Woodworking Equipment For Sale

BRANDT - KDN 330, ...Compact EdgebanderSpecifications: -- Edgebanding thickness: 0.4 - 3 mm (0.02" - 0.12"); max. edge banding height: 45 mm (1.77"). -- Panel thickness: 8 - 50 mm (0.31" - 1.97"); min. panel width: 60 mm (2.36"); min. panel length: 140 mm (5.51"). -- Feed chain height: 35"; feed speed: 11 MPM (36 FPM); outboard support adjustment: 13".Equipped with: -- 800 mm (31-1/2") Dia. Coil table. -- Hot-melt granulate glue system with (10 - 12) Min heat-up time; reversible rotation glue applicator roller; automatic reduction glue temperature adjustment (when idle drops to 150°, 2-1/2 Min. to reactivate). -- 3 mm (0.12") PVC Pneumatic guillotine with double-acting pneumatic cylinder; automatic feed magazine; roll & fixed length. -- Pressure section with: (1) Large electronically controlled & feed speed synchronized driven and (1) small idler roll. -- 0.55 kW (3/4 HP) Feed belt motor; touchpad control with LCD Display; sound enclosure.Workstations: -- Front & Rear End Trim Unit with: (2) 0.18 kW (1/4 HP) - 12,000 RPM - 200 Hz Motors with electric brake; 0° - 15° Chamfer. -- Top & Bottom Flush/Bevel Trim Unit with: (2) 0.27 kW (1/3 HP) - 12,000 RPM - 200 Hz Motors with electric brake; combination insert knifes for flush & bevel trimming; vertical & horizontal tracing; 0° - 15° chamfer. -- Top & Bottom Buffing Unit with: (2) 0.09 kW (0.12 HP) - 2,710 RPM Motors. -- Manual height adjustment of top pressure beam for all workstations with Digital height gauge.Complete with: -- Documentation.

BRANDT - F-13, ...Top & Bottom TrimmerFor simultaneous top & bottom flush/radius trimming of the oversized edgeband on straight & shaped workpieces with inside-and-outside radii.Specifications: -- Top & Bottom edge trim PVC, HPL, and veneer edgings; up to 3 mm max. thickness. -- Manually operated; 1/2" - 2-1/4" panel thickness; 1-3/8" min. inside radius. -- Features: Independent top & bottom trim heads (0.5 HP - 11,800 RPM motor each). -- Built-in air jet blowoff device; 31" x 48" table size; dual foot pedal control.NOTE: Intermittent fault in the Control Panel, which will require replacement.

BRANDT - KDN-530C, ...Single-Sided Edgebander with Corner RoundingNOTE: in 2010 Seller purchased NEW in crate, and all workstations are adjusted by Servo motors.Specifications: -- Edge thickness cap.: 0.4 - 6 mm (0.02" - 0.24"). -- Panel thickness cap.: 5/16" - 1-5/8"; min. panel length: 160 mm (6.30"); min. panel width: 65 mm (2.56"). -- Feed speed: 36 FPM.Equipped with: -- Line control (No limit switches) for workstation function. -- Automatic height adjustment with: Top pressure beam for all workstations & digital height indicator for 8 mm - 40 mm (0.31" - 1.57") panel heights. -- "POWER CONTROL PC-20+" Control with: PLC (Programmable Logic Control); VGA Screen; Touchpad; internal modem for remote diagnostic link; signal infeed light to insure proper spacing between panels. -- Quick heat-up glue system; heat-up time approx. 12 Min with: Glue tank for maintenance & glue color change; glue temperature indicator for both glue pot & glue roller with LED thermostat; automatic temperature setback if machine is idle for (15) Min; glue applicator roller is reversible & retractable from fence line. -- Automatic magazine for strip & coil; 800 mm dia. (31-1/2") coil table accommodates large coils of 3 mm (0.12") PVC stock; 3 mm (0.12") PVC Guillotine. -- (1) Drive plus (1) split secondary roller, pneumatically controlled pressure sections. -- 3 HP Feed motor.Workstations: -- End trim unit, with 1/4 HP - 12,000 RPM High-frequency motors with Electronic brakes, Chamfers 0° - 15°. -- Top & bottom flush/radius trim unit, with 1/2 HP - 12,000 RPM High-frequency motors with Electronic brakes, Bevels 0° - 15°, with Insert knives for 3 mm (0.12") PVC radius & "Quickset" with Digital counters. -- Single-motor corner rounding unit, For "On-the-fly" corner rounding, with 1/2 HP - 12,000 RPM Motor. -- Top & bottom scraping unit, For 3 mm (0.12") Radius, with Pneumatically-controlled indexing system & Dust collection. -- Top & bottom buffing unit, with 1/4 HP - 2,800 RPM Motors.Complete with: -- Manual.NOTE: Seller estimates he ran (70,000) parts on machine.

BRANDT - KDN 520, ...Edgebander0.4 - 8 mm (5/16") Edge cap.; panel thickness 15/32" - 2-5/32"; min. panel length 160 mm (6-3/8"); 65 mm (2-1/2") min. width; line control (NO limit switches) for workstation function. Automatic height adjustment with: Top pressure beam for all workstations; equipped with digital height indicator.Specifications: -- PC-16 Program Control; 7-1/2" VGA screen 8 MB IDE flash disk; 8 MB RAM; internal modem for remote diagnostic link; signal infeed light to insure proper spacing between panels.Equipped with: -- Quick heat-up glue system (approx. 12 Min); glue tank for maintenance & glue color change. - Glue temperature indicator for both the glue pot and glue roller with: LED Thermostat and automatic temperature reduction if the machine is idle for (15) Min or more. -- Glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm dia. to accommodate large coils of 3 mm PVC) stock; 3 mm PVC guillotine; (1) drive plus (1) split secondary roller "pneumatically controlled" pressure sections.Workstations: -- Double-end trim (0.33 HP - 12,000 RPM motor); chamfers 0° - 15° via programmable controller. -- Top & bottom flush/radius trim; bevels 0° - 15° (0.5 HP - 12,000 RPM motors). -- Top & bottom scraping for 3 mm radius; pneumatically controlled indexing system. -- Top & bottom buffing (0.25 HP - 2,800 motors).Features: -- End trim & flush trim stations: HF Motors w/electronic brakes; feed chain track speed 36 FPM; 2 HP feed drive. --Complete with: Operator Control Panel with: PLC (Programmable Logic Control) keypad & LED readouts; used tooling. -- Machine in use and available time to be confirmed.

BRANDT - KD 56, ...EdgebanderSpecifications: -- 0.4 - 3 mm (1/8") Edge thickness cap.; automatic coil & strip feed magazine; guillotine for 3 mm PVC banding; fast startup (10 Min heat up) glue system. Workstations: -- Vertical travel double-motor front & rear end trim; 0.25 HP - 12,000 RPM motors. -- Top & bottom flush/bevel trimmers; bevel 0° to 15°; 0.35 HP - 12,000 RPM motors. -- Top & bottom PVC scraping unit for up to 3 mm radius. -- Top & bottom buffing unit; 0.15 HP - 2,750 RPM ea. motor; feed speed: 30 FPM.

BRANDT KDF 660 Edgebander w/Premilling & Corner RoundingSpecifications -- 0.4 - 15 mm (5/8") Edge cap.; panel thickness 5/16" - 2-3/8"; min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; -- Line Control (NO limit switches) for workstation function. -- Pressure beam height adjustment for all workstations via digital height indicator. -- PC-20 Program Control with: 12" Industrial PC screen; 256 MB RAM; 1 gB Flash card with USB Port & remote diagnostic link. -- Signal infeed light to insure proper spacing between panels.Equipped with: -- 2-Motor Premill unit; (2) 3 HP motors (12,000 RPM) with straight and chamfer capability; program controlled indexing from straight to bevel. -- Quick heat up glue system (approx. 10 minutes); hopper feeder & glue tank for maintenance & quick glue color change.Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for (15) minutes or more. -- The glue applicator roller is reversible and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table; 800 mm dia. to accommodate large coils of 3 mm PVC stock); 3 mm PVC guillotine; (1) drive plus (3) secondary rollers "pneumatically controlled" pressure sections. Workstations: -- Double-end trim with: (2) 0.5 HP - 12,000 RPM motors; chamfers 0°- 15° via programmable Controller. -- Top & Bbottom flush/radius trim; bevels 0° - 15° (0.75 HP - 12,000 RPM motor); insert knives for 3 mm PVC radius. -- Corner Rounding Unit. -- Top & Bottom scraping for 3 mm PVC radius; pneumatically controlled indexing system. -- Top & Bottom oscillating buffing (0.25 HP - 2,800 motors). -- Variable feed speed 36 - 65 FPM (3 HP feed motor).

BRANDT AMBITION 1650 FC High Flex EDGEBANDER (W/PRE-MILLING & CORNER ROUNDING): -- Specifications: Edge thickness 0.4 - 12 mm (0.02" - 0.5"), incl. 3 mm (0.12") PVC banding. -- Workpiece thickness 8 - 60 mm (0.314" - 2.375"). -- Min. workpiece width 70 mm (2.76"), Min. workpiece length 160 mm (6.37"). -- Working height 950 mm (37.8"). -- Equipped with:3 HP (2.2 kW) Feed motor for variable feed speeds from 26 - 59 FPM (8 - 18 MPM) applying solid or using corner rounding units. -- Infeed panel support with roller guide extends out to 800 mm (31.4"). Motorized top pressure beam adjustment with 0.16 HP (0.12 kW) Motor. -- 80 mm (3.15") W Heavy Duty feed chain, with rubber pads, automatic chain track lubrication. -- Top pressure section with double-wide compound V-belt to prevent panel movement. -- All cutting & trimming workstations are HF (High Frequency Motors); line control (no limit switches) for workstation functions. -- Top & bottom spraying device located in front of pre-milling station for easy residual glue cleaning. -- Manual adjustment in case of modified panel overhang. -- Automatic edge infeed. -- Reinforced guillotine for coiled edgebanding material; 0.3 - 3 mm (0.01 - 0.12") thickness & 8 - 45 mm (0.314" - 1.78") Height.Pre-milling Station: -- (2) 3 HP (2.2 kW) - 12,000 RPM Vertical milling/jointing heads, Electro-pneumatic jump control on 1st motor, electronic frequency inverter for control of motor speed & braking, SIKO digital units for vertical & horizontal adjustments.Glue Preheat Unit: -- 2.5 kW, 3 kG (6.61 Lbs) cap.; glue viscosities 25,000 - 80,000 mPa, temperature range 120° - 245° C (248° - 473° F); max. melting capacity 6 KG/Hr.EVA Hot Melt Glue Application System: -- Quick-change glue tank for easy maintenance & glue color change, melting capacity approx. 6 - 10 KG/Hr; glue reactivating infrared heating unit positioned between glue roller & pressure zone to improve edge quality.Pressure Zone: -- Program controlled positioning of the pressure zone; (1) large driven & (3) secondary pneumatically controlled idle rollers.Workstations: -- Front & Rear End Trimming Unit with: Gap optimization, (2) 0.5 HP (0.35 kW) - 12,000 RPM motors, electro-pneumatic reset for straight or chamfer trimming. -- Top & Bottom Multistage Trimming Unit: (2) 0.73 HP (0.55 kW) - 12,000 RPM Motors with vertical & horizontal tracing; 2-position programmed controlled indexing. Position #1 with a slight projection of 0.2 mm & Position #2 with flush trimming without projecting edge; Servo motor, controlled positioning of the work units and side copy for multiple edge thickness. -- Multifunction Profile Trimming Unit (Corner Rounding) with: Magnetic drive technology, (2) 0.54 HP (0.4 kW) - 12,000 RPM motors, 18 MPM (59 FPM) max. feed speed; 3 mm (0.12") max. edge thickness, 12 - 60 mm (0.50 - 2.375") workpiece thickness, quick-change motor system for different radius profiles, pneumatic (2) position indexing for different edge thicknesses

BRANDT "KDF-980 2C" EDGEBANDER WORTH PRE-MILLING & CORNER ROUNDING 0.4 - 20 mm (3/4") Edge thickness capability; Min. workpiece width 65 mm (2-1/2") and min. panel length 160 mm (6-1/3"), panel thickness 8 - 55 mm (5/16" - 2-3/16") .Working height 900 mm (35"); 80 mm wide Heavy Duty feed chain w/rubber pads, automatic chain track lubrication, 3 HP (2.2 kW) feed drive for variable feed speed 11 - 20 MPM (36 - 65 FPM) (max. using solid wood 52 FPM); motorized upper pressure beam.7.4" Matrix color LCD Screen "PC-16" Integrated Microprocessor Line control for programming the various working functions; features internal modem for remote diagnostic link.Pre-Milling Station, (2) 3 HP (2.2 KW) - 12,000 RPM Vertical milling/jointing heads, electro-pneumatic jump control, heads counter-rotate, SIKO digital units for vertical & horizontal adjustments.Quickmelt gluing system with large granulate hopper with automatic glue feed system (approx. 12 Min heatup time); pre-melting unit between hopper and reversible & retractable glue roller; infrared radiant glue heat zone between glue roller and pressure section for optimum gluing strength.Automatic magazine for strip and coil feeding with automatic coil feeding system; 2-coil table for one roll thick PVC and one for thin edgings; wide magazine with automatic feeding of wood strips; program controlled.Motorized pressure section with (1) large driven pressure roll and (4) secondary idle rollers with pneumatically controlled side pressure; solid wood infeed device.Workstations Edgebanding:End Trimming (1 HP / 0.75 kW) - 12,000 RPM motor, program controlled pneumatic indexing of straight or chamfer trimming, chamfers up to 15°.Top & bottom rough (flush) trimming (2 HP / 1.5 kW) - 12,000 RPM motor ea. w/vertical tracing.Top & bottom fine trim (0.75 HP /0.55 Kw) - 12,000 RPM motor ea., bevel 0° - 25° tilt angle, w/vertical & horizontal tracing, servo driven in/out adjustment controlled from control panel.Corner rounding unit with (2) motors ( 0.50 HP / 0.4 Kw) - 12,000 RPM motors ea, 16 MPM (52 FPM) operating feed speed, pneumatic (in/out position) control from control panel (all trim station motors are 200 Cy HF and equipped w/electronic brakes). Top & bottom scraper for finishing PVC edging.Hot air blower (post heating) for reactivating scraped, thick PVC edgebanding.Top & bottom "oscillating & jump" buffing unit (0.3 HP - 2,800 RPM motors), tilt vertically & horizontally.Complete with: All working units & fence adjustment throughout machine with SIKO digital readouts, operator controls on overhead swivel arm.Includes: Sound enclosures with 1" thick padding over all milling stations in edgebander section, and digital counter at infeed to measure footage of product edgebanded.A 20 year old machine with 3573 hours on it !only ran for 15 hours per month all parts and tech support available from Homag Brandt

BRANDT KDN 650 C Edgebander; 6-Station Edgebander with 0.4 - 8 mm (5/16") Edge capacity. Specifications: -- Panel thickness 5/16" - 1-9/16", min. panel length 160 mm (6-3/8") and 65 mm (2-1/2") min. width; -- Line control (NO limit switches) for workstation function. -- Automatic height adjustment with top pressure beam for all work station, equipped with digital height indicator. -- PC-16 Program Control with 7-1/2" VGA screen 8 MB IDE flash disk, 8 MB RAM, Internal Modem for remote diagnostic link; -- Signal infeed light to insure proper spacing between panels. Equipped with: -- Quick heat-up glue system (10 to 12 minutes). -- Automatic magazine for strip & coil stock (large coil table 800 mm diam. to accommodate large coils of 3 mm PVC), 3 mm PVC guillotine; -- (1) Drive plus (3) idle roll "pneumatically controlled" pressure sections. Workstations: -- End trim (1/3 HP - 12,000 RPM motors) chamfers 0° - 15°; -- Top & bottom flush trim, bevels 0° - 15°, (2) 1/2 HP - 12,000 RPM motors) with insert knives. -- 2-Motor (4-corners) contour trim for profile corner rounding (2) 1/2 HP - 12,000 RPM motors), with insert knives for 3 mm PVC radius. -- Top & bottom scraping for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. -- Last Station: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Feed chain track speed 42 FPM, 2 HP feed drive. Complete with: Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts, and used tooling.

Brandt KDF 440 Highflex 1440 Edgebander

BRANDT AMBITION 1440 (KDF-440 C) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Adjustable Infeed Fence: Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for leading & trailing edges vertical corner rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Glue Scraping Unit: Flush on panel surface with floating insert knives. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 (KDF 440 C).

BRANDT AMBITION 1440 FC (KDF-440 FC) EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications: Edge & workpiece capacity: 0.4 - 8 mm (0.016" - 0.31") Edgebanding thickness, 8 - 60 mm (0.31" - 2.36") panel thickness, 160 mm (6.30") min. panel length, 70 mm (2.76") min. panel width.Equipped with: -- Heated Adjustable Infeed Fence: Radiant Heated with Manual adjustment. -- Joint Trimming/Pre-milling Station: (2) 2.2 kW (3 HP) 12,000 RPM Motors, left-hand & right-hand rotation with Pneumatic jump control for chip-free & clean panel edges. -- Roller Separating Device: 3 mm x 45 mm (0.12" x 1.77") or 1 mm x 55 mm (0.04" x 2.17") Max. roll cutting; 0.4 - 8 mm (0.016" - 0.31") strip thickness; 3 mm (0.12") PVC max. coil thickness. -- Hot Melt Glue Application Unit: 6 - 10 kG/Hr (13 - 22 Lbs/Hr) Melting capacity (depending on glue type). -- Pressure Zone: (1) Driven & (2) idle rollers; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speeds: 8 - 14 MPM (27 - 45 FPM); 11 MPM (36 FPM) when contour trimming. -- BRANDT "POWERTOUCH" Control with: 21" HD LCD Touch Screen Monitor.Workstations: -- Front & Rear End Trimming Unit: (2) 0.18 kW (1/4 HP) 12,000 RPM Motors with 0° - 15° automatic chamfer, pneumatic adjustment & activation/deactivation of edging material overhang using "POWERTOUCH" control. -- Top & Bottom Flush/Chamfer/Radius Trimming Unit: (2) 0.55 kW (3/4 HP) 12,000 RPM Motors, 0° - 25° Automatic tilt with Horizontal & Vertical Tracing wheels, Brushless multi-axis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover with (3) Positioning options: Profile 1, Profile 2 & Flush Trimming. -- Multifunctional Trimming Unit: (2) 0.4 kW (1/2 HP) - 12,000 RPM Motors for Top & Bottom, Leading & Trailing edges & Corner Rounding of panels, Servo motors for positioning of work unit & horizontal copy wheels. Either radius or chamfer cutters can be mounted, 3 mm (0.12") max. edge thickness. -- Top & Bottom Multi-Profile (PVC) Scraping Unit: (2) Profiles: 1 mm (0.04") & 2 mm (0.08") or 3 mm (0.12") instead of 2 mm (0.08"); Servo control positioning of vertical & horizontal copy wheels; PVC scrape collection box, pneumatic adjustment using "POWERTOUCH" control, pneumatic disengagement. -- Top & Bottom Buffing Unit: (2) 0.09 kW (0.12 HP) - 2,750 RPM Motors.Complete with: -- Rubber padded feed chain w/top idle hold-down rollers; 1.5 kW (2 HP) feed motor; 32" diameter coil table; padded sound enclosure. -- Actual Model is BRANDT AMBITION 1440 FC (KDF 440 FC).

Pre-milling Unit End Trim Profile/Flush trimming Unit Corner Rounding Unit Profile scraping Buffing Max feed speed: 10 m/min Maximum panel thickness: 50 mm

0.4 -3 mm (1/8") Edge cap., panel thickness from 8 -40 mm (5/16" -1-9/16"), min. panel length 120 mm (4- 3/4") and 70 mm (2-3/4") min. width. Feed Speed: Feed chain track speed 8 MPM (26 FPM) w/gear motor feed drive not under power Pre-Mill Station: 2-Motor Pre-mill (1 HP-12,000 RPM @ 200 Hz). Gluing Station:"A3" Gluing Unit for granulate adhesive application system with Quick Change application unit underneath glue reservoir, Automatic reduction of glue temperature upon interruption of work. Automatic magazine for coil (table 800 mm dia. to accommodate large coils of 3 mm material) stock Heavy Duty guillotine, strips stacking with automatic strip separation on feeding. Pressure zone with driven main roller & (2) idle post pressure rollers; Digital readout for manual adjusting pressure zone to edge thickness. Work stations: • End trim of front & rear edge (0.24 HP - 12,000 RPM@ 200 Hz motor ea. with 100 mm dia. saw blade). • Top & bottom Flush/Chamfer/Radius trimming(0.36 HP - 12,000 RPM @ 200 Hz motor ea.), sensing horizontally & vertically, DFC combination cutters for flush, chamfer, & radius trimming; (1) set of tools for 3 mm radius, digital readouts for fast adjustment. • Radius Glue Joint Scraping unit Top & bottom for removal of adhesive residue for perfect finish, sensing from top & bottom; height adjustment with top pressure beam. • Glue Joint Scraping unit Top & bottom for removal of adhesive residue for perfect finish, sensing from top & bottom; height adjustment with top pressure beam, equipped with (2) reversible cutter knives. • Operator & Machine Control: "ECO Plus Control", easy operation with simple menu format; large LCD display and integrated line control via keypad. • Complete With: Top pressure with (2) single rows of staggered rubber rollers Transport chain with 80 mm wide with replaceable rubber pads Work piece support track extends up to 300 mm (11.8"). Individual dust extraction ports and Sound & safety enclosure.

Brandt KDF 440C Edgebander

Brandt Ambition 1110 Edgebander

2007 Brandt KDF 680 Single sided Edgebander with Pre Milling and Corner Rounding

Brandt Optimat KDF 230C Edgebander

Brandt 1100 Edgebander Seller closed shop about 1 year ago and put this in storage. Claims they were using the machine up until they shut down.

Brandt KDN 770 2C Machine has been removed from service. Owner claims it is ready to run! Specs (to be confirmed): Hot Melt granulate quick heat-up glue system, overhead glue tank for easy maintenance & glue color change. Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. (1) Drive plus (3) idle rolls "pneumatically controlled" pressure sections. End Trimming: 0.33 HP - 12,000 RPM Motors, chamfers 0° - 15°. Flush Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index pre-sets, (2) 0.5 HP - 12,000 RPM motors, cutter heads with insert knives. Fine/Radius Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index presets (0.5 HP - 12,000 RPM motors), cutter heads with insert knives for 3 mm PVC radius. 2 motor corner rounding Scraping Unit: Top & bottom for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. Buffing Unit: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Variable feed chain track speed from 8 - 20 MPM (26 - 65 FPM), 2 HP feed drive.