickness 10 - 60 mm (0.39" - 2.36"). -- Tape and Panel Infeed System:750 mm Coil support table; adjustable track feed speed 14, 16 & 20 MPM (66 FPM).Heavy-Duty large solid polished steel panel infeed fence guide system.Large industrial digital adjustment for the Premill panel material removal amount. -- Top Pressure Beam Adjustment: Automatic adjustment from the PLC control; pneumatic Pop-Up Stop system.Red LED panel feed indicator light for correct panel spacing. Equipped with: -- Dual 3 HP Pre-milling motors w/diamond cutter heads; pneumatic "JUMP In/Out function.Misting unit prior to Pre-milling; large dual dust housing ports to help clean the Pre-milling system.Quick change Glue Reservoir for EVA & PO glues; Pressure Section/Infrared Heat Lamp System.Heavy-Duty automatic shear type Guillotine with: "Auto-Set" automatic intervention for strip & coil materials.(4) Pneumatic polished Pressure Rollers with manual digital adjustment to edge thickness.(1) Rubber infeed Tape Roller, (1) metal infeed Tape Roller; direct Universal Drive system - NO Chains. Teflon-coated glue pot; digital thermostats with automatic kick down when the machine is in idle mode.Workstations: -- End Trimming Unit: Dual 0.5 kW (0.67 HP) high frequency End Trim motors on precision "Auto Lube" Linear Guideways; 90° to 10° pneumatic tilt cut adjustment. Electronic sensors to safely monitor motor positions; thumb screw pneumatic adjustments for simplicity. -- Tilting Super Finish Top & Bottom Trimming Station: Dual High Frequency 0.65 kW (0.75 HP) motors with Combi Finish insert tooling.Top Servo driven positioning of motors for different edge trimming profiles & positions. -- Corner Rounding Unit: Motors on precision billet aluminum swing tracer arms with pneumatic guidance and Face Copy System. (2) Independent motors can be adjusted to match tape thickness via digital scales. -- Profile Scraping Unit:Top, bottom & side Copy Wheels to properly follow your panels edge. -- Panel Nesting System: Triple Copy System for panels with blind dados & hinge cup holes.Digital adjustment for fine-tuning the unit to the proper tape thickness. -- Flat Scraping Unit: Large copy wheels. -- Buffing Unit: Top & bottom Buffing Unit; 0.5 HP (0.37 kW) - 2,800 RPM motors; units tilt 0° - 30°. -- Dual Hot Air Blowers:To re-embellish edge materials. Operator Interface10" Color touchscreen PLC with swivel Control Panel.The PLC controls all working units & the adhesive thermostats with 1-touch icon programmable selections.Photo indicator alarms to easily troubleshoot errors/issues. -- Complete with: Insulated sound enclosure over all Trim Stations with a split dust hood, viewing windows, and industrial lights.Panel jo

Brand new never used!! 16’8” long 22” wide 19” height (adjustable)

VIET - S2-321-HP/KRT, ...3-Head Planer Sander3-Head Planer/Sander 43" with: Planer, Drum and Combi-HeadSpecifications: -- Max. operating width: 1,100 mm (43") -- Min/Max thickness: 3 mm - 160 mm (1/8" to 6.3") -- Working Height: 900 mm (36") -- Abrasive Belt dimension: 44" x 103" -- Feed speed: 3 - 16 MPM (9-3/4 - 52 FPM) -- Rubberized drum: 30 HP Motor -- Combination head with drum & platen; driven by the same motor as the sanding drum -- Extended infeed & outfeed roller -- Planer head with helical insert knives: 30 HP Drive motor

VIET - S211 R+ KRT, 2-Head Wide Belt Sander43" Width. cap.: Drum and Combination head.Head Configuration:1st Head: 160 mm 6.3″ Helical grooved rubber drum. 25 HP motor2nd Head: 160 mm (6.3") Helical grooved rubber drum with a platen combination head., 25 HP motorSpecifications: -- Each heads are powered by a 25 HP motor. -- The heads can be programmed to pneumatically raise & lower along with the platen and do (3) sanding combinations (with the twist of a button). -- Digital height readout and a calibration unit to the left side of the conveyor. -- Conveyor speed is controlled via a variable frequency drive 2.5 HP . -- Max width: 43″. -- Max. height: 6-1/4". -- Variable speed conveyor belt drive from: 3 - 16 MPM (11 - 52 FPM).Equipped with & Features: -- Both heads are equipped with: 1,130 x 1900 mm (44-1/2" x 75"). -- Roller & pressure shoe holddowns. -- Pneumatic tension of sanding belts and feed conveyor. -- Load meter on main motor. -- Disc brake on main motor. -- Emergency stops front & back. -- Roller table extensions front & back.NOTE: This is an extremely low-hour 2012 BIESSE Viet S1 dual head 43″ calibrating Wide Belt Sander.

Viet Opera 5-4.3 RRRR, (4) Head Wide Belt SanderCalibrating Sander (89 Hours)53″ wide cap. - Drum, Drum, Drum, DrumHead Configuration1st Head: 9″ Helical grooved steel drum powered by a 22 kW or 29.5 HP motor.2nd Head: VARIABLE SPEED (via VFD) 9″ helical grooved rubber drum powered by a 18.5 kW or 25 HP motor. 3rd Head: VARIABLE SPEED (via VFD) 11″ helical grooved rubber drum powered by a 15 kW or 20 HP motor. 4th Head: VARIABLE SPEED (via VFD) 11″ helical grooved rubber drum powered by a 15 kW or 20 HP motor.5th Station: Dust brush powered by a 1.27 kW or 1.7 HP motorSpecifications -- The durometer does get softer from head 2 to 3 and then from head 3 to 4. -- It has 53″ width capacity and a 200 mm or 7.87″ thickness capacity. -- Right above the machine's infeed, you will find inspection LED lighting, a digital thickness calibration unit, and a wireless Mitutoyo Digimatic Caliper that communicates with the Opera’s operating system. -- The vacuum bed is powered by an 11 kW or 15 HP blower under the sander to save space. -- The feed mat is powered by a 5.5 kW or 7.5 HP motor with variable speed via a VFD with feed speeds from 9.8 to 52.4 FPM.Equipped with & Features -- Inside you will find interior LED lighting while all the controls on this Opera are upfront via a touch screen -- Constant pass lineNOTE : This calibrating sander has a total of 1,982 power on hours and ONLY 89 run (conveyor) hours. This is a very loaded, LOW Viet Viet Opera 5 (4) Head 53″ Calibrating Sander

VIET OPERA 7-5.3 HRKXF 1,350 mm (53.15") 5-Head Knife Planer/Calibrating Sander, with 3,634 Powered-On & 675 Run Hrs.Specifications: -- Thickness cap. 200 mm (7.87";).Equipped with: -- 1st Head: “HPG"; Planer Unit, with 180 mm (7.09";) Dia. Cutterhead with (520) Knives & 30 kW (40 HP) Motor, 26-Section Front pressure shoe, & Single back pressure shoe with chromium anti-wear lip. -- 2nd Head: “2620"; Working Unit, with 320 mm (12.60";) Dia. 90 Shore Rubber-covered contact roll with 22 kW (30 HP) Motor, Cam shaft system belt cleaning blower, & Single front pressure shoe with chromium anti-wear lip. -- 3rd Head: “KOMBI 2620"; Combination Working Unit, with 190 mm (7.48";) Dia. 60 Shore Rubber-covered contact roll, Platen with “IPA"; Electronic segmented pad with (42) Segments, 32 mm (1.26";) Pitch, Low pressure action, & Contact insert with Steel & felt grooves & Removable graphite cloth, 18.5 kW (25 HP) Motor with Electronic inverter, & Cam shaft system belt cleaning blower. -- 4th Head: “X-SPIN PLUS"; Unit, with (15) Discs, with Steel inserts & Slots for 180 grit abrasive inserts, & 11 kW (15 HP) Motor with Electronic inverter. -- 4th Head: “2620"; Superfinishing Unit, with 2,160 x 1,420 mm (85.04"; x 55.91";) Chevron belt with Removable graphite cloth, & Platen with “IPA"; Electronic segmented pad with (42) Segments, 32 mm (1.26";) Pitch, Low pressure action, & Contact insert with Steel & felt grooves & Removable graphite cloth, 15 kW (20 HP) Motor with Electronic inverter, & Cam shaft system belt cleaning blower. -- All heads with Disc brakes. -- Adjustable 55 Shore spiral grooved rubber-coated pressure rollers. -- 200 mm (7.87";) Dia. “SCOTCH-BRITE"; Brush roll, with 1.1 kW (1-1/2 HP) Motor. -- Rotary Panel cleaner, with Air saving system. -- 50 Shore Rubber ground laminar surface vacuum feed belt, with 900 mm (35.43";) Height, 7.5 kW (10 HP) Motor with Electronic inverter, & Pneumatic belt tracking. -- 3-Roll Front & rear table extensions, Each with (1) Driven & (2) Idler Rollers. -- All motors with IP54 & Thermal relay protections. -- Self-lubrication system for pneumatic components. -- Front safety bar. -- Carbon steel electro-welded profile frame. -- IPC 15"; Touchscreen control (“SOPHIA"; IoT Connection-ready), with 100-Working program memory, Motor load meters, & Electronic digital readout with Automatic thickness positioning.Complete with: -- Translucent “LEXAN"; Side doors. -- 150 mm (5.91";) Wireless Panel Thickness Caliper.

VIET Challenge S2-3232620-SW53 Wide Belt Sander, 3-Head with (3) Contact Rollers3-Head, 1,350 mm (53") max. working width. Solid wood and thick veneer sander. Head configuration:1st Head: Rubber covered contact roll 320 mm (12-1/2") diameter. Shore hardness 80, 18.5 KW motor, abrasive belt speed 24 m/Sec. (79 FPS).2nd Head: Rubber covered contact roll 200 mm (7.9") diameter. Shore hardness 50. 15KW motor. Abrasive belt speed 20 m/Sec. (66 FPS).3rd Head: Rubber covered contact roll 200 mm (7.9") diameter. Shore hardness 30. 14 m/Sec (46 FPS). (2nd motor 15 KW drives 2nd & 3rd headSpecifications: --All heads equipped with 1380 x 2620 mm (54 " x 103") abrasive belts; roller & pressure shoe hold downs. -- Feed system: Vacuum conveyor system. 3 KW (4 HP) motor variable speed belt drive from 3 - 16 m/Min (11 - 52 FPM). -- Material thickness range 3 - 160 mm (0.1 - 6.3"). -- Pneumatic feed conveyor tension; constant pass-line with height adjustment (for varying material thickness) with digital read-out, driven by 0.75 HP (0.55 KW) motor for the upper section. -- Machine control system: PLC processor control with sequential motor startup and storage for multiple sanding programs.Equipped with & Features: --Panel cleaning followed by turbo-jet air jets at exit side; belt cleaning by air blasts. -- Load meters on all heads. Dust extraction for each head [email protected]" diameter and [email protected]"; disc brakes on all heads; emergency stop for belt breaks. CE Compliant.Note: Comes with 2 extra rollsActual model is VIET S2-3232620-SW53 Wide Belt Sander

VIET Planer Sander Sander model S2 321 HR/KRT ( 2018 ) !st head planer with helical insert cutter knives 30 HP 460 volts 2nd head drum contact roller 3rd head combination drum rollers with finish platen Both sanding heads run by 30 HP motor 460 volts Adjustable rubber coated pressure rollers Opening capacity range 1/8” to 6” Sanding belt size 44” x 103” Feed speed 19 to 52 FPM Electronic digital readout with auto thickness positioning Disc brakes on each machining station Front and rear emergency push buttons Electro pneumatic sanding belt tracking This machine has low hours as owner only ran half days first year and less after next years

VITAP - RC 92, ...Semi-Automatic Top & Bottom Edge Trimmer: New, Never Used!Specifications -- For straight & curved edge banded panels. -- Max. edge thickness: 3 mm (0.12"). -- Panel thickness: 10 - 60 mm (0.39" - 2.36"). -- Table size: 27" x 31".Equipped with: -- (2) 0.55 kW (0.7 HP) - 12,000 RPM Spindle motors. -- Large dia. guide bearings to ensure precise trimming of edges.NOTE: Sold "As Is" without Warranty!

VITAP ALFA - 27: Construction/Line Borer27-Spindle boring head on 32 mm centers; drills vertically from bottom-up and head rotates to horizontal position for edge boring; head rotation is pneumatic with switch control. -- 2-3/4" Max. drilling depth; 2-1/2 HP - 2,800 RPM motor; pneumatic drill head advance with speed control; head height adjustment with mechanical digital readout; 34" x 20" table size; max. workpiece width 31-1/2". -- Equipped with: Left- & right-side fences for construction boring; (2) pneumatic holddown clamps; 118" line boring fence w/flip stops; pneumatic foot pedal control; magnetic starter; overload protection.

VITAP - ALFA 27: Construction Boring Machine27-Spindle boring head on 32 mm centers; drills vertically from bottom-up and head rotates to horizontal position for edge boring; head rotation is pneumatic with switch control. -- 2-3/4" Max. drilling depth; 2-1/2 HP - 2,800 RPM motor; pneumatic drill head advance with speed control; head height adjustment with mechanical digital readout; 34" x 20" table size; max. workpiece width 31-1/2". -- Equipped with: Left & right-side fences for construction boring; (3) pneumatic holddown clamps; 118" line boring fence with: (4) Flip stops; pneumatic foot pedal control.

For pre-glued PVC, veneer, & melamine laminate coil stock; 0.4 - 1.2 mm edge thickness; up to 35 mm panel thickness cap., automatic coil feed. -- Equipped with: Electronically controlled temperature setting for hot air blower; 3,000 Watts for up to 650° F temperature; (1) Min heat up time. -- Guillotine type front & rear end trim (with fast speed, flying knife); top & bottom flush trims with single motor drive to cutterheads. -- Overhead belt type feeder; 16 FPM feed speed. -- Mounted on machine base with panel support table.

VITAP LINEA 42 Line Boring SystemSpecifications: -- (2) Drill heads of (21) spindles ea., drills from bottom up, ea. support with 2 HP motor and (21) spindle boring block w/panel support mounted on top; -- Drills panels from 100 - 3,000 mm in length, and 100 - 950 mm in width. Complete with: -- Digital readouts for boring blocks, 2,000 mm bar scale fence with (5) adjustable flip stops. -- (2) Moveable overhead pneumatic holddown cylinders, foot pedal for clamping & boring cycle.

Vitap Forma Boring Machine 21 Vertical Spindles 21 Horizontal Spindles Approx $1000 worth of carbide bits DUAL LINE machine and there are (2) vertical lines of 21 spindles each for a total of 42 ...... PLUS an additional single line of 21 horizontal spindles!

Vitek Stroke sander Approx 8 foot capacity

VALPATO LBK-150-ST 1 Feed Through Profile SanderTECHNICAL FEATURES: An added small needle type drum sander can be fitted with drum sanding aggregates of 25, ­30, ­35,­40, ­45 ­50 mm diameters which can be used for tighter curves and smaller radius sanding requirements. Storage compartments (2 in total) are located on each machine extremities, these are easily accessible and can be used for sanding belts and various tooling storage. Sanding belt motor power: 3 Kw Abrasive head motor power: 1.5 Kw Oscillation motor power: 0.38 Kw Feed motor power: 0.75 Kw Motor power for electrical adjustment of sanding group: 0.19 Kw Machine voltage: 480/3/60 Full Load Amps @ 480V: 15A Compressed air: Not required Dust collection requirement one (1) only 6" (150mm) port: 950 CFM Sanding belt speed: 14 Mt/sec Variable speed of the belt: from 5 to 25 m/min Sanding belt dimensions: 150 x 2640 mm Height of working table: 930 mm Dimensions of front working table: 1980 x 250 mm Machine dimensions: 2500 x 900 x 1600 mm Net weight: 1000 KMAIN FEATURES: User friendly PLC touch screen control panel is accessible from 360° by the operator, the control panel is centrally located on the infeed end of the machine. Factory installed variable feed drive (VFD), enables machine to run from 5 M/Min to 25M/min (+/­ 80 ft/Min). The entire sanding plenum rise and fall is motorized, it can be adjusted vertically in height to utilise the full height/width of the sanding belt. An oiling unit ensure long life of sanding plenum rise and fall master cylinder.

VOORWOOD M 15A CNC Round End Tenoner & Mortiser for 45° Door --The "M15A" Miter Machine is designed to rapidly make mortise and tenon cuts at 0°, 45° Only, . Parts can be up to 1.5"; thick and up to 4"; wide, and of ANY length. --A primary application for this machine is for miter cabinet door frames. Parts can be quickly transferred from left to right. They are mortised on the left side of the machine and tenoned on the right. The machine can also mill the slots. --Specifications & Equipped with: -- The mortise station has (3) servo-controlled axes (X, Y, and Z) that are coordinated by the machine controller to achieve complex CNC motion. It is equipped with a collet-style router spindle for cutting. The tenon station uses the same X- and Y-servo-controlled axes as the mortise station and is configured for pneumatically actuated in-and-out movement along the Z-axis. The tenon station is equipped with a direct drive shaper spindle for cutting. -- -- Pneumatic clamping assemblies with non-marring urethane pads are mounted to the hold-down assembly to secure the parts during cutting and these can be adjusted to various locations over the cutting surface. -- -- M15 Miter Machine operator interface consists of a colored touch screen. For simplicity, the entire calibration, setup, and monitoring of the machine are accomplished using only four touchscreen displays. The program designs the depth and location of both the mortise and the tenon. When the design is complete, it is saved in a recipe format. Once this recipe is opened, the operation is as simple and boils down to feeding the substrate into the machine. -- -- The full-color touchscreen panel is located on the front of the machine to provide easy access for setting up or operating the machine. Clamping and shaping operations are controlled by operating lighted pushbutton switches.