Woodworking Equipment For Sale

Holz-her 1315 Edgebender

Holzher Ergebender

HOLZ-HER AURIGA 1308 XL EDGEBANDER (W/PREMILL & CORNER ROUNDING): + "GLU JET" EVA/PUR GLUING TECHNOLOGY: -- Specifications:Servo controls on the following: Pressure beam height; Top & Bottom trimmer; 3 mm radius scraper; auto-tilt on end trim; programmable corner rounder; pneumatic finish scraper. (1) Centrally located hand wheel for manual raising & lowering of the top pressure beam. Rigid workpiece support extending 380 mm; manual central lubrication of the transport chain.Feed speed: 10 MPM (33 FPM). -- Working Capacity: Edge thickness: Min./max. 0.4 - 3 mm (0.02 - 0.12"); coiled material; optional with flush cutters max. 6 mm (0.24").Panel thickness: 6 - 60 mm (0.236 - 2.362"); workpiece width min. of 65 mm (2.559"); workpiece length min.160 mm (6.299"). -- Premilling Station "1801":(2) x 1.2 kW (1.6 HP) - 12,000 RPM Motors; diamond cutter heads with ProLock quick clamping system. Quick-Lock adjustable infeed fence with digital indicator. -- Edge Magazine "1903":For coil & strip processing; utilizes motion detector to ensure accurate, trouble free positioning of edge material.Exclusive "Tractor-Belt feed System": Edge guide equipped with: Automatic guillotine lockout for safety.3° Approach angle allows easy feeding of solid wood edges. -- Pressure Section "1912-3P":With (1) large driven (synchronized with feed speed) roller and (2) cantered idle rollers, adjustable by hand wheel and scale. -- Glue Jet systemUpper glue line height positioning is set automatically with hold down beam setting.Heat up time to ready stage takes only (2 - 30) minutes!NOTE: Granulate requires an "optional" hopper. - Select our "Select Literature" link on the detail page and scroll to "Page-8" for more details.Workstations: -- End Trimming Unit "1918P": Front & rear 2 x 0.45 KW (0.6 HP) - 9,000 RPM motor each,Uni-point swivel-axis for no re-indexing when changing from flush to bevel end trim (0° - 10° bevel)."PCS" programmable pneumatic change-over from flush to bevel. -- Flush/Bevel/Radius Combination Trimming Unit "1827P": Flush 6 mm, radius 3 mm trimming, servo controlled, 2 servo motors (1) for horizontal copy wheel & (1) for tool spindle position).Programmable top & bottom unit 2 x 0.65 KW (0.88 HP) - 12,000 RPM each motor.Uni-Point design with no second adjustment, pneumatic, programmable tilt action for changing the degree of bevel,Digital counters for vertical copy wheel position and pneumatic air cylinder for in/out pre-positioning of trimming motor. -- Corner Rounding Unit "1832": (1) Motor 0.22 KW (0.30 HP) - 9000 RPM for up to 3 mm edge thickness.Work-piece thickness min./max. 12 - 60 mm (0.473 - 2.362"), Max. feed speed 10 MPM (33 FMP). -- Profile Scraping Unit "1929":Top/Bottom, servo motor controlled/programmable knife position, vertical copy wheel adjustment with quick setting spindle - for PVC edges,Reversible insert carbide knives, equipped with air-jet blowers and chip collector box. -- Glue Scraping Unit "1964":Flat surface, top/bottom,

Holz-her Vertical 1265 Vertical Panel Saw

Holz-her Streamer 1054 Edgebander Top/Bottom Trimmers End Trimmers Scraping Buffing Station No longer under power - Ready to ship! Serviced by Holly-her tech.

Holzher 1265S Vertical Panel Saw

Year: 2008 Excellent Condition HolzHer Triathlon 1488 Edge Bander Ligmatec Return Conveyor Manual Included Description: PreMill Front & Rear Trim Saws Top & Bottom Rough Cutter Top & Bottom Combination Finish Cutter 3mm Corner Rounding Edge Scraping Edge Buffing Variable Speed 8-18 mpm 8-60mm panel thickness Electrical: 230V 3Phase

Holz-her Cut 85 Panel Saw; under power until 8/21 model 6210

Holzma OPT.HpPS81/38 Panel Saw

HOLZMA PROFIMAT HPL 500 38/16 REAR LOAD, AUTOMATIC PANEL SAW: -- Specifications: 149.6" (3,800 mm) Cutting length & pull-back; 6.7" (170 mm) max. main blade projection; 40 HP (29.8 kW) Main & 3 HP (2.2 kW) scoring motor. -- Saw carriage: Infinitely variable speed from 0 - 492 FPM (0 - 150 MPM), constant return of 492 FPM (150 MPM).Carriage is electronically & automatically controlled (cutting height & length) through the CADmatic according to the material/program being processed."Power-Loc" quick change system for fast and easy saw blade change.NC Controlled scoring saw adjustment from the control panel during operation -- Pusher Fence:Rack & pinion digital drives with AC Servos on both sides, forward speed 295 FPM (90 MPM), return speed 295 FPM (90 MPM).(7) Material clamps which open up to 6.7" (170 mm): (3) Standard clamps with two fingers & (4) clamps with one finger.(4) Trimming rakes for thin strips/scrap removal are attached at the clamps. -- Operator Interface:HOLZMA "Power Touch Control" IPC multi-tasking controller with Windows "7 PRO" + "CADmatic 4.0 PRACTIVE" operating system;Intel i5 Dual-core Processor, Intel HD graphics card, 4GB RAM, SATA 2-250GB hard drive, (6) USB ports, (1) serial port, ATI/DVI video port, Standard industrial keyboard connection,21.5" LCD "Touch-Screen" monitor with real-time moving 2D & 3D graphics (displays cutting dimensions & error diagnostic); virtually unlimited cutting dimension memory.(2) Ethernet 10/100 interface connections; downloading from office PC is possible. -- Rear of machine: Profile rails & "Combi-rollers" at 50 mm centers; (2) integrated front & cross-aligning units before cutting to prevent off-set panels within the same book. -- Front of machine: (3) Air flotation tables 85" x 31.5" (2,160 x 800 mm) with (1) central blower unit. -- Rear Lift Table:7-Ton (14,000 LBS), 4-Column electro-hydraulic powered rear lift table running lengthwise with fork cut-outs, 150" x 63" (3,800 x 1,600 mm) capacity. Powered rollers are 4.2" (107 mm) dia x 7.79" (198 mm) spacing, 39 FPM (12 MPM) infeed/outfeed speed; Feeding material from (3) sides is possible with additional roller conveyors.22" (560 mm) Max. bunk height from floor level; 30.7" (780 mm) max. bunk height with a pit or risers; -- Complete With: Holzma's Unique "EcoPlus" System offers energy savings up to 20%; Includes Standby button & IE3 energy efficiency Motors rating.Angular cross-cut fence; Automatic side pressure device integrated into the saw carriage for cross-cutting, the machine cuts left to right to the cross-cut fence.Front & rear forks electronically & automatically controlled through the CADmatic according to the material/program being processed.Min. side aligning dimension 0" (0 mm), max. side aligning dimension 149" (3,800 mm)."Power-Loc" quick blade change system for main/scoring blades. -- Options Include: &#9679 (1) Non-Powered in/out-feed staging conveyor with fork cut-outs as pictured. &#9679 Micro In-feed for thin an

Holzma HPL11 Rear Load Panel Saw Still under power. Ready to be removed the end of January 2024

Homag Drillteq V200 Model Optimat BHX 055

Homag KAL 310 NOT INCLUDING THE RETURN Year of MFG 2006 Control voltage 24 V total connected load 50A recommended fuse 28kW nominal current pprox.. 39A Dust extraction air velocity (min.) 28 m/sec (91.84 ft/sec) air volume 4090 m3/hr (2407 cfm) static pressure 250 mm/ws (9.84”/ws) CompressedAir connection size ¾” pressure required 7 bar (100 psi) consumption / volume 705 sl/min (24.89 cfm) Foundation requirements according to layout drawing # 5-236-01-0360 Electrical equipment installed according to UL regulations. Voltage supplied must not fluctuate in excess of+/- 5% of its stated value. Voltage must be balanced phase-to-phase and phase-to-ground. Note: The stated values are only applicable to the machine as specified. Adding or deleting optional equipment may change service connection requirements. In case ofvariations in technical specifications and capacities between the base machine and working units, the specifications and capacities given for the working units are to be considered correct. Conditions offloor at installation site must adhere to foundation plan. Adjustable lnfeed Fence Homag Unit #0005 • with digital mechanical counter Pre-Milling Unit Homag Unit #3481 HOMAG KAL 525 • with two (2) motors 3 kW, 150 cycle, 9000 rpm • for max. tool diameter of 125 mm (4-15/16") • equipped with trimming column • two (2) horizontal and cross slides with spindle adjustment • electro-pneumatic horizontal jump movement of first motor • two (2) dust extraction hoods • air jet for panel cleaning • with two (2) DIA jointing heads 125 x 35 x 30 mm(4-15/16" x 1-3/8" x 1-1/8"), DKN, z = 2 x 3 • max. workpiece thickness 30 mm (1-1/8") • electronic frequency inverter for control of motor speed and braking Noise Protection Stepped Homag Unit #0424 • for pre-trimming unit • allows for inlay of long strips • centralized dust extraction port Panel Pre-Heater Homag Unit #2325 • quartz lamp for heating substrate edge before glue application • for improved edge quality and optimum bonding QA 34 Quick Melt Gluing Unit Homag Unit #2123 • specially designed by Ho mag - the original innovator of the quick melt syste • lower reservoir unit is designed with only seven (7) wearing parts, which allows for ease of adjustment and reduces maintenance costs • ideally suited for quick heat-up time and color changes • one bolt secures lower unit to drive mechanism • special coupling eliminates alignment of universal drive joint • digitally displayed thermostat for both upper and lower unit, along with heated glue roller allow for excellent control of temperature for optimum bonding results • individual adjustment for front and rear glue gates • upper reservoir for glue granules • glue roller diameter 34 mm (1-11/32") • lower melting unit equipped with automatic control of glue level Glue Roller Drive Homag Unit #2141 • eliminates glue charring on glue roller • lengthens pot life of glue during idle running time o

Homag BMG 311 Venture 316L CNC

HOMAG KAL 210 AMBITION 2260 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Coiled stock min/max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max. thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor;Includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, an air-jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-Heater: the Pre-heater brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multi-Purpose Magazine: 2-Coil magazine expands capability by running coiled material & strips, magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates, lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 LBS/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 KW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & bottom Flush Trimming Unit: Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12: Multi-function 0.4 KW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10: Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11: Top & bottom edge buffing/polishing, pneumatically activated. -- Operator & Machine Control:HOMATIC PC 22 Power Control w/Touch Screen: Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating syst

Homag Double End Tenoner System will be available approximately August 1, 2023 Also available with a direct transfer conveyor and [Gabbiani DET](https://www.carolinamachinerysales.com/listings/4073350-used-2003-gabbiani-sqv-sqi-double-end-tenoner) currently running inline.

Homag BOF 311/37/15/R CNC Router Specs (to be confirmed): Homag "Vantage 12L" CNC Router Aluminum router table 60" x 144" working area Gridded Pneumatic reference stops Vacuum gauges Foot pedal control Drill unit Nine (9) vertical spindles One (1) horizontal spindle (two outlet) in X axis One (1) horizontal spindle (two outlet) in Y axis Router 16 HP HSK (quick-change) CW/CCW rotation Variable RPM Ten (10) position rotary tool changer Sound enclosure Front safety mats Safety fencing with interlocked access door Controller Flat screen monitor Standard keyboard and mouse Remote control pendant Also included: Laser projecting unit Ceiling mount

Homag BST 500

As Taken From Service: Includes return conveyor

Homag Espana CH-03/32/32-PLUS Panel Saw Still under power and available for inspection. 230/480 V