Woodworking Equipment For Sale

BRANDT - "KD-68", ...Edgebander1/4" (6 mm) Edge thickness cap. (will even do 8 mm max.); max. edgebanding height: 60 mm (2-3/8"); min. workpiece length: 160 mm; width: 70 mm (2-3/4").Equipped with: -- Quick Melt Glue System with: (10) Min heat up time and reversible glue roller. -- Automatic magazine for strip & coil stock; 3 mm PVC guillotine; 3-roller Pressure Section.Workstations: -- Double motor end trim on uni-slide: 0.33 HP - 14,400 RPM; chamfers 0° - 15°. -- Top & Bottom flush/bevel & radius trim; bevels 0° - 15°; 1/2 HP - 14,400 RPM motor ea.; w/SIKO digital readouts. -- Top & Bottom scraping for standard or 3 mm PVC edging; air jet blowoff; SIKO digital readouts. -- Top & Bottom buffing: 1/2 HP - 1,650 RPM; adjusts 0° - 40°. -- Feed chain feed speed: 36 FPM.Complete with: Electronic motor brakes on both trimmers; padded sound enclosure; eye level height swivel control panel w/fault sensor control; adjustable outboard panel support track; frequency converter; used tooling.

BRANDT KDF 780 2C EDGEBANDER WITH PRE-MILL AND CORNER ROUNDINGBasic Specifications: -- 0.4 - 15 mm (5/8") Edge cap., panel thickness 5/16" - 2-3/8", min. panel length 160 mm (6-3/8") and 65 mm (2-3/8") min. width; line control (NO limit switches) for workstation function.Features: -- Pressure Beam with motorized height adjustment for all work stations includes digital height indicator. -- PC-20 Program Control; with 12" Industrial PC flat screen 256 MB RAM, 1 GB Flash Card, with USB Port & remote diagnostic link. -- Signal infeed light to ensure proper spacing between panels. -- Quick heat-up glue system,(approx. 10 minutes) w/hopper feeder & w/glue tank for maintenance & quick glue color change. Glue temperature indicator for both the glue pot and glue roller with LED thermostat and automatic temperature reduction if the machine is idle for 15 minutes or more. -- The glue applicator roller is also reversable and retractable from the fence line. -- Automatic magazine for strip & coil (large coil table 800 mm diameter to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine, (1) drive plus (3) secondary rollers "pneumatically controlled" pressure section. -- Variable Feed speed 36 - 65 FPM (3 HP feed motor) -- Corner rounding station operates at 16 m/Min (52 FPM).Workstations: -- (2) Motor Pre-milling Unit; (2) 3 HP motors (12,000 RPM) to clean-up potential chipped edges. -- End Trimming: (2) 1/2 HP - 12,000 RPM motors) chamfers 0° - 15° via programmable controller. -- Pre-Trimming: Top & bottom flush/bevel trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Fine-Trimming: Top & bottom flush/bevel/radius trim, bevels 0° - 15° (3/4 HP - 12,000 RPM motor), with (4) postion manual index turret and pneumatic air cylinder for pre-set tool positioning. -- Corner Rounding (Contour) Trimming Unit: (2) motor 1/2 HP - 12,000 RPM each motor for corner rounding for front & trailing corners on the fly. -- Profile Scraping Unit: Top & bottom for 1 - 3 mm PVC radius, depending on tooling. -- Open Space: For the ability to add a top & bottom flat/glue scraper. -- Buffing Station: Top & bottom oscillating buffing (0.25 HP - 2,800 motors). -- Hot Air Unit: (1) Hot air blower to reactivate top/bottom edge after profile scraping and buffing, restoring original edge color luster.Complete With: -- Operator control panel w/PLC (Programmable Logic Control) keypad & LED readouts. -- End trim, flush trim & fine trim and corner rounding stations have HF motors with electronic brakes. -- Original Factory machine documentation.

Brewer BR-425 Step Planer

Brewer Step Planer 24in, BR425, S/N 12286, 50HP Electric Motor Up to 6" thick

Brewer 1695 Chop Saw 20HP 3 strand log deck Live roll 15' infeed 10' outfeed Needs chains and rollers

Brewer 3 Head Resaw Model: Golden Eagle 2000 Year: 1998 Blade Size: 2" Voltage: 480 3ph Material Capacity: 7.5" - 12" width Serial #: No Placard Condition: Fully Functional, no rust, Updated electrical panel. Spare Parts: 2" Blades Dimensions: 20' long x 11' wide New Bearing on all wheels front and back. We put a new rubber belt on the infeed, we still have the steel belt infeed if they want to change it back. About 20-40 2” band saw blades included. Saw Head 3 has 1 new motor.

BRIDGEWOOD BW-511MS Sliding Table Shaper Single Phase 4 HP Motor with forward & reverse.Specifications: -- 3/4″ Spindle with 4-1/2″ under the nut, and 3-1/2" of Spindle travel. -- (5) Spindle speeds: 3000, 4000, 6000, 8000 and 10000 RPM. -- 52" Table Length, and 35 Sliding Table Length1-used BRIDGEWOOD BW-511MS SLIDING TABLE SHAPER. Table Length: 35″, Sliding Table Length: 52″, 3/4″ spindle with 4-1/2″ under the nut, Also , Spindle Travel: 3-1/2″, Motor: 4 HP, single phase, (5) spindle speeds: 3000, 4000, 6000, 8000 and 10000 RPM. For operation on 220V, 1PHNote- the feeder in the photo is not included

16” Width Capacity Approx 15 HP Top Head Approx 10 HP Bottom Head Feed 23-65 FPM 220 Volt 3 Phase

BRIDGEWOOD - BW-508 PV ...Planer20" Width cap.; 1/4" - 9" opening; 7-1/2 HP motor (3-phase) with: 1-1/2 HP Feed motor; both made in the USA; variable feed speed: 20 - 32 FPM.Complete with: Segmented infeed roller; cast iron chip breaker and adjustable bed feed rollers; 3-knife cutter with jack screw adjustment. - Includes (2) sets of knives.

New conveyor system that is NEW/NEVER INSTALLED. Everything is ready to load and will take approx two full flatbed trucks to move. See photos for all specs.

•Burelbach 4 x 10ft stacker •Removed from plywood mill that went out of business, was in use at time of shut down •Currently stored inside

This machine was customized to be a wire brush machine for a floor finishing line.

Manufacturer Specifications Width capacity 1300 mm Panel thickness: 3 - 80 mm variable feedspeed 6-30 m/min Coating roller 55° Shore with variable speed and scraper Chrome doctor roller with variable speed and scraper

Burkle Roll Coat Line (2) Roll Coaters Filler UV Oven Brush Machine IR Oven This system was removed in good working condition with low hours.

SLC 1300 Roll Coater 1300 mm wide

BURKLE - VBM 1688, ...Stain Wiping MachineSingle sided machine, 1,600 mm wide; 2-Brush Panel Cleaner (TAMPICO brushes). Features: &#9679 Heads can be positioned as needed spacing between the brushes by sliding brackets. &#9679 Brush raising & lowering accomplished by means of handwheel adjustment. &#9679 Brushes are removed at side of machine by sliding out of shroud/channel support rail. &#9679 Safety bar checks part thickness for overthickness parts. &#9679 SIEMENS Control to set rotation speeds & feed belt speed. &#9679 Rigid Aluminum bolted base construction. &#9679 Solid feed belt (NO vacuum holddown)

BUSCH MINK MM 1322 A VV8 VACUUM PUMP, ROTARY (DRY CLAW): -- Specifications:360 m³/Hr., Dry Rotary Claw Vacuum Pump, Model: MM 1322 A VV8. Nominal pumping speed displacement 212 ACFM; Ultimate pressure 112.5 TORR; Nominal motor rating 10.9 HP; Nominal motor speed 3,600 RPM;Noise level (ISO 2151) 82 dB(A); Weight approx. 655 Lbs.; Dimensions (L x W x H) 46.9 x 21.5 x 17.9 inches; Gas inlet/outlet, 2" / 1¼" NPT. -- Industry Uses:Woodworking Handling devices, Drying, Handling robots, Clamping on CNC routers, Pneumatic conveying.

BUSCH MINK MM 1322 A VV8 VACUUM PUMP, ROTARY (DRY CLAW): -- Specifications:360 m³/Hr., Dry Rotary Claw Vacuum Pump, Model: MM 1322 A VV8. Nominal pumping speed displacement 212 ACFM; Ultimate pressure 112.5 TORR; Nominal motor rating 10.9 HP; Nominal motor speed 3,600 RPM;Noise level (ISO 2151) 82 dB(A); Weight approx. 655 Lbs.; Dimensions (L x W x H) 46.9 x 21.5 x 17.9 inches; Gas inlet/outlet, 2" / 1¼" NPT. -- Industry Uses:Woodworking Handling devices, Drying, Handling robots, Clamping on CNC routers, Pneumatic conveying.

BUSELLATO B1CNC CNC MACHINING CENTER (UNIVERSAL): -- Specifications: Design Type: Cantilever Style, 49" x 120" universal phenolic machine table, multizone "Universal" vacuum table for use with pods. -- Equipped with:(1) 10 HP ISO 30 Type ATC spindle; variable speed from 3,000 - 18,000 RPM; (7) position side tool magazine; (1) Multispindle boring block (7-vertical, 4-horizontal) with an X-axis grooving Saw. -- PC-Based ControlWith "Windows 2000 Professional", GENESIS EVOLUTION programming software, Rail plan for pod location software, Autolink DXF conversion software, Autobar labeling software, Gencode barcode reading software. -- Complete with:(1) 80 Cubic meter rotary vane Vacuum Pump; assorted tooling; documentation; manuals and applicable software media.NOTE: This machine has very low usage and was used more like a Hobby/R+D CNC Machining Center by the owner.INCLUDES: -- CORAL - CA/3C Dust Collector; (3) canvas filter Bags; (3) HD plastic Collection Bags; 10" dia. intake flange; 3,105 CFM; 5.5 HP motor, 3/220/440 Volt; complete with on/off starter.

BUSELLATO JET 4002 XL CNC MACHINING CENTER (W/ATC/BORING): -- Specifications: Working Field "X" Axis of 168.1" (4,270 mm); "Y" axis of 47.2" (1,200 mm); "Z" axis stroke 9.8" (250 mm); 6.8" (175 mm) max. material thickness. -- Positioning Speed:"X" Axis at 230 FPM (70 MPM); "Y" axis at 197 FPM (60 MPM); "Z" axis 49 FPM (15 MPM). -- Worktable:(8) Pneumatic locking panel supports, (3) vacuum pods per support.(8) Pneumatic backstops, (2) pneumatic side stops & (2) pneumatic central stops.(4) Independent working zones; jig locking device on (2) work areas. -- Boring Head:(1) 4 HP (3 kW) Motor - 4,000 RPM; (20) vertical spindles with: (12) Spindles in "X" axis & (8) spindles in "Y" axis. -- Machining:(1) Vertically mounted 10 HP (7.5 kW) electro spindle with: ISO-30 Adaptor (0 - 18,000 RPM) with RH or LH rotation; (1) 6-position automatic tool changer.(1) Additional 5 HP (3.8 kW) vertical router; routers are driven by an 11 kW Digital Inverter -- Operator & Machine Control:PC Front-End with: "GENESIS EVOLUTION" 2.2.1 + Windows "NT" Operating System; 15" color monitor; 1.44 MB floppy & 32X CD ROM drives; 8.4 GB hard disk; 64 MB RAM; (2) RS 232 serial ports; integrated modem; Ethernet card, all built into a protective cabinet enclosure.GENESIS Software is continuously online providing real-time information on tool position & error messages, visualization of RPM, current load meter, and more; positioning of panel supports and vacuum cups.Software features: Automatic generation of G & M code, stop & restart, machine diagnostics, automatic optimization, and full graphic display with the possibility to associate up to (11) parameters and programming of up to (2,000) work lines per single program. -- Complete with:Front safety mats that will instantly place machine in "Pause Cycle" when operator steps onto the mats. Safety Perimeter Fencing. Transformer for 480 V. -- Actual Model is: Busellato Jet 4002 XL.