Woodworking Equipment For Sale

TIMESAVER - TB-440-4, ...2-Head Wide Belt Sander40" Width cap.; Drum and Combination Head.Head Configuration:1st Head - 50 HP; 12" rubber covered contact head.2nd Head - 40 HP; combination platen head.Specifications: -- Sander completely rebuilt (15) years ago. -- Rubber covered abrasive rolls were recovered, grooved and balanced, along with ALL pinch rolls recovered at FLETCHER MACHINE CO., Lexington, NC. -- Electric eyes upgraded to BANNER's send and receive type; includes battery backup system for controls (no crashes when machine has power outage). -- Feed speed gear box driven by AC Drive controlled 10 HP motor. -- Rebuild included: Table removed and platens ground flat; all bearings replaced, including pinch rolls and tracking cylinders; tension cylinders plasma sprayed, reground & new factory seal kits. -- Entire machine was disassembled, sand blasted and DUPONT "Zolatone" primed and painted. -- RAINBOW brand feed conveyor belt replaced in 2014. -- Many more upgrades, too many to list: Please contact for additional information. -- Machine is in good condition, running daily, and has had regular recommended service intervals; includes all factory manuals, blueprint drawings, parts list with numbers supplied, and when machine was new. -- Machine used in solid wood wide belt sanding. -- Includes Cloth aluminum Oxide Belts: 7 - 50 grit; 1 - 60 grit; 8 - 80 grit; 2- 120 grit; 8 -1 80 grit..

TIMESAVER 237-3 IC Wide Belt Sander: 3-Head, 36" cap. - Drum, Drum, Finishing Platen. -- 1st Head: Rubber covered contact roll, 11-1/2" dia., 50 HP motor; -- 2nd Head: Finishing platen 2-1/2" 30 HP motor. -- 3rd Head: Finishing platen 2-1/2" wide, 30 HP motor. Specifications: -- 37" x 75" Abrasive belts. -- "POSI-TRAK" electronic sanding belt tracking. -- Motorized part thickness adjustment. -- 0" - 6" Opening, automatic part thickness adjustment. -- Infeed & outfeed spring loaded holddown shoes. -- Variable feed speed from 15 - 45 FPM, 5 HP feed motor.Additional Features: -- Motor load meters. -- Infeed emergency stop bar. -- Controls mounted on belt loading side. , -- Disc brakes on sanding head motors. -- 30" Infeed load area.Actual model: TIMESAVERS "237-3IC"

TIMESAVER - 337-2, ...2-Head Wide Belt Sander36" Width cap., Drum & Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Rubber contact Roll & Platen 30 HOSpecifications: -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP Feed drive; Variable feed speed from 20 - 60 FPM. -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, 0" - 6" opening. -- Infeed safety stop bar. - Also has adjustable shoes before and after each head. Equipped with & Features: -- Controls mounted on belt loading side. -- Sanding head motors with air caliper disc brakes --Motor load meters.

Single Head Top and Bottom Sander

TIMESAVER 337-2 Wide Belt Sander, (2) Heads36" Width cap., Drum, Combination HeadHead Configurations:1st Head: 11-1/2" Dia. spiral grooved rubber contact roll 40 HP motor.2nd Head: Combination Head, Drum with Platen 30 HP motor. Specifications -- 37" x 75" Abrasive belts with pneumatic tracking. -- 2 HP feed drive; Variable feed speed from 20 - 60 FPM.Equipped with & Features -- Infeed & outfeed spring loaded holddown rolls on both heads. -- Motorized thickness adjustment with indicator, -- 0" - 6" opening. -- Infeed safety stop -- Adjustable shoes before and after each head. -- Controls mounted on belt loading side, --Sanding head motors with air caliper disc brakes, and motor load meters.

Timesavers Model 2331-04-334 3-Head Orbital Sander 43" Machine

TIMESAVERS 252-4-IC, ... Wide Belt Sander, 4-Head.4-Head, 51" cap. - Great sander for solid wood and veneer panels equipped with (2) Contact rolls and (2) Air platens. Head Configuration1st Head: Rubber covered contact roll, 9-1/2" dia. 60 - 70 Durometer, 40 HP motor.2nd Head: Rubber covered contact roll, 9-1/2" dia. 50-60 Durometer, 30 HP Motor.3rd and 4th Head: Finishing platens, 2-1/2" wide "Veneer Saver" inflateable platens with adjustable timers for leading and trailing edges, 20 HP motor each head.Specifications: -- 38" Constant pass line height of Vacuum conveyor with suction fan and motor bed assembly for veneer and solid wood sanding. -- Adjustable air floating infeed and outfeed hold down shoes. -- 52" x 103" abrasive belts with "POSI-TRAK" electronic tracking.Equipped with & Features: -- Motorized part thickness adjustment with mechanical digital readout. -- Auto part thickness set-up, 0" - 6" opening. -- Hydraulic feed belt operation of 15 - 45 FPM via 7-1/2 HP hydraulic pack. -- 4-Motor load meters, controls mounted on belt loading side. -- Disc brakes on sanding head motors. -- 30" Infeed load area.

TimeSaver Mdl 325-2 36" Wide Belt Sander S/N 7887

Dust Collection System

Reconditioned Torit 156RF10 baghouse

TORREDA METOR 1600 UNIVERSAL Copy Lathe; -- Specifications: 63" (1,600 mm) Max. between centers, 9-7/8" (250 mm) max. dia. without traveling steady, 3-1/2" (90 mm) max. dia. through steady rest (larger dia. of 6-1/4" (160 mm) cap. OPTIONAL). -- Equipped with: 4 HP Motor with adjustable turning speeds, (1) HYDRO hydraulic tracing head with 3" stroke, hydraulic controlled tailstock. -- (2) Top mounted manual knives for tenon or cutting using form tools (accepts form tools up to 3" wide); 2 HP hydraulic pump motor with adjustable feed speeds. -- Actual model is HIDRO 80/12 mm. -- Includes matching knife grinder and accessories as pictured

TORREDA TORMADEX S.A. PA-1200 Hydraulic Wood Turning Back Knife Lathe:Nicely equipped Spanish lathe with dual hydraulic tracers for making quick work of all your demanding woodturning production runs! ... Great for turning baseball bats!Specifications: -- 47" Max. between centers, 9-7/8" max. dia. without traveling steady. -- 3-1/3" Max. dia. through steady rest (larger dia. of 6.2" cap. OPTIONAL); -- High speed automatic loading, feeder accepts pieces up to 4" square. -- 4 HP Motor with (4) turning speeds, 1,200, 2,800, 3,500, and 4,550 RPM. -- (2) HIDRO "T-75" hydraulic reproducing heads with 3" stroke. -- (2) Top mounted hydraulic knives for tenon or pattern cutting (accepts form tools up to 3" wide). -- 2 HP Hydraulic pump motor with (3) carriage feed speeds. -- Features: Pressure sensitive Hydraulic tailstock with Pressure Regulating Valve needed for small, slender turnings to avoid buckling. Pre-rounding tool in front of travelling steady rest. -- Includes: Safety guard, tooling with several roughing and finishing knives.

TRAVAINI TRO 501-1A-200V "40 HP VACUUM PUMP (LIQUID RING) 11,969 Hours:40 HP Travaini liquid ring, single stage vacuum pump "TRSC 100-700/C/F". Nominal capacity 500 ACFM @ 20" HgV; max Vacuum 27" HgV. -- Pump materials:Include cast iron housing, ductile iron impeller, and stainless steel shaft. Shaft seals are carbon face with viton elastomers. -- 40 HP:200 Volt, 3-Phase, 60 Hz, TEFC monoblock assembly for direct drive, no field alignment needed. -- Sealing fluid re-circulating system includesReservoir of carbon steel with fluid level gauge and drain, high-efficiency discharge separator and oversized heat exchanger. -- High temp switchTo protect against over-temp operation. -- Suction line accessories includeInlet check valve, vacuum gauge (0 - 30" HgV), inlet filter assembly, manual unloader valve, and vacuum relief valve. -- Heat exchangerIs an air cooler type made from aluminum and extended surface fins. -- Electrical controls include:Starter/overload reset, pump running light, hour meter, hi-temp light, and terminal blocks, all mounted in a NEMA 12 cabinet.

Tri State Machinery Straight Line Rip Saw S/N 4.5.74-72

Twin City Fan Blower Air Lock Can BE Added For Additional Cost

TWIN FLOW Air Make-Up Unit 14,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 14,000 CFM @ 1.75" ESP, 10 HPTEFC motor -- BTU: 1.38 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire. -- Also available: Controls option: - Two stages for 14,000 or 7,000 CFM at extra cost of about $3,000.

TWIN FLOW Air Make-Up Unit 7,000 CFM. Vertical mount with Remote Control Panel: -- CFM: 7,000 CFM @ 1.75" ESP, 5HP/575v/3ph/60Hz TEFC motor -- BTU: 0.68 MBTUH -- Burner: MAXON burner -- Temperature Control: 80º F temperature rise in spray cycle -- Mounting: Vertical, outdoor/indoor mounted -- Fuel required: Natural gas, 0.3 PSI pressure -- Intake/Discharge: Vertical, screened, air intake with vertical discharge -- Filter Sections: V-Bank style with 1’’ cleanable air intake disposable type filters -- Gas Control: Control cabinet and pre-piped gas combustion system mounted on burner section to FM, Electronic Modulation -- Specifications includes: Digital Temperature Controller, ON/OFF & Summer/Winter Switch, pressure regulator, metering valve, pilot pressure regulator & pilot gas valve, flame rod, high limit switch, air flow switch, power transformer, ignition transformer and spark plug -- Electrical Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Motor Control: Control cabinet includes: main breaker disconnects, magnetic motor starters with adjustable overload protection for air makeup, motor fuse protection -- Enclosure Design: Framed, with 18 ga. metal walls and 1" insulation -- Note: Available in Horizontal and Vertical mount. Please inquire.

ULTRA GL-630H Feed Through Moulder: 6-Head (B-T-R/L-T-B), "Flooring" working capacity of 12" x 6".Specifications: -- Head sequence: Bottom 25 HP, top 30 HP, right 20 HP/left 20 HP (opposing), top 25 HP, and bottom 25 HP motor. -- Spindle dia. of 1-13/16" with cutterhead speed of 6,000 RPM; all spindles with high prevision bearings. -- Auto. positioning of the left & top spindles radially; all additional spindles with digital readouts, including chipbreaker & pressure elements. -- Pneumatics on all chipbreakers, pressure elements, and holddown rollers. -- Horizontal spindles with HydroLock outboard bearings on #1, #2, #5 & #6. -- Straight jointer on spindles #5 & #6; Profile Jointers on spindles #3, #4, #5 & #6. Equipped with: -- Inverter controlled feed drive, variable speed of 26 - 260 FPM. -- Infeed table 1.2 M (4') with all table plates & fences hard chromed to RC 70. -- Machine table includes: (5) Table rollers for smooth through feed; short stick attachment for through feed on pieces down to 230 mm. -- Electrical cabinet & pedestal for machine controls separate from machine, Heavy Duty sound enclosure. -- Includes Startup training and Warranty!

UNIQUE - 313, ...Automatic Cope & Dowel Door MachineMiters the end & drills for dowels of (2) cabinet door rails on each pass; automatic cycle for accurate & easy alignment of mitered corners.Equipped with: -- (2) 5 HP Dual motor set for shaping w/1-1/4" spindles; (2) 0.33 HP dowel alignment drills. -- Automatic cycle with: Dowel hole boring for accurate alignment of mitered door corners in (15) Sec/cycle. -- 1" Material thickness cap., 4" max. material width, 5" max. cutter diameter. Features: -- (2) Pneumatic clamps hold material during operation for safe machining of parts; adjustable stops for dowel drilling; air over oil rodless cylinder driven table. -- Staggered tables with angled fences allow: (2) 1" Thick parts to be machined simultaneously; digital position indicator. -- Dust Collection: (2) 5" Dust ports require approx. 1,000 CFM per spindle.

UNIQUE 2700 CNC CNC Door ShaperCNC Controlled Machining Center for Raised Panel Doors.Equipped with: -- (1) CNC controlled 5" stackable vertical spindle (max. 4 tools per stack), 7.5 HP belt driven; max. clamping thickness 2-1/2" and 6" max. cutter head diameter. -- "X" Axis of spindle travels 81" on (2) THK rails with ball screw movement, "Y" axis with 5" travel on THK rails with 5" max. workpiece overhang, "Z" axis with 5" max. travel on THK rails.Features: -- Windows based PC computer with large touch screen menu for quick set-up, new door or custom door stiles can be programed in minutes, automatic operation from one style and size of door to the next, straight raised panels & widths of stile or rail and end tenoning work the same. -- Electronic sensors measure the length of the part to be cut allowing for various width panels or rails to be shaped consecutively, once a door is pre-programmed it can be re-called.Complete with: Electronic brake on spindles, (2) 5" dia. outlets for dust collection and UNIQUE's Windows based "Raised Panel Door" Software. .