Woodworking Equipment For Sale

EXTREMA EXCESS XS-1E37 SINGLE HEAD WIDE BELT SANDER37" Width capacity, 0" to 6" conveyor bed opening. Mono-block construction for solid, vibration free operation and increased durability. -- Equipped with: Combination sanding head with rubber covered contact roll & graphite covered platen. -- Over thickness material feeding safety device. -- Digital material thickness controller setting with LED readout accurate to a thousandths of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic abrasive belt tracking. -- GOODYEAR Endless conveyor belt with automatic belt tracking. -- 20 HP Main motor. -- REGAL Variable feed speed drive unit; 2 HP motor. -- 1/2 HP Power elevation motor. -- Large cabinet style doors for easy service access. -- Pneumatic abrasive belt tensioning. -- Double infeed & outfeed covered holddown rollers. -- Infeed conveyor extension with safety stop bar, emergency stop button and motor load meter. -- Operations manual & free box of 3M Sanding Belts. -- Optional 460 Volt / 3 Phase.

EXTREMA XS-1E43 Single Head Wide Belt Sander42" Working width, up to 5" max. opening with electronic digital microprocessor thickness control.Equipped with: -- Rubber-covered contact drum and 2-1/2" wide finishing platen, 25 HP main motor; -- 43" x 60" Abrasive belt, TRU-TRAK solid-state electronic belt sensing with pneumatic tracking. -- GOODYEAR Endless conveyor belt with pneumatic tracking, 2 HP variable speed feed motor from 15 - 48 FPM. -- 0.5 HP Motor to raise & lower table via (4) jack screws, an over-thickness bar at the infeed of machine, and AUTO-SET thickness device. Complete with & Features: -- Double infeed & outfeed rubber covered holddown rolls. -- Air operated disc brakes on main motor, front & rear emergency stop buttons, and motor load meter. -- SQUARE D Electrical controls; magnetic Starter with overload protection, and electrical interlock at sanding belt access doors.NOTE: Also available wired for ...460V operation.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

EXTREMA ET-120.3 Shaper w/Fixed Spindle; "Extremely" Well-built and with solid features. -- 5 HP motor. -- Interchangeable spindles of 1-1/4" & 3/4" and (1) router collet adapter. -- Dual belts and (2) spindle speeds of 7,500 & 10,000 RPM. -- Heavy cast iron table with a 6" max. table ring. -- Spindle lock, micro-adjustable back fence and reversing switch. -- Miter gauge, 1/2" router collet adapter and cutterhead guard.

"Extremely" Well-built and with solid features. -- Solid spindle of 1-1/4" with 5-13/16" under nut. -- Dual belts and (3) spindle speeds of 5,500 - 7,500 & 10,000 RPM. -- Heavy cast iron table with a 12-3/8" max. table ring. -- Spindle lock, micro-adjustable back fence and reversing switch. -- Large 7.5 HP motor. -- Miter gauge, cutterhead guard assembly, operators manual, and tool kit.

EXTREMA ET-100 Fixed Spindle Shaper; "Extremely" well-built and with solid features. -- Single phase with 3 HP or 3-phase with 5 HP motor. -- Interchangeable spindles of 1-1/4" and 3/4". -- (2) Spindle speeds of 7,500 & 10,000 RPM. -- Heavy cast iron table with a 6" max. table ring. -- Spindle lock, micro-adjustable back fence and reversing switch. -- Miter gauge, 1/2" router collet adapter and cutterhead guard.

EXTREMA ET-120 Spindle Shaper;"Extremely" Well-built and with solid features. -- 5 HP Single-phase motor. -- Interchangeable spindles of 1-1/4" & 3/4" and (1) router collet adapter. -- Dual drive belts and (2) spindle speeds of 7,500 & 10,000 RPM. -- Heavy cast iron table with a 6" max. table ring. -- Spindle lock, micro-adjustable back fence and reversing switch. -- Complete with: Miter gauge, 1/2" router collet adapter and cutterhead guard.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Fanuc Robot with Controller Box and Teach Pendant Model: S-420iF Type: A05B-1313-B501 Part #: R98Y03430 Date: 1998.11

45 KVA 480 volt to 208Y/120

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.

FELDER G-330 EDGEBANDER0.4 - 3 mm Edge thickness cap. and 40 mm panel thickness; 3" min. width and 4-3/4" min. panel length.Equipped with: -- Quick Melt Teflon coated glue pot for granular hot-melt adhesive. -- Heavy Duty guillotine for up to 3 mm thick PVC. -- Integrated Operator PLC controls and an LCD display. -- "Anti-slip" rubberized surface chain pads.Workstations: -- Single motor, Double Blade End Trim with HF motor - 12,000 RPM. -- Top & Bottom Flush/Bevel Trim, bevels 0° - 15° (0.5 HP motor - 12,000 RPM each). -- Open space at out feed . -- Single feed speed of 26 FPM.Complete with: -- Sound & Safety enclosure over trim stations and outrigger panel support, and used tooling.NOTE: Seller states that the equipment has less than 500 hours of use!

Felder Format 4 Edgebander Model: Tempora 6012

Felder Format 4 Edgebander Model: Tempora 6012 Return conveyor is no longer available.

FELDER FORMAT 4 TEMPORA F400 45.03 EDGEBANDER (W/PRE-MILL) + EVA/PUR GLUING TECHNOLOGY: -- Specifications:Working Capacity:Min. workpiece width: 70 mm; min. workpiece length: 140 mm; min. workpiece height: 8 mm; max. workpiece height: 45 mm; edge thickness in coils (min./max.) 0.4 - 3 mm.Features & Equipped with: "M-motion" SmartTouch Control with: 10.4" Touchscreen display with integrated maintenance software and network connection. -- Solid steel machine chassis. -- Pullout workpiece support to assist in the processing of larger work-pieces. -- Motor-driven adjustment of the top pressure beam with (2) offset lines of rollers for equal pressure distribution on the workpiece. -- Chain feeder with a speed of 9 MPM (30 FPM) and rubber grip pads for maximum grip on the workpiece. -- 770 mm Diameter workpiece support roller; running on ball bearings. -- Feeding guide with rollers for processing fragile material.Working Units: Pre-milling unit with: (2) 1.1 kW Independent motors running at 12,000 RPM and diamond-tipped cutters; motor-driven positioning of the depth of cut between 0 – 2 mm; (2) diamond-tipped cutters included (Dia. = 80 mm, H = 49 mm, Z = 2+2). -- Edge feed for coiled material: 0.4 – 3 mm Thick coil stock, with edge presence recognition via an infrared sensor. -- Guillotine trimming unit for: Precutting of PVC/ABS edge band material 0.4 – 3.0 mm thick. Teflon coated gluepot with: (10) Minute heat up time; 1.5 kG capacity. - Glue is applied using a fine adjustable glue roller and quick-change System, as well as monitoring of the heating cartridge; pneumatically feed controlled glue unit capable of processing EVA and PUR hot-melt glue. Motor-driven positioning of the pressure unit with: (1) Large motor-driven roller and (1) conical roller operating pneumatically. -- End trimming unit with: (1) Motor, 0.35 kW and 12,000 RPM. -- Multi-functional trimming unit for: Radius & flush trimming and bevel trimming of thin edges with (2) independent motors, each with 0.75 kW and 12,000 RPM; manual positioning of the edge thickness adjustment with pneumatic disengage function via the Control Panel. -- Finishing Units with: 0° - 10° Manual adjustment. -- Complete with: Cleaning & Release Sprayers; T & B Buffing units. -- Actual Model is: FELDER FORMAT 4 TEMPORA F400 45.03.

Felder Format 4 Tempora 60.16L Edgebander

Felder Profit H10 CNC Router (2) Vacuum Pumps 7.5 HP Tool Changer Outfeed Conveyor

Felder Profit H10 CNC Router (2) Vacuum Pumps 7.5 HP Tool Changer Outfeed Conveyor

Single Phase 9ft Sliding Table K 500 S 230V / 1Ph / 60 Hz

Model G660 230V / 3Ph / 60 Hz With Premilling Automatic edge feeding